Table of Contents
Advertisement
Available languages
Available languages
4.12 Child Lock
Use Child Lock function to prevent children from
tampering with the machine. Thus you can avoid any
changes in a running programme.
C
If the Programme Selection knob is turned when
the Child Lock is active, "Con" appears on the display.
The Child Lock does not allow any change in the
programmes and the selected temperature, speed
and auxiliary functions.
Even if another programme is selected with the
Programme Selection knob while the Child Lock is
active, previously selected programme will continue
running.
To activate the Child Lock:
1. and 2. Auxiliary Function buttons are pressed
and held for 3 seconds. The lights on the 1
Auxiliary Function buttons will flash, and "C03", "C02",
"C01" will appear on the display respectively while
you keep the buttons pressed for 3 seconds. Then,
"Con" will appear on the display indicating that the
Child Lock is activated. If you press any button or turn
the Programme Selection knob when the Child Lock
is active, same phrase will appear on the display. The
lights on the 1st and 2nd auxiliary function buttons
that are used to deactivate the Child Lock will blink 3
times.
To deactivate the Child Lock:
Press and hold 1
and 2
st
nd
for 3 seconds while any programme is running. The
lights on the 1
and 2
Auxiliary Function buttons will
st
nd
flash, and "C03", "C02", "C01" will appear on the display
respectively while you keep the buttons pressed for
3 seconds. Then, "COFF" will appear on the display
indicating that the Child Lock is deactivated.
C
In addition to the method above, to deactivate the
Child Lock, switch the Programme Selection knob
to On / Off position when no programme is running,
and select another programme.
Child Lock is not deactivated after power failures or
when the machine is unplugged.
4.13 Progress of programme
Progress of a running programme can be followed from
the Programme Follow-up indicator. At the beginning
of every programme step, the relevant indicator light
will turn on and light of the completed step will turn
off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running. To
do this, the change you are going to make must be in a
step after the running programme step. If the change
is not compatible, relevant lights will flash for 3 times.
C
If the machine does not pass to the spinning step,
Rinse Hold function might be active or the automatic
unbalanced load detection system might be
activated due to the unbalanced distribution of the
laundry in the machine.
17 / EN
and 2
st
auxiliary function buttons
4.14 Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
when the water level is unsuitable.
Loading door light will start flashing when the machine
is switched to Pause mode. Machine checks the level of
the water inside. If the level is suitable, Loading Door
light illuminates steadily within 1-2 minutes and the
loading door can be opened.
If the level is unsuitable, Loading Door light turns off
and the loading door cannot be opened. If you are
obliged to open the Loading Door while the Loading
Door light is off, you have to cancel the current
programme; see "Canceling the programme".
4.15 Changing the selections after
nd
programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine
to pause mode while a programme is running. The light
of the step which the machine is in starts flashing in
the Programme Follow-up indicator to show that the
machine has been switched to the pause mode.
Also, when the loading door is ready to be opened,
Loading Door light will also illuminate continuously in
addition to the programme step light.
Changing the auxiliary function, speed and
temperature
Depending on the step the programme has reached,
you can cancel or activate the auxiliary functions; see,
"Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and "Temperature
selection".
C
If no change is allowed, the relevant light will flash
for 3 times.
Adding or taking out laundry
1. Press Start / Pause button to switch the machine
to pause mode. The programme follow-up light of
the relevant step during which the machine was
switched into the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the Loading Door and add or take out the
laundry.
4. Close the Loading Door.
5. Make changes in auxiliary functions, temperature
and speed settings if necessary.
6. Press Start / Pause button to start the machine.
Washing Machine / User's Manual
Advertisement
Table of Contents
