Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0437
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to
the sensor, be sure the power is switched "off" before
replacing the bulb.
8. Compatible with LED dimmable bulb.
Maximum Wattage: 60W Incandescent Bulb or 20W LED
dimmable bulb.
Work Temperature: -4°F~104°F
Headless Screw (D)
Mounting Plate (A)
Lock Nut (E)
House Grounding Wire
Outlet Box
Green Grounding Screw (C)
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Wire Connector (F)
Fixture Grounding Wire
Type A Max. 60W Bulb or
Max. 20W Dimmable LED Bulb
(not include)
Page 1/4
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or garage
door. Use the dark-to-bright illumination option
where you do not need minimum brightness, such
as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included)
Mounting Plate (A)
Back Plate
Fixture Wire
Mounting Screw (B)
Green Grounding
Screw (C)
Wire Connector (F)
Ball Nut (G)
Fixture
Rubber Pad (H)
Ball Nut (G)
Socket
Glass Panel
180928
Headless
Screw (D)
Rubber Pad (H)
Advertisement
Related Manuals for Vaxcel Mission T0437
Summary of Contents for Vaxcel Mission T0437
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0437 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Important to Know Features 1.
- Page 2 Turn on the power at fuse or circuit box 1. Thread two headless screws (D) through the mounting plate (A), then secure them with four lock nuts (E) (two on each side of the mounting plate). Adjust the length of the headless screws (D) if necessary. Notch Note: Make sure that the headless screws are lined up horizontally, to ensure that the fixture will be level.
- Page 3 5. Manual Override MODE (nighttime operation only; on at dusk,off at dawn) ● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again, the light will turn to high-level brightness at dusk, and turn off automatically at dawn. To return to the previous settings, turn off the wall switch in 3 seconds and then turn it on again.
- Page 4 ---In 3H or 6H Mode, the light is still on full brightness, even though it has been 3 hours or 6 hours after dusk, respectively: 1. Make sure no motion could be picked up by the sensor. 2. Make sure that mode entry is not in manual override. ---After performing 3H or 6H Mode, the light stays on full brightness after 3 minutes: 1.