Table of Contents
Advertisement
EN
TESTING OF THE UNIT / INFORMATION ON PRODUCT LIABILITY / GUARANTEE DECLARATION
TESTING OF THE UNIT
For safety reasons, we would recommend having the device
checked by an expert as required but at least every 12 months
to ensure that it can continue to operate safely.
In the case of unused devices, the check can be postponed
until they are next started up.
All (potentially deviating) national inspection and mainte-
nance regulations must also be observed.
If you have any questions, please contact the customer service
team at Wagner.
IMPORTANT INFORMATION ON PRODUCT LIABILITY
According to an EU directive, the manufacturer is only liable
without limitation for faults in the product if all parts come
from the manufacturer or have been approved by the manu-
facturer and have been mounted to the device and are operat-
ed properly. If third-party accessories or spare parts are used,
the manufacturer is exonerated wholly or partly from his/her
liability if use of the third-party accessories or spare parts have
caused a defect in the product. In extreme cases, the relevant
authorities can completely prohibit using the entire device.
With original WAGNER accessories and spare parts, compli-
ance with all safety regulations is guaranteed.
NOTE ON DISPOSAL
In observance of the European Directive 2002/96/EC on waste
electrical and electronic equipment and implementation in
accordance with national law, this product is not to be dispo-
sed of together with household waste material but must be
recycled in an environmentally friendly way!
Wagner or one of our dealers will take back your used Wagner
waste electrical or electronic equipment and will dispose of
it for you in an environmentally friendly way. Please ask your
local Wagner service centre or dealer for details or contact us
direct.
3 + 2 YEAR GUARANTEE ON THIS WAGNER CRAFTSMAN
PRODUCT (Status 03.03.2022)
WAGNER exclusively provides the commercial buyer who has
purchased the product from an authorised specialist dealer
(hereinafter referred to as the „Customer") with a warranty
for the products listed on the Internet at https://go.wagner-
group.com/3plus2-info in addition to the statutory warranty
regulations, unless there is a warranty exclusion.
The warranty period for WAGNER products (devices) in the
craftsmen's sector is 36 months and begins with the date of
purchase of the initial purchase. This warranty period is exten-
ded by a further 24 months if the product is registered within
52
28 days of purchase on the Internet at https://go.wagner-
group.com/3plus2.
In cases of commercial rental, industrial use (e.g. use in shift
operation) or equivalent use, the warranty period is 12 months
due to the significantly higher load. We reserve the right to
carry out a check in individual cases and refuse the warranty
where necessary.
If any material, machining or performance defects are identi-
fied in the device within the warranty period, then the warran-
ty claims must be made immediately and within a period of no
more than 2 weeks following discovery of the defect.
The detailed guarantee conditions can be obtained on
request from our authorised WAGNER partners (see website
or operating instructions) or in text form on our website:
https://go.wagner-group.com/pf-warranty-conditions
EU Declaration of conformity
We declare under sole responsibility that this product
conforms to the following relevant stipulations:
2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU
Applied harmonised norms:
EN ISO 12100, EN 1953, EN 62841-1, EN IEC 55014-1,
EN IEC 55014-2, EN IEC 61000-3-2, EN 61000-3-3
The EU declaration of conformity is enclosed with the
product. If required, it can be re-ordered using order number
2448573.
UKCA Declaration of conformity
We declare under sole responsibility that this product
conforms to the following relevant regulations:
Supply of Machinery (Safety) Regulations 2018
Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
The Waste Electrical and Electronic Equipment Regulations
2013
Applied harmonised standards
BS EN ISO 12100, BS EN 62841-1, BS EN 1953,
BS EN IEC 55014-1, BS EN IEC 55014-2, BS EN IEC 61000-3-2,
BS EN 61000-3-3
Super Finish 21 Pro
Subject to modifications
Advertisement
Table of Contents
