Advertisement
Quick Links
INSTALLATION
INSTRUCTIONS
SHOWER |
TILE OVER STAINLESS STEEL SHOWER TRAY
BEFORE YOU BEGIN:
NOTE: Building requirements can vary, local regulations must be checked prior to installation.
Before installing the Stainless Steel shower Tray please read these instructions carefully to
familiarise yourself with the required tools, materials, and installation sequences.
After completing the installation, please leave these instructions for the consumer for further
reference and change of ownership.
TOOLS AND MATERIALS REQUIRED:
1598330-A02-A
707630A-NA TILE OVER SHOWER TRAY 900 X 900
707631A-NA TILE OVER SHOWER TRAY 1000 X 1000
March 2024
Page 1
englefield.co.nz
Advertisement
Related Manuals for Kohler Englefield 707630A-NA
Summary of Contents for Kohler Englefield 707630A-NA
- Page 1 INSTALLATION INSTRUCTIONS SHOWER | TILE OVER STAINLESS STEEL SHOWER TRAY 707630A-NA TILE OVER SHOWER TRAY 900 X 900 707631A-NA TILE OVER SHOWER TRAY 1000 X 1000 BEFORE YOU BEGIN: NOTE: Building requirements can vary, local regulations must be checked prior to installation. Before installing the Stainless Steel shower Tray please read these instructions carefully to familiarise yourself with the required tools, materials, and installation sequences.
- Page 2 TILE OVER Stainless Steel Trays INSTALLATION INSTRUCTIONS A) TILED SHOWER TRAY INSTALLATION (Installation guide steps on page 4 to 8) Detail A Detail B DETAIL A: WET AREA WALL BOARD (9-10mm) FIXING WALL TILES SHOWER NON-SOLVENT TRAY EPOXY GROUT BASED MODIFIED SILICONE ADHESIVE UPSTAND TILE ADHESIVE...
-
Page 3: Floor Construction
TILE OVER Stainless Steel Trays INSTALLATION INSTRUCTIONS B) FLOOR CONSTRUCTION Ensure that is enough space under the floor to install the tray, the waste fitting and the plumbing with an adequate fall of 1.5° (25mm/metre) and continuous flow without bends and restrictions for 1.5 metres from the trap outlet. - Page 4 TILE OVER Stainless Steel Trays INSTALLATION INSTRUCTIONS INSTALLATION GUIDE: 1. Build Shower Area: Determine waste location. a. Determine location of the shower tray. b. Mark the waste hole location. c. Mark the required waste cut-out (142 x 142 mm) and cut. d.
-
Page 5: Tray Installation
Stainless Steel Trays INSTALLATION INSTRUCTIONS TILE OVER b. Tape lightly in position to keep the cap and washer in place during installation. Tape must not obstruct, and must allow the cap to move up freely when the waste is tightened. Tape Keep bottom surface clean to achieve a tight water seal. - Page 6 TILE OVER Stainless Steel Trays INSTALLATION INSTRUCTIONS 4. Build the fall to waste a. Apply primer to the tray surface to prepare for screeding. Leave clear a 170 x 170 mm square around the waste recess for the Waste Tiling Rim to be installed. b.
- Page 7 TILE OVER Stainless Steel Trays INSTALLATION INSTRUCTIONS 6. Install Shower Blocks: a. Install 70 mm Shower Blocks to build the perimeter of the shower. b. Apply Bandage Tape to all joints. Bandage Tape Shower Blocks 7. Apply Waterproofing: Apply the first layer of waterproofing and let it dry. Follow manufacturer’s recommendations. Carefully apply the waterproofing on the Stainless steel tray around the waste, ensure the waste is kept clean of spillage.
-
Page 8: Care And Maintenance
Cleaners of gritty or abrasive nature should never be used. Regularly clean the waste to ensure correct operation. CONTACT AND WARRANTY INFORMATION NEW ZEALAND AUSTRALIA Kohler New Zealand Limited 0800 100 382 info@englefield.co.nz englefield.co.nz englefield.com Page 8...