NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
• Keep these instructions. • Heed all warnings. • Follow all instructions. Installation Guide & Warranty Model Numbers | H27H38DT • H32H38DT Direct-View Concierge TVs 1. Do not use this apparatus near water. 2. Clean only with a dry cloth.
IMPORTANT SAFETY INSTRUCTIONS 8. Use only with the cart, stand, tri- pod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTABLE CART WARNING 9.
A brief overview of the features on this TV Analog and Digital Tuners This TV is equipped with both analog and digital tuners. The analog tuner is used for standard over-the-air antenna and cable type (CATV) sources. The digital tuner is provided to receive over-the-air digital programming.
Setup Checklist Following are the steps necessary to install and set up the TV Setup and Operation Checklist 1. Unpack the TV and all accessories. 2. Connect the TV to antenna and all external video source equipment. See pages 10 - 18.
ALARM Press to display menu, fol- low on-screen instructions to set a time for the TV to turn itself on. CHANNEL PREVIEW (Not functional for digital channels - some models.) Displays available analog...
For entering digital chan- nel numbers e.g. 7-1, 11- 3 etc. (SLEEP) TIMER Press repeatedly to choose a TV turn-off time up to 4- hours. Use to set AM/PM on the Alarm and On/Off Timer menus. AUDIO Selects available audio languages for digital channels only.
• Digital cable is not available on this TV. • If only one wire provides the signal source, use a high-quality 2-way RF signal splitter and connect it to both the Antenna-Cable and Digital Antenna RF jacks on the TV, see below. Matrix Out Connect external speaker here.
Off Air Antenna Only (provide digital signal to TV if required by using a signal splitter) If you are using an antenna and no other equipment, go to ......page 12 Cable Service Only If you have cable service and no other equipment, go to .
Hook Up an Off Air Antenna Connect an over the air signal source to the TV Over the Air Antenna Locate the Antenna/Cable and Digital/Antenna jacks on the back of the TV. Connect the RF antenna wires that run from the wall...
Hook Up an Off Air Antenna with VCR Connect an over the air signal source to the VCR and TV Over the Air Antenna with VCR Locate the Antenna/Cable In jack on the back of the VCR. Connect the antenna that runs from the wall jack directly to this jack, according to the connection diagram shown to the right.
Hook Up a Cable Box with VCR Connect a cable box and VCR to the TV Cable Service with VCR Locate the In jacks on the cable box and the VCR. Connect a 75 ohm cable between the cable box wall jack and Cable In on the cable box.
Locate the S-Video out jack on the DVD player or VCR. On the DVD player or VCR, connect the S-Video out jack to the S-Video in jack on the TV according to the connection diagram shown to the right. Make the right/left audio connections as indicated.
Hook Up Composite Audio/Video Connect the TV to a composite audio/video source Composite Audio/Video Locate the composite audio/video input jacks on the TV. Connect the composite audio/video input jacks to a composite audio/video device as shown in the illustration. Typ ica l...
Hook Up an External Speaker Connect the TV to an external speaker or amplifier External Speaker Locate the Matrix Out jack on the back of the TV. Connect the Matrix Out jack to an external speaker or audio amplifier as indicated in the illustration.
On the Auto Program Menu, select: OFF AIR ANTENNA/DIGITAL AIR If only over-the-air channels are available, select Off-Air Antenna/Digital Air. CABLE/DIGITAL AIR If you subscribe to a cable service, select Cable TV/Digital Air. SETUP MENU TO PROGRAM AUTO PROGRAM ADD/DEL/BLNK CH.
Installer Note: The Menu, Select, and Adjust Left/Right keys shown above do not have legends on the actual TV. These keys are turned Off in the Installer menu. To enable the Menu, Select and Adjust keys on the front panel, set installer menu item 11-I to 0.
Auto Source Sensing Connections override all other sources. The front Video in jack is an Auto Sense source connection. If you have a device connected to this jack you will not be able to change channels using the TV tuner until you have disconnected the device.
• If a source is not connected, the not available message is displayed. Mini Glossary SOURCE Input or device providing picture and sound to the TV. AUTO SENSE SOURCE Input(s) that the TV automatically switches to when connected. Page 22...
Sets the time the TV will turn off. Ghost Channel Shows the current channel number in red scrolling down the screen. Refer to Installer menu to turn Off. Alarm Sets a time for the TV to automatically turn itself On. Page 23...
Sleep Timer Menu Press CC. Turns selected option Press TIMER. Shows remaining on or off for both analog and time before TV turns itself off. digital captions. See Caption / Select a preset turn-off time Text pages to set up options.
Add/Delete/Blank Channel Setup Fine-tune the channel selection list Use the MENU key on the optional Installer’s remote to access the Setup menu. Use SELECT to highlight the Add/Del/Blnk option. Using either the NUMBER keypad and ENTER or the Channel Up/Down arrow on the remote, select a channel.
Setting Preset Channel Labels Selecting channel names from the preset Channel Labels Using either the NUMBER keypad or the Channel Up/Down arrows on the optional Installer’s remote, select a channel. Press MENU repeatedly on the optional Installer’s remote until the Setup menu appears.
Source Custom Name Menu This menu enables the Installer to customize source names Press MENU repeatedly on the optional Installer’s remote until the Setup menu appears. Choose the Source Name option using SELECT. Press the Left/Right ADJ arrow to go to the Source Name menu. Use SELECT to choose a Source.
Press ENTER to remove menus. Standard closed captioning is available using the Caption 1 option. Caption/Text are features which allow the TV to display the closed caption and/or text options if made available by the broadcaster. Availability and functionality of Caption/Text options are determined only by each broadcaster and may not be available on every program.
Mini Glossary CAPTIONS The term for the words that scroll across the bottom of your TV screen; usually the audio portion of the program provided for the hearing impaired. TEXT The term for the words that appear in a large black frame and almost cover the entire screen;...
Degauss the Screen Remove color impurities appearing on the screen Press MENU repeatedly on the optional Installer’s remote until the Setup menu appears. Use SELECT on the remote control, to highlight the Degauss option on the menu. Use the Left/Right ADJ arrow to choose ON or OFF.
Language for the On-Screen Menus Choose English, Spanish, (Español) or French (Francais) for the on-screen menus On the optional Installer’s remote, press MENU repeatedly until the Setup menu appears. Use SELECT on the remote control, to highlight the Language option on the menu.
Audio Menu Set up the audio menu options for the end user On the optional Installer’s remote, press MENU repeatedly to go to the Audio menu. Using SELECT on the remote control, high- light the audio menu option you want to change.
MENU key repeatedly until the Video menu appears. Your options are: • Contrast: Adjusts the level of difference between white and black in the TV picture. The more contrast, the brighter the picture appears. • Brightness: Increases or decreases amount of white in the TV picture.
Note: Reset Parental Control Block Hours to Zero and Cancel Password This provides the institution staff and the installer a means to reset the TV to normal opera- tion; if a user has either forgotten the password or has left Parental Control blocks active.
LOCK ON OFF As shown above with the Parental Control menu on-screen, use SELECT to highlight an option like Age Block for TV programs and movies, then press the Right ADJ arrow. Use SELECT, and the Left/Right ADJ arrows to select and adjust or set the rating for an option.
You cannot disable Parental Control by discon- necting the TV from power. Block hours will automatically reset to original block time set- ting specified if power is disconnected. Page 39...
Note: Reset Parental Control Block Hours to Zero and Cancel Password This provides the institution staff and the installer a means to reset the TV to normal operation; if a user has either forgotten the password or has left Parental Control Block active.
101-I Start Minor Channel. When set to 1, cannot tune from current channel. Set to 1 to enable Ghost Channel display. Volume level at TV turn-on (Set 255 to retain last level). Minimum volume setting. Maximum volume setting.
Installer Menu Installer Menu Items 25-I through 62-I Menu Function Value Default Item Range 25-I. FUNCTION PRE. 0 - 3 26-I. NOT USED 27-I. NOT USED 28-I. CH OVER RIDE 0 / 1 29-I. OLD OCV 0 / 1 30-I. ACK MASK 0 / 1 31-I.
Channel-Time on-screen display. When set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel. When set to 1, XDS display program information will not appear. User programmable number, most significant byte.
TV will remain on, unless there has been activity from either the control panel or remote control. *M.P.I. Multiple Protocol Input: ZENITH protocol for remote control of TV through RJ11 (M.P.I.) jack on TV connections panel.
Change values with ADJ (Adjust) Left/Right keys. It may be best to set the same value on every TV. Note: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (See item 8 -I).
18-I. NOT USED 19-I. NOT USED 20-I. FEATURE LEVEL Default set to ZEN 1 for Zenith IR remote control operation. Set O, P LBL for Zenith Private Label IR remote control operation. WARNING: Do not change the default value unless you have the prop- er remote control to operate the TV.
Installer Menu Detailed Descriptions for Installer Menu Items 37-I through 59-I 37-I. REAR Y-C EN. Rear S-Video Enable) Set to 1 to enable the rear S-Video input. Set to 0 to disable the rear S-Video input. 38-I. YPrPb EN. (Not available) Set to 1 to enable rear Component Video input.
= background color and custom color enabled) a large channel number is displayed instead of the normal Channel-Time display. 75-I. REVERT CH (Revert Channel) When set to 1 and loss of M.P.I. communication occurs, TV automatically tunes to the specified Start Channel.
Used with item 4-I Start Channel. Set the major channel number in 4-1 and the minor digital dash number in item 101-I. At TV turn on, start channel number is automatically tuned in. Set to 0 if item 4-I is set to 255 for last tuned channel.
LT2000, use the indicated keys on the HP602, LP702 or MBR3447 LG/Zenith installer remotes, or the front panel keys on the TV receiver. Notes: Use only one MPI port for cloning. Do not run Auto Program while cloning.
A slow flashing green light indicates there is a problem with the communica- tions between the TV and the programmer. In this case, check for a damaged cable, poor contacts or other connection troubles. If the status indicator is red, the programmer batteries are low and should be replaced.
POWER, OR ENTER Since the Clone Programmer’s time can- not be set directly, the time needs to be copied from a Zenith TV equipped with M.P.I. Input capability. Once the time is copied to the Clone programmer, the current time can then be transferred to another TV.
• TV not reset. When cloning operations are complete, just unplug the LT2000 from the TV. If the TV does not display a picture (blank screen) after a few seconds, just change channels. The LT2000 programmer is designed to be used with TVs containing the 221-01006 and later processors.
Some Quick and Easy Tips for Resolving Problems Installer Menu Settings and TV Problems Installer menu item settings dictate how the TV functions. If a feature is not available or a problem can not be solved, check the installer menu settings to assure feature and functional items are set to appropriate levels, etc.
• Sleep Timer turned TV Off. • Off Timer turned TV Off. • Power failure. • Power outlet controlled by switch. Connect TV power cord to outlet that is (Switch turned off.) TV turns On. • On Timer turned TV On.
Troubleshooting Some Quick and Easy Tips for Resolving Problems Symptoms Possible Cause(s) Source Selection / Source Image Problems Camport (Front • Equipment not connected. Audio/Video) source not selectable. No Camport image. • Equipment not turned on. (Front Video) • Not enabled. S- Video Source not •...
Maintenance Routine TV Cabinet and Screen Cleaning Careful and regular cleaning can extend the the useful service life of the TV. Be sure to turn the power off and pull out the power cord before you begin any cleaning. Screen Cleaning 1.
Discrete IR Command Codes A list of the IR discrete codes available and their functions for this TV Code (Hexa) Function Power On Power Off Camport R S-Video Remote Control IR Codes Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz...
Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio. M.P.I. Multiple Protocol Interface: ZENITH protocol for external control of TV through RJ11 (M.P.I.) input jack on TV connections panel.
Zenith Direct-View TV Warranty Direct-View Color TV Welcome to the LG family! We believe that you will be pleased with your new Zenith TV. Please read this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This war- ranty gives you specific legal rights, and you may also have other rights that vary from state-to- state within the U.S.A.