Table of Contents
Advertisement
Available languages
Available languages
Quick Links
ASSEMBLY AND INSTALLATION
T0696 / T0697
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#8/32X1/2 in
#6/32 X1/2 in
Tools Needed:
(1) Phillips-head Screwdriver
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 2-150 W (bulb not included)
Working Temperature Range: -
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Rotate the sensor head towards the back plate.
Backplate
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Strap
#10/24 X1/4 in
(2) 1/8" Flat-head Screwdriver
13°F ~ 113°F
Controls
Page 1 / 5
Decorative cover
Fixture Mounting Screw
1. Phillips-head screwdriver for attaching mounting screws to
mounting strap, mounting bracket and fixture to mounting bracket.
2. 1/8" wide flat-head screwdriver for connecting the source wires
into the wiring terminal station on the mounting bracket.
Features:
1. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF or remains
in low-level brightness when motion stops.
2. Photocell keeps the light OFF during daylight hours.
Eave Mounted
Rotate the sensor head clockwise 180˚ so the controls face down.
Controls
Wire Connector
Gasket
Controls
221031
Advertisement
Table of Contents
Related Manuals for Vaxcel T0696
Summary of Contents for Vaxcel T0696
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0696 / T0697 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
-
Page 2: Installation Steps
Decorative Cover Decorative Shell FRONT Outlet Box PAR 38 Bulb Max.150W (not included) Mounting Strap Wire Connector Backplate Installation Steps Turn off the power at fuse or circuit box. 1. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two mounting screws that best fit the outlet box. -
Page 3: Adjusting The Light Head
Fig. 2 Fig. 3 Sensor Adjustment Lower For Short Coverage Sensitivity of Motion Sensor ● You can adjust the sensitivity of the motion sensor by using the “SENS” knob located on the right side of the bottom surface of the sensor. (See Fig. 4) ●... -
Page 4: Customization Options
Functions and Operations (continued) 5. 3 HOURS (3H) MODE (nighttime operation only) ● In “3H” mode, the light turns to high-level brightnes at dusk, and stays on for 3 hours, then it turns to low-level 30% brightness. It turns to high-level brightness when motion is detected, and stays on as long as motion continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you set (30s/1min/3min), then returns to the low-level 30% brightness automatically. -
Page 5: Troubleshooting
Gasket #8/32X1/2 in #6/32 X1/2 in #10/24 X1/4 in Assembly Kit 6609MM (1 SET) FOR T0696 6610MM (1 SET) FOR T0697 Troubleshooting ---The light does not work. 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring is correct. -
Page 6: Herramientas Necesarias
INSTRUCCIONES DE ENSAMBLAJE E INSTALACIÓN T0696 / T0697 ADVERTENCIA: PARA EVITAR EL RIESGO DE CHOQUE ELÉCTRICO, ASEGÚRESE DE APAGAR LA ENERGÍA ANTES DE INSTALAR O HACER EL MANTENIMIENTO DE ESTE ARTEFACTO. NOTAS: 1. Antes de instalar, consulte los códigos de electricidad locales para ver los requisitos de cableado y conexión a tierra. - Page 7 Cubierta decorativa Carcasa decorativa FRONT Caja de toma de corriente Bombilla PAR 38 150 W máx. (no se incluye) Placa de montaje Conector de cable Placa posterior Pasos de la instalación Apague la corriente en la caja de fusibles o de circuitos. 1.
-
Page 8: Funciones Y Operaciones
Fig. 2 Fig. 3 Ajuste más bajo del sensor para cobertura corta Sensibilidad del sensor de movimiento ● Puede ajustar la sensibilidad del sensor de movimiento usando el selector de "SENSIBILIDAD" ubicado a la derecha en la superficie inferior del sensor. (Vea la Fig. 4) ●... -
Page 9: Opciones De Personalización
Funciones y operaciones (continuación) 5. MODO de 3 HORAS (3H) (solo funcionamiento nocturno) ● En el modo de "3H", la luz pasa al brillo de nivel alto al anochecer y permanece encendida durante 3 horas, luego pasa al brillo de nivel bajo. Se enciende al brillo de nivel alto cuando se detecta movimiento y permanece encendida mientras continúe el movimiento. -
Page 10: Resolución De Problemas
6/32 X1/2 in 10/24 X1/4 in del artefacto Kit de ensamblaje 6609MM (1 JUEGO) PARA T0696 6610MM (1 JUEGO) PARA T0697 Resolución de problemas ---La luz no funciona: 1. Asegúrese de que el interruptor de pared y la llave disyuntora estén encendidos.