Related Manuals for HPE S5830V2 Series
Summary of Contents for HPE S5830V2 Series
- Page 1 H3C S5830V2 & S5820V2 Switch Series EVB Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 23xx Document version: 6W102-20150315...
- Page 2 Copyright © 2014-2015, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. Trademarks H3C, , H3CS, H3CIE, H3CNE, Aolynk,...
- Page 3 Preface The H3C S5830V2 & S5820V2 documentation set includes 16 command references. These references describe the commands and command syntax options available for the H3C S5830V2 & S5820V2 Switch Series. The EVB Command Reference describes the EVB configuration commands. This preface includes: •...
- Page 4 Command reference Added and modified commands Added commands: • bandwidth • default • shutdown Modified commands: • S-channel aggregate interface view was added to the following commands: description evb mac-learning forbidden evb reflective-relay evb vsi • VSI aggregate interface view was added to the following commands: description evb vsi active evb vsi filter...
- Page 5 Convention Description Asterisk marked braces enclose a set of required syntax choices separated by vertical { x | y | ... } * bars, from which you select at least one. Asterisk marked square brackets enclose optional syntax choices separated by vertical [ x | y | ...
- Page 6 Category Documents Purposes Provides a complete guide to hardware installation Installation guide and hardware specifications. H3C LSWM1HFANSC & Provides the physical views, specifications, LSWM1HFANSCB Fan installation procedures, and removal procedures for Assemblies Installation hot-swappable fan assemblies. H3C LSVM1FANSC & Provides the physical views, specifications, LSVM1FANSCB Fan installation procedures, and removal procedures for Assemblies Installation...
- Page 7 http://www.h3c.com Documentation feedback You can e-mail your comments about product documentation to info@h3c.com. We appreciate your comments.
-
Page 8: Table Of Contents
Contents EVB commands ····························································································································································· 1 bandwidth ································································································································································· 1 default ········································································································································································ 1 description ································································································································································· 2 display evb cdcp ······················································································································································ 3 display evb evb-tlv ···················································································································································· 4 display evb s-channel ··············································································································································· 6 display evb summary ··············································································································································· 7 ... -
Page 9: Evb Commands
EVB commands EVB requires a license. For information about feature licensing, see Fundamentals Configuration Guide. bandwidth Use bandwidth to configure the expected bandwidth of an S-channel interface or a VSI interface. Use undo bandwidth to restore the default. Syntax bandwidth bandwidth-value undo bandwidth Default The expected bandwidth of an S-channel interface or a VSI interface is the default maximum bandwidth... -
Page 10: Description
Predefined user roles network-admin Usage guidelines CAUTION: The default command might interrupt ongoing network services. Make sure you are fully aware of the impacts of this command when you execute it on a live network. This command might fail to restore the default settings for some commands for reasons such as command dependencies and system restrictions. -
Page 11: Display Evb Cdcp
Views S-channel interface view, S-channel aggregate interface view, VSI interface view, VSI aggregate interface view Predefined user roles network-admin Parameters text: Specifies a description for the interface, a case-sensitive string of 1 to 255 characters. Examples # Configure the description for the S-channel interface S-Channel 1/0/1:10 as S-Channel to lab. <Sysname>... -
Page 12: Display Evb Evb-Tlv
Examples # Display CDCP negotiation information for all interfaces with EVB enabled. <Sysname> display evb cdcp ---------------------------Bridge-Aggregation1--------------------- S-component capability : Local-supported/Remote-not supported Supported S-Channel numbers per-port : Local-167/Remote-0 SVID range : 2-4094 SCID requested from remote SCID/SVID pair list allocated <1, 1>... - Page 13 Parameters interface: Specifies an interface. If you do not specify an interface, the command displays EVB TLV negotiation information for all interfaces with EVB enabled. interface-type { interface-number | interface-number:channel-id }: Specifies a Layer 2 Ethernet interface, Layer 2 aggregate interface, S-channel interface, or an S-channel aggregate interface by its type and number.
-
Page 14: Display Evb S-Channel
Field Description Support for the RR mode on the EVB bridge: • Local RR capability Supported. • Not supported. Local RR status RR status on the EVB bridge after EVB TLV negotiation. Support for Group ID on the EVB station: •... -
Page 15: Display Evb Summary
Parameters interface interface-type interface-number: Specifies an interface (Layer 2 Ethernet interface or Layer 2 aggregate interface) by its type and number. If you do not specify an interface, the command displays S-channel information for all interfaces with EVB enabled. Examples # Display S-channel information for Ten-GigabitEthernet 1/0/1. -
Page 16: Display Evb Vsi
Field Description Port number Port number of the default VSI manager. Interface Name of the interface with EVB enabled. S-channel number Number of S-channels. VSI number Number of VSI interfaces. display evb vsi Use display evb vsi to display VSI interface information. Syntax display evb vsi [ verbose ] [ interface interface-type { interface-number | interface-number:channel-id | interface-number:channel-id.vsi-local-id } ]... - Page 17 <Sysname> display evb vsi verbose interface ten-gigabitethernet 1/0/1 S-Channel1/0/1:100 S-Channel1/0/1:100.0, VSI local-ID: 0, VSI type ID: NA, VSI type version: NA, VSI instance ID: NA, VSI manager ID: NA, Current VDP status: Pre-association, Filter type: VID, Filter info: <100> S-Channel1/0/1:100.1, VSI local-ID: 1, VSI type ID: 100, VSI type version: 0,...
-
Page 18: Display Interface
display interface Use display interface to display information about an S-channel interface, an S-channel aggregate interface, a VSI interface, or a VSI aggregate interface. Syntax display interface [ s-channel | schannel-aggregation ] [ brief [ down ] ] display interface [ { s-channel | schannel-aggregation } [ interface-number:channel-id | interface-number:channel-id.vsi-local-id ] ] [ brief [ description ] ] Views Any view... - Page 19 Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation PVID: 1 Port link-type: trunk VLAN Passing: 1(default vlan), 2 VLAN permitted: 1(default vlan), 2 Trunk port encapsulation: IEEE 802.1q Last clearing of counters: Never Input (total): 6 packets, 384 bytes Output (total): 18 packets, 1152 bytes...
-
Page 20: Evb Default-Manager
Table 6 Command output Field Description Interface status: • Administratively DOWN—The interface is administratively down. Current state • DOWN—The interface is administratively up but physically down. • UP—The interface is both administratively and physically up. Hardware Address Hardware address of the interface. Description Description information for the interface. -
Page 21: Evb Enable
Syntax evb default-manager { { ip ip-address | ipv6 ipv6-address | name name } [ port port-number ] | local-server } undo evb default-manager Default The default VSI manager is not specified. Views System view Predefined user roles network-admin Parameters ip ip-address: Specifies the IPv4 address of the default VSI manager. -
Page 22: Evb Mac-Learning Forbidden
Predefined user roles network-admin Usage guidelines Do not enable EVB on a member port of an aggregation group, or add a member port with EVB • enabled into an aggregation group. Otherwise, an error message appears. • Restore all default settings for an interface before enabling EVB on the interface. A default S-channel is created on an interface after EVB is enabled on the interface, with both SCID •... -
Page 23: Evb Reflective-Relay
Usage guidelines For an S-channel with the RR mode disabled, do not disable its MAC address learning function. • Otherwise, the EVB bridge might fail to forward traffic from VMs on the EVB station. After you disable the MAC address learning function for an S-channel, packets with an unknown •... -
Page 24: Evb S-Channel
# Enable the RR mode on Schannel-Aggregation 1:10. <Sysname> system-view [Sysname] interface schannel-aggregation 1:10 [Sysname–Schannel-Aggregation1:10] evb reflective-relay evb s-channel Use evb s-channel to create an S-channel on an interface. Use undo evb s-channel to remove an S-channel on an interface. Syntax evb s-channel channel-id service-vlan svlan-id undo evb s-channel channel-id... -
Page 25: Evb Vdp Timer Keepalive Exponent
Examples # Create an S-channel on Ten-GigabitEthernet 1/0/1, with the SCID 10 and SVID 5. <Sysname> system-view [Sysname] interface ten-gigabitethernet 1/0/1 [Sysname-Ten-GigabitEthernet1/0/1] evb s-channel 10 service-vlan 5 # Create an S-channel on Bridge-Aggregation 1, with the SCID 10 and SVID 5. <Sysname>... -
Page 26: Evb Vdp Timer Resource-Wait-Delay Exponent
Table 7 Values for VDP keepalive time VDP keepalive exponent Calculated value (seconds) Result value (seconds) 4.75136 4.91520 5.24288 5.89824 7.20896 9.83040 15.07328 25.55904 46.530056 88.47360 172.35968 340.13184 675.67616 1346.7648 1347 2688.94208 2689 5373.29664 5374 10742.00576 10743 21479.424 21480 Examples # Configure the VDP keepalive exponent on Ten-GigabitEthernet 1/0/1 as 23. - Page 27 Default The VDP resource-wait-delay exponent is 20. Views Layer 2 Ethernet interface view, Layer 2 aggregate interface view Predefined user roles network-admin Parameters value: Specifies a VDP resource-wait-delay exponent in the range of 15 to 31. Usage guidelines The value for VDP response-wait-delay time is expressed by the following equation: VDP response-wait-delay time (seconds) = 2 ×...
-
Page 28: Evb Vsi
<Sysname> system-view [Sysname] interface bridge-aggregation 1 [Sysname-Bridge-Aggregation1] evb vdp timer resource-wait-delay exponent 23 evb vsi Use evb vsi to create a VSI interface or VSI aggregate interface. Use undo evb vsi to remove a VSI interface or VSI aggregate interface. Syntax evb vsi vsi-local-id { association | pre-association } undo evb vsi vsi-local-id... -
Page 29: Evb Vsi Active
[Sysname-S-Channel1/0/1:10] evb vsi 1 association # Create a VSI aggregate interface on Schannel-Aggregation 1:10, with VSI local ID 1 and the association property. <Sysname> system-view [Sysname] interface schannel-aggregation 1:10 [Sysname–Schannel-Aggregation1:10] evb vsi 1 association Related commands evb s-channel • evb vsi filter •... -
Page 30: Evb Vsi Filter
Related commands evb vsi filter evb vsi filter Use evb vsi filter to configure a VSI filter. Use undo evb vsi filter to remove a VSI filter. Syntax evb vsi filter [ group group-id ] vlan vlan-id [ mac mac-address ] undo evb vsi filter [ group group-id ] [ vlan vlan-id [ mac mac-address ] ] Default No VSI filter exists. -
Page 31: Interface
When a filter configured on a VSI interface contains information about a VLAN, you must not • configure the filter on the same VSI interface again or on other VSI interfaces of the S-channel interface. Otherwise, an error message appears. •... -
Page 32: Reset Counters Interface
Views System view Predefined user roles network-admin Parameters s-channel: Specifies an S-channel interface or a VSI interface. schannel-aggregation: Specifies an S-channel aggregate interface or a VSI aggregate interface. interface-number:channel-id: Specifies an S-channel interface or S-channel aggregate interface by its ID. The interface-number argument specifies the interface where the S-channel resides. -
Page 33: Shutdown
Parameters s-channel: Specifies an S-channel interface or a VSI interface. schannel-aggregation: Specifies an S-channel aggregate interface or a VSI aggregate interface. interface-number:channel-id: Specifies an S-channel interface or S-channel aggregate interface by its ID. The interface-number argument specifies the interface where the S-channel resides. The channel-id argument specifies the ID of the S-channel. - Page 34 Views S-channel interface view, S-channel aggregate interface view Predefined user roles network-admin Examples # Shut down S-channel interface S-Channel 1/0/1:10. <Sysname> system-view [Sysname] interface s-channel 1/0/1:10 [Sysname–S-Channel1/0/1:10] shutdown # Shut down S-channel aggregate interface Schannel-Aggregation 1:10. <Sysname> system-view [Sysname] interface schannel-aggregation 1:10 [Sysname–Schannel-Aggregation1:10] shutdown...
-
Page 35: Index
Index B D E I R S evb mac-learning forbidden,14 reflective-relay,15 bandwidth,1 s-channel,16 evb vdp timer keepalive exponent,17 evb vdp timer resource-wait-delay exponent,18 default,1 vsi,20 description,2 evb vsi active,21 display evb cdcp,3 evb vsi filter,22 display evb evb-tlv,4 display evb s-channel,6 display evb summary,7...