The use of non-OEM replacement parts will void (or negate) ATEX Pulse output or Intergral Solenoid Not Available For All Pump Models See Explanation of Pump Nomenclature / ATEX Details Page agency certifications, including CE, ATEX, CSA, 3A and EC1935 compliance (Food Contact Materials). Warren Rupp, Inc. cannot ensure nor warrant non-OEM parts to meet the stringent requirements of the certifying agencies.
Page 3
Table of Contents Explanation of Pump Nomenclature Your Model #: S __ ____ ____ SECTION 1: PUMP SPECIFICATIONS ....1 (fill in from pump nameplate) • Explanation of Nomenclature • Performance Pump Pump Check Design Wetted Diaphragm/ Check Valve Non-Wetted Porting Pump Pump Brand...
Performance Dimensional Drawings S1F METALLIC S1F Metallic - NPT MODEL S1F Metallic Performance Curve SUCTION/DISCHARGE PORT SIZE Performance based on the following: elastomer fitted pump, flooded suction, water at ambient conditions. Dimensions in inches (mm dimensions in brackets). Dimensional Tolerance:±1/8" (± 3mm) •...
Dimensional Drawings Principle of Pump Operation S1F Metallic - ANSI Flange Air-Operated Double Diaphragm (AODD) pumps are powered by compressed air or nitrogen. Dimensions in inches (mm dimensions in brackets). Dimensional Tolerance:±1/8" (± 3mm) The dimensions on this drawing are for reference only. A certified drawing can be requested if physical dimensions are needed. The main directional (air) control valve distributes ①...
Recommended Installation Guide Troubleshooting Guide Symptom: Potential Cause(s): Recommendation(s): Pump Cycles Once Deadhead (system pressure meets or exceeds air Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero flow. Available Accessories: supply pressure). (Does not apply to high pressure 2:1 units).
Composite Repair Parts Drawing Composite Repair Parts List Item Part Number Description Item Part Number Description 031.179.000 Air Valve Assembly 518.176.156 Manifold, Discharge (Cast Iron Centers Only) 518.176.156E Manifold, Discharge 1" 031.146.000 Air Valve Assembly (BSP Tapered) (Stroke Indicator) 518.176.156W Welded Raised Face 150# 031.147.000 Air Valve Assembly...
The recyclability of SANDPIPER damage the pump, and void factory warranty. 666..FDA Nitrile Diaphragm, products is a vital part of Warren Rupp’s commitment PTFE Overlay, Balls, and Seals to environmental stewardship. **Note: Pumps equipped with these Valve Assemblies are 668..PTFE, FDA Santoprene...
Page 9
Air Distribution Valve Assembly Air Distribution Valve Assembly (Use With Cast Iron Centers Only) Note: cannot be used with integral muffler Option 0. Air Distribution Valve Servicing Air Valve Assembly Parts List Air Distribution Valve Servicing Air Valve Assembly Parts List Item Part Number Description (Use w/Aluminum center sections) See repair parts drawing, remove screws. See repair parts drawing, remove screws.
Air Valve with Stroke Indicator Assembly Pilot Valve Assembly Note: Stroke Indicator is standard on Spill Containment models Air Valve Assembly Parts List Item Part Number Description 031-146-000 Air Valve Assembly 031-143-000 Sleeve and Spool Set w/Pins 095-119-559 Body, Air Valve 132-039-551 Bumper 165-096-559 Cap, Muffler Pilot Valve Servicing Pilot Valve Assembly Parts List 165-156-147 Cap, End...
Intermediate Assembly Diaphragm Service Drawing, with Overlay Torque: 450 In-lbs (50 N-m) PTFE Diaphragm Service Drawing, Non-Overlay Torque: Intermediate Assembly Drawing Intermediate Assembly Parts List 350 In-lbs (39 N-m) for Santoprene and Elastomer diaphragms Step 1: Remove plunger, actuator (25) from center of Item Part Number Description...
Outer plate with a threaded stud, diaphragm, and align with the inner chamber holes. DO NOT LEAVE 219.001.000 Solenoid Coil, 24VDC Warren Rupp’s solenoid shifted, air distribution valve option utilizes electrical an inner plate with through hole. Secure threaded THE ASSEMBLY LOOSE. 219.004.000 Solenoid Coil, 24VAC/12VDC signals to precisely control your SANDPIPERs speed.
Warren Rupp, Inc. (“Warren Rupp”) warrants to the original end-use purchaser that no product sold by Warren Rupp that bears a Warren Rupp brand shall fail under normal use and service due to a defect in material or workmanship within five years from the date of shipment from Warren Rupp’s factory.
ATEX UKEx EU Declaration of Conformity EU Declaration of Conformity Manufacturer: Manufacturer: Warren Rupp, Inc. Warren Rupp, Inc. A Unit of IDEX Corporation A Unit of IDEX Corporation 800 North Main Street 800 North Main Street Mansfi eld, OH 44902 USA Mansfi eld, OH 44902 USA This declaration of conformity is issued under the sole responsibility of the manufacturer. Warren Rupp, Inc. declares that Air Oper- This declaration of conformity is issued under the sole responsibility of the manufacturer. ated Double Diaphragm Pumps (AODD) and Surge Suppressors listed below comply with the requirements of Directive 2014/34/EU Warren Rupp, Inc declares that Air Operated Double Diaphragm Pumps (AODD) and Surge Suppressors listed below comply with the and applicable harmonized standards. requirements of United Kingdom Statutory Instruments 2016 No. 1107 and all the applicable standards. Harmonized Standards: Designated Standards: • EN ISO 80079-36: 2016 • EN ISO 80079-37: 2016 • EN 60079-25: 2010 • EN ISO 80079-36: 2016 • EN ISO 80079-37: 2016 • EN 60079-25: 2010 DEKRA Certifi cation B.V.