Cleaning And Maintenance - Cuisinart SmartPower SPB-7 Series Instruction And Recipe Booklet

button. The blender can be com pletely deactivated and
stopped at any speed by pushing the Off button. You will
need to press the On button again to continue blending.
6. PULSE MODE: While the blender is turned on, you can create
a burst of power for quick, efficient blending, by activating the
pulse function. To do so, first push the Pulse button, which will
cause the pulse indicator light to flash. Next, push and release
the desired speed button. Repeat as desired. You determine
the duration of each pulse. While pulsing, all indicator lights
(the on, the pulse, and the desired speed) will glow. The pulse
function can be used to break apart larger pieces of food or to
control the texture of food when chopping. The pulse function
is also effective in starting the blending process when you do
not want continuous power, or when processing items which
do not require an extended amount of blending.
TO CRUSH ICE: The SmartPower
7.
is strong enough to crush ice without liquid at any speed;
however, for your convenience, we have preset the best speed
for ice crushing. To give you greater control, the ice crush
function automatically operates as a pulse function. To crush
ice, place ice cubes in the blender jar, and place the cover and
the measured pour lid on the blender jar. Press the On button.
Press the Ice Crush button in short pulses until ice is crushed
to desired consistency. See the Recipe Tips section on page 8
for more details.
8. TO DISLODGE FOOD: Use a rubber or plastic spatula to help
remove food lodged around the cutting assembly. DO NOT
USE SPATULA UNTIL YOU HAvE TURNED THE BLENDER
OFF. Replace the cover and measured pour lid and continue
blending, if necessary. Make sure spatula is not inside the
blender jar before blending.
9. WHEN FINISHED BLENDING: Press the Off button and
unplug the blender from the electrical outlet. Never remove
the blender jar from the motor base until the blender is off. Do
not twist locking ring from blender jar when removing jar from
motor base. Simply lift blender jar from motor base. Do not
place hands into blender jar with blender plugged in.
6
Electronic Blender motor
™

CLEANING AND MAINTENANCE

Always unplug your Cuisinart
from the electrical outlet before cleaning. The blender is made of
corrosion-resistant parts which are easy to clean. Before first use
and after every use, clean each part thoroughly. Periodically check
all parts before reassembly. If any part is damaged or blender jar is
chipped or cracked, DO NOT USE BLENDER.
Remove the blender jar from the motor base by lifting straight up
and away. Twist off the locking ring by turning counterclockwise.
Remove the cutting assembly and rubber gasket. Wash in warm
soapy water, rinse, and dry thoroughly.
Place the locking ring in the upper rack of the dishwasher or wash
in warm water.
CAUTION: Handle the cutting assembly carefully. It is SHARP and
may cause injury. Do not attempt to remove blades from cutting
assembly.
Remove the blender jar cover and the measured pour lid. Wash
in warm, soapy water; rinse and dry thoroughly, or place in upper
rack of dishwasher. The blender jar must be washed in warm soapy
water and rinsed and dried thoroughly. The blender jar can also be
placed upside down in dishwasher.
Finally, wipe the motor base clean with a damp cloth to remove
any residue, and dry thoroughly. Never submerge the motor base in
water or other liquid, or place in a dishwasher.
Tip: You may wish to clean your blender cutting assembly as
follows: Squirt a small amount of dishwashing liquid into assem-
bled blender jar and fill halfway with warm water. Run on STIR
for 15 seconds. Repeat, using clean tap water. Empty blender jar
and carefully disassemble parts. Wash cutting assembly, gasket
and locking ring in warm, soapy water. Rinse and dry all parts
thoroughly.
SmartPower Electronic Blender
®
™