Table of Contents
Advertisement
®
Hotwire
ReachDSL
Model 6310-A4, with Inline Phone Filter
Installation Instructions
Document Number 6310-A2-GN12-00
September 2001
Contents
......................................................................................................
Hotwire 6310 ReachDSL v1 (MVL) Modem Overview
®
The Hotwire
6310 ReachDSL
the Hotwire ReachDSL System and interoperates with the Hotwire 8310 MVL, or
Hotwire 8312/8314 ReachDSL Card in the DSLAM (Digital Subscriber Line Access
Multiplexer) system. This system provides high-speed Internet or corporate LAN access
over traditional twisted-pair copper telephone wiring.
The ReachDSL technology:
T
Utilizes an inline phone filter on the ReachDSL modem's PHONE jack.
T
Operates over existing copper wire with existing telephone jacks.
T
Includes a second line pass-through from the ReachDSL modem's LINE jack to
PHONE jack to accommodate an attached 2-line telephone.
T
Provides rate adaptive data rates to dynamically adapt and allocate bandwidth to
optimize applications.
™
..............................................................................................
.............................................................................................
.................................................................................... 11
........................................................................ 16
™
version 1 (formerly MVL
®
v1 (MVL
) Modem,
................................................ 10
.............................................. 10
............................................... 13
1
..................................
.......................................
................ 15
...................................... 21
®
) Modem is a component in
1
4
5
8
9
Advertisement
Table of Contents
Related Manuals for Paradyne 6310
Summary of Contents for Paradyne 6310
-
Page 1: Table Of Contents
HomeLink (for ReachDSL v1 Modems Only) Increasing the Number of End-User Systems Cables & Connectors Optional ReachDSL Modem Wall Placement Technical Specifications for Hotwire 6310 ReachDSL v1 Modem Important Safety Instructions Warranty, Sales, Service, and Training Information Hotwire 6310 ReachDSL v1 (MVL) Modem Overview ®... -
Page 2: Hotwire Reachdsl System
In addition, the ReachDSL v1 technology: Transforms a single copper pair into multiple virtual lines to support multiple services simultaneously. Supports simultaneous multiple access of four ReachDSL v1 modems with up to 254 end-user systems sharing one common WAN interface. Features HomeLink, which provides peer-to-peer communications, including print and file sharing applications (see page 10). - Page 3 Depending on the type of phone handset and the quality of the home or business wiring, a phone filter is recommended to minimize background noise during a phone conversation. An internal phone filter is included with the Hotwire 6310 ReachDSL v1 Modem. If additional telephones are used on the same phone line as the ReachDSL modem, install one phone filter on each telephone.
-
Page 4: Getting Started
Standard RJ11 (or RJ14) wall jack for the ReachDSL modem cabling. Standard Ethernet 8-pin, non-keyed modular plug for a PC or workstation. An Ethernet straight-through or crossover cable is used. — Refer to Installing the Hotwire 6310 ReachDSL v1 Modem Ethernet installation details. Cables & Connectors — Refer to cable pin assignments. -
Page 5: Installing The Hotwire 6310 Reachdsl V1 Modem
Installing the Hotwire 6310 ReachDSL v1 Modem Place the ReachDSL modem on a flat surface with clearance for the rear connectors. Procedure 1. If a telephone is connected at the RJ11 wall jack where the modem will be installed, unplug the telephone line from the wall jack. - Page 6 4. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET. — Use a straight-through cable and connect the other end to an Ethernet hub. (To connect to a hub’s Uplink connection, use an Ethernet crossover cable). Ethernet –or–...
- Page 7 5. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the transformer into an AC outlet. Power Jack Transformer 01-17010 The ReachDSL modem hardware installation is now complete. When the power cord is installed, the ReachDSL modem goes through a power-on self-test.
-
Page 8: Power-On
Power-On When power is applied, the ReachDSL modem performs self-diagnostics and the PWR LED is on. The self-diagnostics includes a power-on self-test and all of the LEDs turn on for one second. ReachDSL Status LEDs All of the LEDs turn on and off during the power-on self-test. After a successful self-test, the LEDs should appear as indicated in BOLD in the Condition column below. -
Page 9: Troubleshooting
PWR LED is functioning. TST LED is on. A test initiated by the service provider may be active. Wait five minutes. If the TST LED does not go off, contact the service provider. Installing the Hotwire 6310 ReachDSL v1 on page 5. -
Page 10: Homelink (For Reachdsl V1 Modems Only)
To improve data transmission throughput and minimize background noise during a telephone conversation, make sure that: The Hotwire 6310 ReachDSL v1 Modem is always powered on, even when not in use, and A Hotwire phone filter is installed on every telephone on the same line as the... -
Page 11: Cables & Connectors
Cables & Connectors This section is reference information. Standard twisted-pair CAT3 or better cables are recommended. The LINE and PHONE interface connectors use 6-pin, non-keyed modular plugs. RJ11 or RJ14 6-pin connectors can be used. Line & Phone Connectors Pin # Function Not used Ring 2 (optional) DSL Ring 1... - Page 12 The Ethernet interface connector uses an 8-pin, non-keyed modular plug. — To connect the ReachDSL modem to an Ethernet hub, use the straight-through connection. 8-Pin Straight-through Connection Pin # Function 10BaseT TX D+ 10BaseT TX D– 10BaseT RX D+ 4 & 5 Not used 10BaseT RX D–...
-
Page 13: Optional Reachdsl Modem Wall Placement
Optional ReachDSL Modem Wall Placement The Hotwire 6310 ReachDSL v1 Modem is designed for tabletop placement. The ReachDSL modem can also be mounted on a wall. To mount the modem, you will need: Two slotted-head #6 self-threading screws with plastic anchors Drill and 3/16"... - Page 14 ReachDSL Modem Hardware Template 01-17014...
-
Page 15: Technical Specifications For Hotwire 6310 Reachdsl V1 Modem
Technical Specifications for Hotwire 6310 ReachDSL v1 Modem Item Height x Width x Depth Weight Power Class 2 Transformer normal service input voltage range Approvals FCC Part 15 CISPR 22 Other Certifications Physical Environment Operating temperature Storage temperature Relative humidity... -
Page 16: Important Safety Instructions
Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. - Page 17 CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: Directive 73/23/EEC – Council Directive of 19 February 1973 on the harmonization of the laws of the member states relating to electrical equipment designed for use within states relating to electrical equipment designed for use within certain voltage limits, as amended by Directive 93/68/EEC.
-
Page 18: Declaration Of Conformity
Trade Name: Hotwire Model Number: 6310-A4-200 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 19: Government Requirements
Equivalence Number (REN) for this equipment. The label is located on the bottom of your modem. 2. The Hotwire 6310 ReachDSL v1 Modem connects to the Public Switched Telephone Network (PSTN) using the Universal Service Order Code (USOC) RJ11C or RJ14C. - Page 20 8. This equipment cannot be used on public coin service provided by the telephone company. Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information.) 9. An FCC compliant telephone cord with modular plugs may be provided with this equipment.
-
Page 21: Warranty, Sales, Service, And Training Information
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. - Page 24 " *6310-A2-GN12-00*...