Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Paradyne Manuals
  4. Extender
  5. SNE2040G-P
  6. Installation instructions

Paradyne SNE2040G-P Installation Instructions

Replacement prom
Hide thumbs Also See for SNE2040G-P:
1
2
3
4

Advertisement

Quick Links

Download this manual See also: Instruction and Installation Manual
SNE204G Replacement PROM
Installation Instructions
Document Number SNE2-A2-GK40-00
September 2004
Purpose of the Replacement PROM
The replacement Programmable Read-Only Memory (PROM) integrated circuit for
the SNE2040G network extender provides the following enhancements:
„
„
Replacement Procedure
To install the replacement PROM:
Procedure
SNE2-A2-GK40-00
SNMP Management – The new firmware on the PROM provides support for
Paradyne enterprise MIBs and selected MIB II OIDs.
Flash Download Capability – Future upgrades will not require replacement of
the PROM. You will be able to download new firmware using TFTP.
HANDLING PRECAUTIONS FOR
!
STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
1. Remove the power cord from the SNE2040G.
2. Using a Phillips screwdriver, remove the four screws at the top, bottom, and
sides of the SNE2040G.
3. Using a 3/8-inch socket or a pair of pliers, remove the nut and washer holding
in the place the power receptacle at the back of the SNE2040G.
4. Carefully pull apart the top and bottom covers of the SNE2040G and lay them
side by side. The two parts will remain connected by wires between the fan
and the circuit card.
5. Locate the PROM on the circuit card. Note the orientation of the writing on the
PROM so that you can orient the new PROM the same way.
September 2004
1

Advertisement

loading

Related Manuals for Paradyne SNE2040G-P

Summary of Contents for Paradyne SNE2040G-P

  • Page 1 SNE204G Replacement PROM Installation Instructions Document Number SNE2-A2-GK40-00 September 2004 Purpose of the Replacement PROM The replacement Programmable Read-Only Memory (PROM) integrated circuit for the SNE2040G network extender provides the following enhancements: „ SNMP Management – The new firmware on the PROM provides support for Paradyne enterprise MIBs and selected MIB II OIDs.
  • Page 2 6. Using a PROM removal tool (such as AMP Part Number 822154-1), pry up one corner of the PROM slightly at one of the two extraction slots. Then pry it up slightly from the opposite extraction slot. Repeat until the PROM is free of the socket.

  • Page 3: Software And Firmware License Agreement

    Software and Firmware License Agreement ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT. IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE...
  • Page 4 Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from one state or jurisdiction to another.

This manual is also suitable for:

Sne2040g-sSne204g