Table of Contents
Advertisement
1.0
Safety
•
Safety Labels and Their Locations
SERVICE ACCESS PANEL
IGNITER & FLAME SENSE COMPARTMENT
1. Turn off gas & electricity.
2. Remove cover by lifting top
cover upward and outward.
CAUTION: HOT SURFACE.
KEEP COVER IN PLACE. REMOVE FOR SERVICE ONLY.
F/N: LLTB026
SERVICE ACCESS PANEL
IGNITER & FLAME SENSE COMPARTMENT
1. Disconnect gas & electricity.
2. Remove cover by lifting top
cover upward and outward.
CAUTION: HOT SURFACE.
KEEP COVER IN PLACE. REMOVE FOR SERVICE ONLY.
SERVICE ACCESS PANEL
F/N: LLTB025R
Fan Compartment
WARNING
Avoid Serious Injury, Death, or Property Damage.
California Proposition 65
Maintain Clearances to Combustible to Prevent the Risk of Fire.
!
Clearances to combustibles must be maintained at
all times in order to prevent the ignition of
combustible materials. In locations used for the
storage of combustible materials, signs must be
posted to specify the maximum permissible stacking height to
monoxide, which are known to the
maintain the required clearances from the heater to the
State of California to cause birth
combustibles. Signs must either be posted adjacent to the
defects or other reproductive harm.
heater's thermostats or, in the absence of such thermostats, in a
conspicuous location. Clearances are provided on the heater's
For more information go to
safety label and in the heater's Installation, Operation, and
www.P65Warnings.ca.gov.
Maintenance manual. Product installation and operation must
comply with applicable standards, codes, and regulations. Post
this tag adjacent to the heater's thermostat or controls before
operating the heater.
- INSTALLER: READ AND POST THIS NOTICE -
F/N: LL001 - Clearance Safety Tag
(Affix adjacent to heater's thermostat)
Clearances to Combustibles
Clearance to combustibles is defined as the minimum distance that must exist between the tube surface, or
reflector, and any combustible items (see Figure 1.1). It also pertains to the distance that must be maintained
from moving objects around the tube heater.
•
Clearances to Combustibles
SERVICE ACCESS PANEL
RE-VERBER-RAY INFRA-RED RADIANT TUBE HEATER
LOW-INTENSITY INFRARED HEATER
®
FOR OUTDOOR USE AND INDOOR (Non-Residential) INSTALLATION ONLY.
RADIATEUR À INFRAROUGE À FAIBLE INTENSITÉ
Class IIIA Permanent Label
112671
MODEL NUMBER
SERIAL NUMBER
VERSION
MODEL NO.
NUMÉRO DE MODÈLE
NUMÉRO DE SÉRIE
INPUT BTU/H
FOR USE WITH
MP3-40-115N
YYMMREPCSHIPPE####
01/24
MP-40-150N
155,000 / 150,000 / 98,000
Natural Gas
MAX. HEAT INPUT
MANIFOLD PRESSURE
VOLTAGE
MAX. DEBIT CALORIFIQUE
Volts AC:
115,000
PRESSION A LA TUBULURE D'ALIMENTATION
Manifold Pressure:
3.5
Heater Type
120
BTU/h
INCHES W.C.
VAC
120V - 60Hz
3.5 in.
W.C.P.
C1
MIN. HEAT INPUT
MAXIMUM INLET PRESSURE
14.0
AMPS
MIN. DEBIT CALORIFIQUE
85,000
PRESSION D'ALIMENTATION MAXIMALE
4.8
BTU/h
INCHES W.C.
AMPS - Starting:
Maximum Inlet Pressure:
Minimum Mounting Angle:
TYPE OF GAS
MINIMUM INLET PRESSURE FOR PURPOSE OF ADJ.
PHASE
TYPE DE GAZ
NATURAL
PRESSION D'ALIMENTATION EN GAS MIN. ADMISE
5.0
SINGLE
4.8
14 in.
W.C.P.
INCHES W.C.
0
DEGREES
VENT CATEGORY
ORIFICE SIZE
FREQUENCY
AMPS - Running:
CAT. I OR III
DIM DE L'INJECTEUR
60
ÉVENT CATÉGORIE
Minimum Inlet Pressure:
Maximum Mounting Angle:
Hz
1.1
COMBUSTION CHAMBER
5.0 in.
W.C.P.
45
MIN. MOUNTING ANGLE
DEGREES
TP-26A; 4" Aluminized
MIN. ANGLE DE SUPPORT
0°
Combustion Chamber:
THIS DESIGN COMPLIES WITH STANDARD(S):
MAX. MOUNTING ANGLE
4" Black Coated Aluminized
45°
COMPLES DE CETTE CONCEPTION AVEC LA NORME:
For stainless steel upgrades: The combustion tube is 409 Series stainless steel.
MAX. ANGLE DE SUPPORT
ANSI Z83.20-2016 • CSA 2.34-2016 RADIANT TUBE HEATER
HEATER BUILD TYPE
DESIGN COMPLIES WITH:
C1
ANSI Z83.20b-2004-GAS FIRED LOW INTENSITY INFRA-RED HTR.
Detroit Radiant Products Company
DETROIT RADIANT PRODUCTS COMPANY
Serial No.: 1011XXXXXXXXXX 0001
FOR COMMERCIAL / INDUSTRIAL USE.
21400 HOOVER ROAD - WARREN, MI
21400 Hoover Road
Warren MI
48089
FOR INDOOR USE ONLY.
(586) 756-0950
-
www.drp-co.com
MADE IN U.S.A.
(586) 756-0950 www.reverberray.com
Controls Compartment
16" Burner Tube
This product can
expose you to
chemicals including
lead and carbon
LL001-XM-07/18 (CDS)
WARNING
!
Placement of explosive objects, flammable objects, liquids, and vapors close to
the heater may result in explosion, fire, property damage, serious injury, or death.
Do not store or use explosive objects, liquids, or vapors in the vicinity of the
heater.
MP3-40-115N
SERIAL NUMBER: 2401XXXXXXXXXX 0001
PRODUCTION CODE: MP3-C1
COMPONENT PART NO. DESCRIPTION
CIRCUIT BOARD ......... TP-351A
GAS VALVE ................. TP-3340
GAS INLET................... TP-76
IGNITER ....................... TP-50A
IND. LIGHT #1.............. TP-328
IND. LIGHT #2.............. TP-828
IND. LIGHT #3.............. NONE
:
F/N
LLTB024L
AIR ORIFICE SIZE ....... TP-3014
BURNER ...................... TP-3072
GAS ORIFICE SIZE ..... 8
1ST PRES. SWITCH .... TP-264D
2ND PRES. SWITCH ... TP-260H
WIRING DIAGRAM ...... LLWTXXX
Please contact the factory for assistance, parts information and/or list prices at 586-756-0950 or visit store.reverberray.com
Burner Control Box Component Label
(located inside the center compartment lid)
MODEL NUMBER
NUMÉRO DE MODÈLE
MP3-40-115N
MAX. HEAT INPUT
MAX. DEBIT CALORIFIQUE
MIN. HEAT INPUT
MIN. DEBIT CALORIFIQUE
TYPE OF GAS
TYPE DE GAZ
VENT CATEGORY
ÉVENT CATÉGORIE
COMBUSTION CHAMBER
THIS DESIGN COMPLIES WITH STANDARD(S):
COMPLES DE CETTE CONCEPTION AVEC LA NORME:
ANSI Z83.20-2016 • CSA 2.34-2016 RADIANT TUBE HEATER
Detroit Radiant Products Company
21400 Hoover Road
(586) 756-0950 www.reverberray.com
Combustion Chamber
AVOID EQUIPMENT FAILURE
THIS 10 FT. TUBE IS THE
COMBUSTION CHAMBER.
The combustion chamber utilizes either 409
stainless, titanium alloy or aluminized steel -
depending on the model number of your heater.
Rotate the tube's welded seam to bottom.
Consult the manual(s) for further details.
(150,000 - 200,000 BTU/h models only)
4
01/24
VERSION
None
OPTIONS
BILL OF MATERIALS
COMPONENT PART NO. DESCRIPTION
Fenwal
INDUCER FAN ............. TP-55A
1/20 hp Inducer Assy
36J54-224-N
POWER ENTRY........... 333
BX Conduit Connector
7/8" FC
RELAY.......................... N/A
N/A
Glo-Bar
STARTER TUBE .......... TP-3380
4" Gen.
TERMINAL BLOCK ...... NONE
120 V Amber Light
N/A
24V Amber Light
TRANSFORMER.......... TP-826
40VA
N/A
WIRE HARNESS.......... TP-352A
Wire Harness
MODEL SPECIFIC DATA
TUBE & REFLECTOR PARTS
1 11/16"
BAFFLE ........................ TP-65I
5
Green
COMB. TUBE ............... TP-26A
4" Aluminized
DMS
HANGERS.................... TP-19B
4" Galv w/spring
IS22010051F5166
REFLECTORS ............. TP-20C
10' Aluminum
RADIANT TUBE ........... TP-26A
PS
4" Aluminized
Rev. 1
TUBE CLAMP .............. TP-21B
4" Galv Clamp
LOW-INTENSITY INFRARED HEATER
RADIATEUR À INFRAROUGE À FAIBLE INTENSITÉ
SERIAL NUMBER
NUMÉRO DE SÉRIE
YYMMREPCSHIPPE####
MANIFOLD PRESSURE
VOLTAGE
115,000
3.5
PRESSION A LA TUBULURE D'ALIMENTATION
BTU/h
INCHES W.C.
MAXIMUM INLET PRESSURE
AMPS
14.0
85,000
PRESSION D'ALIMENTATION MAXIMALE
BTU/h
INCHES W.C.
MINIMUM INLET PRESSURE FOR PURPOSE OF ADJ.
PHASE
5.0
NATURAL
PRESSION D'ALIMENTATION EN GAS MIN. ADMISE
INCHES W.C.
ORIFICE SIZE
FREQUENCY
CAT. I OR III
DIM DE L'INJECTEUR
MIN. MOUNTING ANGLE
TP-26A; 4" Aluminized
MIN. ANGLE DE SUPPORT
MAX. MOUNTING ANGLE
MAX. ANGLE DE SUPPORT
HEATER BUILD TYPE
FOR COMMERCIAL / INDUSTRIAL USE.
Warren MI
48089
FOR INDOOR USE ONLY.
MADE IN U.S.A.
Radiant Tube(s)
INSTALLER
!
F/N: LLTB004
(orange)
MP3
Series
Rating
Plate
112671
VERSION
01/24
120
VAC
4.8
SINGLE
60
Hz
0°
45°
C1
Advertisement
Table of Contents
