Clearance To Combustibles - Re-Verber-Ray DX3-20-50 Insert Manual

1.0 Safety • Safety Labels and Locations • Clearance to Combustibles
SERVICE ACCESS PANEL
IGNITER & FLAME SENSE COMPARTMENT
1. Turn off gas & electricity.
2. Remove cover by lifting top
cover upward and outward.
CAUTION: HOT SURFACE.
KEEP COVER IN PLACE. REMOVE FOR SERVICE ONLY.
F/N: LLTB026
SERVICE ACCESS PANEL
IGNITER & FLAME SENSE COMPARTMENT
1. Disconnect gas & electricity.
2. Remove cover by lifting top
cover upward and outward.
CAUTION: HOT SURFACE.
KEEP COVER IN PLACE. REMOVE FOR SERVICE ONLY.
SERVICE ACCESS PANEL
F/N: LLTB025R
Fan Compartment
F/N: LL01 - Clearance Safety Tag
(Affix adjacent to heater's thermostat)

Clearance to Combustibles

Clearance to combustibles is defined as the minimum distance that must exist between the tube surface,
or reflector, and any combustible items (see Figure 1.1). It also pertains to the distance that must be
maintained from moving objects around the tube heater. When installing the tube heater system, clearances
to combustibles for the model tube heater and configuration must be maintained. Refer to Chart 1.1 to
determine the required distances for your model.
SERVICE ACCESS PANEL
F/N: LLTB024L
RE-VERBER-RAY INFRA-RED RADIANT TUBE HEATER
®
FOR INDOOR (Non-Residential) INSTALLATION ONLY.
Class IIIA Permanent Label
MODEL NO. INPUT BTU/H FOR USE WITH
DET-40-125N(-3) 125,000 / 95,000 Natural Gas
HL3 DX3
Volts AC: Manifold Pressure: Heater Type
120VAC - 60Hz 3.5 in. Inches W.C.P. C1
AMPS - Starting: Maximum Inlet Pressure: Minimum Mounting Angle:
1.7
14 in. Inches W.C.P. 0 DEGREES
AMPS - Running:
Minimum Inlet Pressure: Maximum Mounting Angle:
1.1
5.0 in. Inches W.C.P. 45 DEGREES
Combustion Chamber:
4" Black Coated Aluminized
DESIGN COMPLIES WITH:
ANSI Z83.20b-2004-GAS FIRED LOW INTENSITY INFRA-RED HTR.
DETROIT RADIANT PRODUCTS COMPANY
Serial No.: 1208XXXXXXXXXX 0001
21400 HOOVER ROAD - WARREN, MI
(586) 756-0950 - www.drp-co.com
Controls Compartment
16" Burner Tube
WARNING
!
Placement of explosive objects, flammable objects, liquids and vapors close to
the heater may result in explosion, fire, property damage, serious injury or death.
Do not store or use explosive objects, liquids or vapor in the vicinity of the heater.
DX HL-40-125N(-3)
Production Code:
DX3 HL3-125
Version:
7.08
Data on this label is for the model shown on this label. If your heater has been converted,
this information is not accurate. Please contact the factory for assistance.
BURNER COMPONENTS:
(Specify TP-#'s)
Gas Valve: 36G54-224-N 840A
Circuit Board: 35-66 851B
Wire Harness: 3 PCS Harness 3252
N.O. Switch: None N/A
N.O. VL Orifice: None
N.C. Switch: None N/A
N.C. VL Orifice: None
Diff Switch: IS22010051F5166
264E
Diff VL Orifice: Grey (+ / -)
Igniter: Norton 50
Burner: Mid 201B
16" Tube: 4" Gen. 380
Ind. Lights: Yellow - 24V 828
HEATER Orifice Type: C1
TYPE:
Gas:
TP-204# 19
C1
Air:
TP-44# 1 5/16" 1 7/16"
For parts replacement information, contact factory at 586-756-0950 or visit www.drp-co.com/parts.
Burner Control Box Component Label
(located inside the center compartment lid)
RE-VERBER-RAY INFRA-RED RADIANT TUBE HEATER
®
FOR OUTDOOR USE AND INDOOR (Non-Residential) INSTALLATION ONLY.
Class IIIA Permanent Label
MODEL NO. INPUT BTU/H
HL-40-125N(-3) 125,000 / 95,000
DX
Volts AC: Manifold Pressure:
120V - 60Hz 3.5 in.
AMPS - Starting:
Maximum Inlet Pressure:
4.8
14 in.
AMPS - Running:
Minimum Inlet Pressure:
1.1
5.0 in.
Combustion Chamber:
4" Black Coated Aluminized
DESIGN COMPLIES WITH:
ANSI Z83.20b-2004-GAS FIRED LOW INTENSITY INFRA-RED HTR.
DETROIT RADIANT PRODUCTS COMPANY
21400 HOOVER ROAD - WARREN, MI
(586) 756-0950 - www.drp-co.com
Combustion Chamber
INSTALLER
!
AVOID EQUIPMENT FAILURE
THIS 10 FT. TUBE IS THE
COMBUSTION CHAMBER.
The combustion chamber utilizes either 409
stainless, titanium alloy or aluminized steel -
depending on the model number of your heater.
Rotate the tube's welded seam to bottom.
Consult the manual(s) for further details.
F/N: LLTB004
(150,000 - 200,000 Btu/h models only)
4
DX3 Series
Serial No.: 0804XXXXXXXXXX 0001
Stock:
None
Add-On:
N/A
Diag. Light: On Circuit Board
Term. Block: None N/A
Transformer: 40 VA 826
Fan: Fasco Lg. 55A
Alt. Fan: 50Hz - 120V 55B
Alt. Fan Usage: When Specified
Relay: Picker x2 1325
Filter:
None N/A
24 Volt In: 3 T-plug 832
120 Volt In: 6' Blk. Cord 333
Gas In: 7/8" FC 83
Extra VL Orifice: None
Internal Use Only:
C2 C3
Electric: Special 1:
19 19 LLWT038 17
Tag:
1 5/16" None Special 2: 1 7/16"
Rating
Plate
FOR USE WITH
Natural Gas
Heater Type
W.C.P. C1
Minimum Mounting Angle:
W.C.P. 0 DEGREES
Maximum Mounting Angle:
W.C.P. 45 DEGREES
For stainless steel upgrades: The combustion tube is 409 Series stainless steel.
Serial No.: 0807XXXXXXXXXX 0001
Radiant Tube(s)
(orange)