Advertisement
Quick Links
Advertisement
Related Manuals for HAKO 7180.50
Summary of Contents for HAKO 7180.50
- Page 1 Assembly and Instruction Manual Pre-sweep suction unit (7180.50)
- Page 2 Hako service centre or es. This machine is intended for com- sure that only original spare parts are a workshop authorised by Hako.
- Page 3 Maintenance work must report together with the consignment and safety requirements of the EC be carried out by an authorised Hako note to our authorised dealer. Directives (see Declaration of service centre and confirmed in the Conformity).
-
Page 4: Safety Information
Safety information Safety information Safety and warning symbols All texts that affect your safety, the safety of the machine and the environ- ment are marked with these symbols in the operating manual: Symbol Damage for... Definition Safety instructions persons or property Safety instructions for avoiding dangerous situations as a result of failure to comply with instructions or prescribed work procedures. - Page 5 Safety information Safety instructions Maintenance instructions Please observe the safety instructions • Shaking the filter is only permitted of the relevant machine in the with the dirt hopper inserted. applicable operating manual. • Only tip out the contents of the dirt The following safety instructions also hopper from a low height in order to refer to the pre-sweep suction unit.
- Page 6 Safety information Labels on the pre-sweep Side brush wear compensation suction unit (Fig. 1/4) The following safety and instruction labels are affixed to the vehicle in a clearly visible and legible location. Renew missing or illegible labels immediately. Company logo (Fig. 1/1) Shaking system (Fig.
- Page 7 Pre-sweep suction unit installation Pre-sweep suction unit installation Parts list 1x complete pre-sweep suction unit (Fig. 2/1) Assembly Requirements: Pre-sweep suction unit set-up components (7180.55) are fitted to the basic machine. Assembly: 1. Slide the pre-sweep suction unit as far as the swivel bracket on the machine in a central position.
- Page 8 Pre-sweep suction unit installation 2.2.1 Check settings: If the pre-sweep suction unit is attached to the machine and the lever is in the sweeping position (Pos. 1) (Fig. 3/1), the frame must be aligned parallel to the floor. 2.2.2 Correct setting: If this is not the case, the following steps must be taken: 1.
-
Page 9: Operation
Operation Operation Stop sweeping operation 3.3.1 Parking the pre-sweep 1. Press the Pre-sweep suction unit suction unit Sweeping operation (Fig. 4/1) button on the control panel. 1. Unplug the plug at the machine-side 2. Move the lever of the pre-sweep unit and plug into the retaining hole Do not use the pre-sweep from pos. -
Page 10: Technical Data
Technical data Technical data Machine length Height of machine Machine width (above swivel bracket) 1220 Working width 1300 Cylindrical brush width Cylindrical brush, minimum diameter Cylindrical brush speed Sweeping level width 45±10 Side brush diameter Side brush speed Theoretical sweeping capacity m²/h 10400 Dirt hopper volume (maximum load 20 kg) -
Page 11: Maintenance And Servicing
Daily and weekly maintenance and re- pair work can be undertaken by a driver trained for this, all further Hako system maintenance work may be undertaken only by trained and qualified personnel. Please contact your nearest Hako ser- vice centre or authorised Hako dealer. - Page 12 Maintenance and Servicing Maintenance plan Hako system maintenance by the customer The following maintenance work is performed by the customer. Intervals Activity Daily Weekly Clean the cylindrical brush compartment Clean the plate filter using the shaking system Empty the dirt hopper...
- Page 13 Maintenance and Servicing Dirt hopper 5.2.1 Emptying the dirt hopper Check the fill level of the dirt hopper at regular intervals (max. load 20 kg) and empty if necessary. 1. Turn off the machine. 2. Pull the dirt hopper (Fig. 6/1) up- wards using the handle (Fig.
- Page 14 Maintenance and Servicing Filter 5.3.1 Shaking the filter Clean the filter multiple times per day using the shaking system (Fig. 6/4). To clean the filter, pull out the lever of the shaking system several times and slide back in again. 5.3.2 Cleaning the filter 1.
- Page 15 Maintenance and Servicing Cylindrical brush 5.4.2 Replacing the cylindrical brush: 5.4.1 Cleaning the cylindrical brush Inspect the cylindrical brush once per and the cylindrical brush week and replace if wear is present. compartment Follow instructions 1.-3. under Cleaning Inspect the cylindrical brush (Fig. 8/1) the cylindrical brush and the cylindrical for soiling daily.
- Page 16 Maintenance and Servicing 5.4.3 Adjusting the sweeping level 5.4.4 Replacing the sealing strips In the event of brush wear and after of the cylindrical brush replacing the cylindrical brush, the compartment sweeping level (Fig. 8/1) must be The sealing strips must be in perfect readjusted.
- Page 17 Maintenance and Servicing Side brushes 5.5.1 Changing the side brush Inspect the side brushes once per week and replace if wear is present. 1. Switch off the machine and remove the dirt hopper (Fig. 10/1). 2. Remove both M6x16 flanged button head bolts, the brush adjuster and the cover (Fig.
- Page 18 EC Declaration of Conformity (corresponding to the EC Directive 2006/42/EC) Hako GmbH For the relevant implementation of Name of the person authorised for Hako to compile the technical file: Hamburger Straße 209-239 the safety and health requirements mentioned in the Directives, the fol- D-23843 Bad Oldesloe Ludger Lüttel...
- Page 20 Advanced Technology for a Cleaner, Better Environment · · · · Hako GmbH Head Office Hamburger Str. 209-239 23843 Bad Oldesloe Germany · Phone +49 4531 806-0 Fax +49 4531 806-338...