IEI Technology IMB-ADL-H610 User Manual
  1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Motherboard
  5. IMB-ADL-H610
  6. User manual

IEI Technology IMB-ADL-H610 User Manual

Micro atx motherboard supports lga1700 12th/13th gen. intel core i9/i7/i5/i3, pentium and celeron processor, ddr4, triple independent display, dual gbe lan, usb 3.2, sata 6gb/s, and rohs
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IMB-ADL-H610 Micro ATX Motherboard
MODEL:
IMB-ADL-H610
Micro ATX Motherboard Supports LGA1700 12th/13th Gen.
Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® Processor,
DDR4, Triple Independent Display, Dual GbE LAN, USB 3.2,
SATA 6Gb/s, and RoHS
Rev. 1.00 – June 21, 2023
User Manual
Page 1

Advertisement

Table of Contents
loading

Related Manuals for IEI Technology IMB-ADL-H610

Summary of Contents for IEI Technology IMB-ADL-H610

  • Page 1 IMB-ADL-H610 Micro ATX Motherboard MODEL: IMB-ADL-H610 Micro ATX Motherboard Supports LGA1700 12th/13th Gen. Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® Processor, DDR4, Triple Independent Display, Dual GbE LAN, USB 3.2, SATA 6Gb/s, and RoHS User Manual Page 1 Rev. 1.00 – June 21, 2023...
  • Page 2 IMB-ADL-H610 Micro ATX Motherboard Revision Date Version Changes June 21, 2023 1.00 Initial release Page 2...
  • Page 3 IMB-ADL-H610 Micro ATX Motherboard Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
  • Page 4 IMB-ADL-H610 Micro ATX Motherboard Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.

  • Page 5: Table Of Contents

    PTIONAL TEMS 3 CONNECTORS ......................26 3.1 P ..............27 ERIPHERAL NTERFACE ONNECTORS 3.1.1 IMB-ADL-H610 Layout ................... 27 3.1.2 Peripheral Interface Connectors ..............28 3.1.3 External Interface Panel Connectors ............... 29 3.2 I ..............30 NTERNAL ERIPHERAL ONNECTORS 3.2.1 CPU 12V Power Connector ................30 3.2.2 ATX Power Connector ..................
  • Page 6 IMB-ADL-H610 Micro ATX Motherboard 3.2.10 Audio Connector for IEI AC-KIT-888S kit ............. 41 3.2.11 Front Panel Connector ................... 42 3.2.12 I C Connector ....................43 3.2.13 SMBus Connector ..................44 3.2.14 LAN link LED Connector ................45 3.2.15 M.2 M-key (2280) slot ..................46 3.2.16 PCIe x1 Slots ....................
  • Page 7 IMB-ADL-H610 Micro ATX Motherboard 4.9 D ....................79 RIVER OWNLOAD 5 BIOS ..........................81 5.1 I ......................82 NTRODUCTION 5.1.1 Starting Setup ....................82 5.1.2 Using Setup ...................... 83 5.1.2.1 Keyboard Navigation ................83 5.1.2.2 Touch Navigation ..................84 5.1.3 Getting Help ..................... 85 5.1.4 Unable to Reboot after Configuration Changes ..........
  • Page 8 IMB-ADL-H610 Micro ATX Motherboard 5.4.2 PCH-IO Configuration .................. 130 5.4.2.1 PCI Express Configuration ..............134 5.4.2.2 PCIE3, PCIE2, PCIE4, M2_M1 ............. 135 5.4.2.3 SATA Configuration ................137 5.4.2.4 HD Audio Configuration ................. 138 5.5 S ....................... 139 ECURITY 5.6 B ........................
  • Page 9 IMB-ADL-H610 Micro ATX Motherboard List of Figures Figure 1-1: IMB-ADL-H610 ......................14 Figure 1-2: Connectors ........................16 Figure 1-3: IMB-ADL-H610 Dimensions (mm) ................17 Figure 1-4: Data Flow Diagram ....................18 Figure 3-1: Peripheral Interface Connectors ................27 Figure 3-2: ATX CPU 12V Power Connector Location ..............30 Figure 3-3: ATX Power Connector Location ................31...
  • Page 10 IMB-ADL-H610 Micro ATX Motherboard Figure 3-28: HDMI Connector ......................60 Figure 3-29: DP Connector ......................60 Figure 3-30: Dual DB-9 .........................61 Figure 3-31: USB3.2 And RJ45 LAN Connector ................63 Figure 3-32: External LAN 2.5GbE Connector and USB 3.2 Gen 2 Type A ......63 Figure 4-1: Disengage the CPU Socket Load Lever ..............68...
  • Page 11 IMB-ADL-H610 Micro ATX Motherboard List of Tables Table 1-1: IMB-ADL-H610 Specifications ...................21 Table 2-1: Packing List .........................24 Table 2-2: Optional Items ......................25 Table 3-1: Peripheral Interface Connectors ................29 Table 3-2: Rear Panel Connectors ....................29 Table 3-3: ATX CPU 12V Power Connector Pinouts ..............30 Table 3-4: ATX Power Connector Pinouts..................32...
  • Page 12 IMB-ADL-H610 Micro ATX Motherboard Table 3-29: RJ45 LAN Connector ....................62 Table 3-30: External USB 3.2 Connector ..................62 Table 3-31:External LAN 2.5GbE Connector Pinouts ...............64 Table 3-32: External Dual USB 3.2 Gen 2 Connector Pinouts ..........64 Table 4-1: AT/ATX Power Mode Switch Settings ...............74 Table 4-2: Clear CMOS Jumper Pinouts ..................75...

  • Page 13: Introduction

    IMB-ADL-H610 Micro ATX Motherboard Chapter Introduction Page 13...

  • Page 14: Ntroduction

    1.1 Introduction Figure 1-1: IMB-ADL-H610 The IMB-ADL-H610 is a micro ATX motherboard. It accepts a Socket LGA1700 Intel® 12/13th Generation Core™ i9/i7/i5/i3, Pentium® and Celeron® processor and supports two 288-pin 3200 MHz dual-channel DDR4 SDRAM DIMM modules up to 64 GB. The integrated Intel®...

  • Page 15: Features

    IMB-ADL-H610 Micro ATX Motherboard 1.2 Features Some of the IMB-ADL-H610 motherboard features are listed below: ▪ Micro ATX form factor ▪ generation LGA1700 Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processor supported ▪ Intel® H610/H610E chipset ▪ Two 288-pin 3200 MHz dual-channel unbuffered DDR4 SDRAM DIMM slots support up to 64 GB memory Intel®...

  • Page 16: Connectors

    IMB-ADL-H610 Micro ATX Motherboard 1.3 Connectors The connectors on the IMB-ADL-H610 are shown in the figure below. Figure 1-2: Connectors Page 16...

  • Page 17: Dimensions

    IMB-ADL-H610 Micro ATX Motherboard 1.4 Dimensions The main dimensions of the IMB-ADL-H610 are shown in the diagram below. Figure 1-3: IMB-ADL-H610 Dimensions (mm) Page 17...

  • Page 18: Data Flow

    IMB-ADL-H610 Micro ATX Motherboard 1.5 Data Flow Figure 1-4 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-4: Data Flow Diagram Page 18...

  • Page 19: Technical Specifications

    IMB-ADL-H610 Micro ATX Motherboard 1.6 Technical Specifications The IMB-ADL-H610 technical specifications are listed below. 747 H Specification/Model IMB-ADL-H610 Micro ATX Form Factor generation LGA1700 Intel® Core™ i9/i7/i5/i3, CPU Supported Pentium® and Celeron® CPU Intel® H610/H610E Chipset Two 288-pin 3200 MHz dual-channel unbuffered DDR4 Memory SDRAM DIMMs supported (system max.
  • Page 20 IMB-ADL-H610 Micro ATX Motherboard One 12-bit digital I/O Digital I/O Two RJ-45 GbE ports Ethernet One 4-pin CPU smart fan connector Two 4-pin system smart fan connectors One 14-pin header (power LED, HDD LED, speaker, power Front Panel button, reset button)

  • Page 21: Table 1-1: Imb-Adl-H610 Specifications

    IMB-ADL-H610 Micro ATX Motherboard 244 mm x 244 mm Dimensions Weight (GW/NW) 1200 g/700 g Table 1-1: IMB-ADL-H610 Specifications Page 21...

  • Page 22: Packing List

    IMB-ADL-H610 Micro ATX Motherboard Chapter Packing List Page 22...

  • Page 23: Anti-Static Precautions

    Only handle the edges of the PCB: Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the IMB-ADL-H610 is unpacked, please do the following: ▪ Follow the anti-static guidelines above.

  • Page 24: Packing List

    If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the IMB-ADL-H610 was purchased from or contact an IEI sales representative directly by sending an email to sales@ieiworld.com.

  • Page 25: Optional Items

    IMB-ADL-H610 Micro ATX Motherboard 2.4 Optional Items The following are optional components which may be separately purchased: Item and Part Number Image Dual port USB cable with bracket, 300mm, P=2.54 (P/N: 19800-003100-100-RS) Realtek ALC888S 7.1 Channel HD Audio peripheral board, RoHS...

  • Page 26: Connectors

    IMB-ADL-H610 Micro ATX Motherboard Chapter Connectors Page 26...

  • Page 27: Peripheral Interface Connectors

    IMB-ADL-H610 Micro ATX Motherboard 3.1 Peripheral Interface Connectors This chapter details all the peripheral interface connectors. 3.1.1 IMB-ADL-H610 Layout The figures below show all the peripheral interface connectors. Figure 3-1: Peripheral Interface Connectors Page 27...

  • Page 28: Peripheral Interface Connectors

    IMB-ADL-H610 Micro ATX Motherboard 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type Label 3-pin Molex power AT/ATX power mode setting J_ATX_AT1 connector Clear CMOS jumper 4-pin Push button J_CMOS1 Flash descriptor security...

  • Page 29: External Interface Panel Connectors

    IMB-ADL-H610 Micro ATX Motherboard Connector Type Label SATA1, SATA2, SATA 6Gb/s connectors 8-pin connector SATA3, SATA4 SMBus connector 4-pin wafer J_SMB1 Flash SPI ROM connector 6-pin wafer JSPI1 Flash EC ROM connector 8-pin header JEC1 Internal USB 2.0 connector 8-pin header...

  • Page 30: Internal Peripheral Connectors

    IMB-ADL-H610 Micro ATX Motherboard 3.2 Internal Peripheral Connectors The section describes all of the connectors on the IMB-ADL-H610. 3.2.1 CPU 12V Power Connector CN Label: CPU12V1 CN Type: 8-pin Molex power connector, P=4.2mm CN Location: See Figure 3-2 CN Pinouts: See Table 3-3 This connector provides power to the CPU.

  • Page 31: Atx Power Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.2 ATX Power Connector CN Label: ATX1 CN Type: 24-pin connector, p=4.2 mm CN Location: See Figure 3-3 CN Pinouts: See Table 3-4 The ATX power connector connects to an ATX power supply. Figure 3-3: ATX Power Connector Location PIN NO.

  • Page 32: Battery Connector

    Dispose of used batteries according to instructions and local regulations. NOTE: It is recommended to attach the RTC battery onto the system chassis in which the IMB-ADL-H610 is installed. CN Label: BAT2 CN Type: 2-pin header...

  • Page 33: Figure 3-4: Rtc Battery Connector Location

    IMB-ADL-H610 Micro ATX Motherboard Figure 3-4: RTC Battery Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION VBATT Table 3-5:RTC Battery Connector Pinouts Page 33...

  • Page 34: Digital Input / Output Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.4 Digital Input / Output Connector CN Label: DIO1 CN Type: 14-pin header, p=2.0 mm CN Location: See Figure 3-5 CN Pinouts: See Table 3-6 The Digital I/O connector provides programmable input and output for external devices.

  • Page 35: Ec Debug Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.5 EC Debug Connector CN Label: DEBUG_1 CN Type: 6-pin header, p=1.25 mm CN Location: See Figure 3-6 CN Pinouts: See Table 3-7 The DEBUG_1 connector is used for EC debug (with SPI protocol). Figure 3-6: EC Debug Connector Location PIN NO.

  • Page 36: Chassis Intrusion Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.6 Chassis Intrusion Connector CN Label: CHASSIS1 CN Type: 2-pin header, p=2.54 mm CN Location: See Figure 3-7 CN Pinouts: See Table 3-8 The CHASSIS1 (Chassis Intrusion Connector) Figure 3-7: Chassis Intrusion Connector Location PIN NO.

  • Page 37: Raa229134 Fw Flash And Lt86101X Fw Flash Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.7 RAA229134 FW Flash And LT86101X FW Flash Connector CN Label: J1, J2 CN Type: 3-pin header, p=2.00 mm CN Location: See Figure 3-8 CN Pinouts: See Table 3-9 The J1(RAA229134 FW Flash Connector) and J2(LT86101X FW Flash Connector).

  • Page 38: Cpu Fan Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.8 CPU Fan Connector CN Label: CPU_FAN1 CN Type: 4-pin wafer, p=2.54 mm CN Location: See Figure 3-9 CN Pinouts: See Table 3-10 The fan connector attaches to a CPU cooling fan. Figure 3-9: CPU Fan Connector Location PIN NO.

  • Page 39: System Fan Connectors

    IMB-ADL-H610 Micro ATX Motherboard 3.2.9 System Fan Connectors CN Label: SYS_FAN1, SYS_FAN2 CN Type: 4-pin wafer, p=2.54 mm CN Location: See Figure 3-10 CN Pinouts: See Table 3-11 and Table 3-12 Each fan connector attaches to a system cooling fan.

  • Page 40: Table 3-11: System Fan (Sys_Fan1) Connector Pinouts

    IMB-ADL-H610 Micro ATX Motherboard PIN NO. DESCRIPTION +12V FANIO PWM (+5V) Table 3-11: System Fan (SYS_FAN1) Connector Pinouts PIN NO. DESCRIPTION +12V FANIO PWM (+5V) Table 3-12: System Fan (SYS_FAN2) Connector Pinouts Page 40...

  • Page 41: Audio Connector For Iei Ac-Kit-888S Kit

    IMB-ADL-H610 Micro ATX Motherboard 3.2.10 Audio Connector for IEI AC-KIT-888S kit CN Label: IAUDIO CN Type: 10-pin header, p=2.00 mm CN Location: See Figure 3-11 CN Pinouts: See Table 3-13 This connector connects to IEI AC-KIT-888S audio kit. Figure 3-11: IAUDIO Location PIN NO.

  • Page 42: Front Panel Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.11 Front Panel Connector CN Label: F_PANEL1 CN Type: 14-pin header, p=2.54 mm CN Location: See Figure 3-12 CN Pinouts: See Table 3-14 The front panel connector connects to the indicator LEDs, speaker and buttons on the computer's front panel.

  • Page 43: I 2 C Connector

    IMB-ADL-H610 Micro ATX Motherboard DESCRIPTION DESCRIPTION PWR_LED+ SPKR+ PWR LED SPKR PWR_LED- PWR_BTN+ SPKR- PWR BTN PWR_BTN- HDD_LED+ RESET+ HDD LED RESET HDD_LED- RESET- Table 3-14: Front Panel Connector Pinouts 3.2.12 I C Connector CN Label: J_I2C1 CN Type: 4-pin wafer, p=1.25 mm...

  • Page 44: Smbus Connector

    IMB-ADL-H610 Micro ATX Motherboard PIN NO. DESCRIPTION I2C_CLK Table 3-15: I2C Connector Pinouts 3.2.13 SMBus Connector CN Label: J_SMB1 CN Type: 4-pin wafer, p=1.25 mm CN Location: See Figure 3-14 CN Pinouts: See Table 3-16 The SMBus (System Management Bus) connector provides low-speed system management communications.

  • Page 45: Lan Link Led Connector

    IMB-ADL-H610 Micro ATX Motherboard Description SMB_DATA SMB_CLK Table 3-16: SMBus Connector Pinouts 3.2.14 LAN link LED Connector CN Label: JLAN_LED1, JLAN_LED2 CN Type: 2-pin header, p=2.54 mm CN Location: See Figure 3-15 CN Pinouts: See Table 3-17 and Table 3-18 The LAN LED connectors are used to connect to the LAN LED indicators on the chassis to indicate users the link activities of the two LAN ports.

  • Page 46: M-Key (2280) Slot

    IMB-ADL-H610 Micro ATX Motherboard Description +3.3V LAN1_LED_LINK#_ACT Table 3-17: LAN1 LED Connector (LED_LAN1) Pinouts Description +3.3V LAN2_LED_LINK#_ACT Table 3-18: LAN2 LED Connector (LED_LAN2) Pinouts 3.2.15 M.2 M-key (2280) slot CN Label: M2_M1 CN Type: M-key slot CN Location: See Figure 3-16...

  • Page 47: Figure 3-16: M.2 M-Key Slot Locations

    IMB-ADL-H610 Micro ATX Motherboard Figure 3-16: M.2 M-key slot Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION +3.3V +3.3V PERN3 PERP3 DAS/DSS# PETN3 +3.3V PETP3 +3.3V +3.3V PERN2 +3.3V PERP2 PETN2 PETP2 Page 47...

  • Page 48: Table 3-19: M.2 M-Key Slot Pinouts

    IMB-ADL-H610 Micro ATX Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION PERN1 PERP1 PETN1 PETP1 DEVSLP PERN0/SATA-B+ PERP0/SATA-B- PETN0/SATA-A- PETP0/SATA-A+ PERST#NC CLKREQ#NC REFCLKN PEWAKE/NC REFCLKP Notch0 Notch1 Notch2 Notch3 Notch4 Notch5 Notch6 Notch7 SUSCLK PEDET +3.3V +3.3V +3.3V Table 3-19: M.2 M-Key slot Pinouts...

  • Page 49: Pcie X1 Slots

    IMB-ADL-H610 Micro ATX Motherboard 3.2.16 PCIe x1 Slots CN Label: PCIE2, PCIE4 CN Type: PCIe x1 slots CN Location: See Figure 3-17 The PCIe slot enables a PCIe expansion module to be connected to the board. Figure 3-17: PCIe x1 Slot Locations...

  • Page 50: Pcie X4 Slot

    IMB-ADL-H610 Micro ATX Motherboard 3.2.17 PCIe x4 Slot CN Label: PCIE3 CN Type: PCIe x4 slot CN Location: See Figure 3-18 The PCIe x4 expansion card slot are for PCIe x4 expansion cards. Figure 3-18: PCIe x4 Slot Location Page 50...

  • Page 51: Pcie X16 Slot

    IMB-ADL-H610 Micro ATX Motherboard 3.2.18 PCIe x16 Slot CN Label: PCIE1 CN Type: PCIe x16 slot CN Location: See Figure 3-19 The PCIe x16 expansion card slot are for PCIe x16 expansion cards. Figure 3-19: PCIe x16 Slot Location Page 51...

  • Page 52: Ddr4 Dimm Sockets

    IMB-ADL-H610 Micro ATX Motherboard 3.2.19 DDR4 DIMM Sockets CN Label: CHA_DIMM1, CHB_DIMM1 CN Type: 288-pin socket CN Location: See Figure 3-20 The DIMM slots are for DDR4 DIMM memory modules Figure 3-20: DDR4 DIMM Sockets Location Page 52...

  • Page 53: Sata 6Gb/S Connectors

    IMB-ADL-H610 Micro ATX Motherboard 3.2.20 SATA 6Gb/s Connectors CN Label: SATA1, SATA2, SATA3, SATA4 CN Type: 7-pin SATA connector，p=1.27mm CN Location: See Figure 3-21 CN Pinouts: See Table 3-20 The SATA drive connectors can be connected to SATA drives and support up to 6Gb/s data transfer rate.

  • Page 54: Serial Port Connectors

    IMB-ADL-H610 Micro ATX Motherboard PIN NO. DESCRIPTION SATA RX+ Table 3-20: SATA 6Gb/s Connector Pinouts 3.2.21 RS-232 Serial Port Connectors CN Label: COM3, COM4, COM5, COM6 CN Type: 10-pin box header, p=2.54 mm CN Location: See Figure 3-22 CN Pinouts: See Table 3-21 Each of these connectors provides RS-232 connections.

  • Page 55: Flash Spi Rom Connector

    IMB-ADL-H610 Micro ATX Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION Table 3-21: RS-232 Serial Port Connector Pinouts 3.2.22 Flash SPI ROM Connector CN Label: JSPI1 CN Type: 6 pin header, p=1.25 mm CN Location: See Figure 3-23 CN Pinouts: See Table 3-22 The Flash SPI ROM connector is used to flash the SPI ROM.

  • Page 56: Flash Ec Rom Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.23 Flash EC ROM Connector CN Label: JEC1 CN Type: 8-pin header, p=1.27 mm CN Location: See Figure 3-24 CN Pinouts: See Table 3-23 The Flash EC ROM connector is used to flash the EC ROM.

  • Page 57: Internal Usb 2.0 Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.2.24 Internal USB 2.0 Connector CN Label: USB2_CN1 CN Type: 8pin header, p=2.54 mm CN Location: See Figure 3-25 CN Pinouts: See Table 3-24 The Internal USB 2.0 connector connects to USB 2.0 devices. Figure 3-25: Internal USB 2.0 Connector Locations PIN NO.

  • Page 58: External Peripheral Interface Connector Panel

    CN Label: USB2_1 CN Type: USB 2.0 CN Location: See Figure 3-27 CN Pinouts: See Table 3-25 There are four external USB 2.0 connectors on the IMB-ADL-H610. The USB 2.0 connector can be connected to a USB 2.0/1.1 device Page 58...

  • Page 59: External Hdmi And Dp Combo Connector

    IMB-ADL-H610 Micro ATX Motherboard Figure 3-27: USB 2.0 Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION USB_VCC USB_VCC USB_VCC USB_VCC Table 3-25: USB 2.0 Port Pinouts 3.3.2 External HDMI And DP Combo Connector CN Label: HDMI_DP1 CN Type: HDMI, DisplayPort CN Location:...

  • Page 60: Figure 3-28: Hdmi Connector

    IMB-ADL-H610 Micro ATX Motherboard Description Description HDMI_CLK HDMI_DATA1N HDMI_SDA HDMI_DATA0P HDMI_DATA0N HDMI_HPD HDMI_CLKP Table 3-26: HDMI Connector Pinouts Figure 3-28: HDMI Connector The DP connector connects to a display device with DisplayPort interface. Description Description LANE0P LANE3N LANE0N CONFIG_A_1 LANE1P...

  • Page 61: External Rs-232/422/485 Combo Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.3.3 External RS-232/422/485 Combo Connector CN Label: COM1, COM2 CN Type: Dual DB-9 CN Location: See Figure 3-30 CN Pinouts: See Table 3-28 The COM connector (COM1) and the COM connector (COM2) connects to a serial device that supports RS-232/422/485 communication.

  • Page 62: External 1Gbe Rj-45 And External Dual Usb 3.2 Gen1 Connector

    IMB-ADL-H610 Micro ATX Motherboard 3.3.4 External 1GbE RJ-45 And External Dual USB 3.2 Gen1 Connector CN Label: LAN1_USB1 CN Type: 12-PIN 1GbE and 18-PIN USB 3.2 CN Location: See Figure 3-31 CN Pinouts: See Table 3-29 and Table 3-30 The LAN1_USB1 connector supports dual USB 3.2 Gen 1 (5Gb/s) and 1GbE LAN RJ-45.

  • Page 63: External 2.5Gbe Rj-45 And Dual Usb 3.2 Gen 2 Connector

    IMB-ADL-H610 Micro ATX Motherboard Figure 3-31: USB3.2 And RJ45 LAN Connector 3.3.5 External 2.5GbE RJ-45 And Dual USB 3.2 Gen 2 Connector CN Label: LAN2_USB2 CN Type: 2.5GbE RJ-45 and USB 3.2 Gen 2 Type A CN Location: See Figure 3-32...

  • Page 64: Table 3-31:External Lan 2.5Gbe Connector Pinouts

    IMB-ADL-H610 Micro ATX Motherboard Table 3-31:External LAN 2.5GbE Connector Pinouts PIN NO. DESCRIPTION PIN NO. DESCRIPTION USB_DATA- USB_DATA- USB_DATA+ USB_ DATA+ USB3_RX- USB3_RX- USB3_RX+ USB3_ RX+ USB3_TX- USB3_TX- USB3_TX+ USB3_TX+ Table 3-32: External Dual USB 3.2 Gen 2 Connector Pinouts...

  • Page 65: Installation

    IMB-ADL-H610 Micro ATX Motherboard Chapter Installation Page 65...

  • Page 66: Anti-Static Precautions

    Electrostatic discharge (ESD) can cause serious damage to electronic components, including the IMB-ADL-H610. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the IMB-ADL-H610 or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
  • Page 67 This helps to prevent potential ESD damage. Turn all power to the IMB-ADL-H610 off: ▪ When working with the IMB-ADL-H610, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system.

  • Page 68: Socket Lga1700 Cpu Installation

    IMB-ADL-H610 Micro ATX Motherboard 4.3 Socket LGA1700 CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed.

  • Page 69: Figure 4-2: Remove Protective Cover

    IMB-ADL-H610 Micro ATX Motherboard Figure 4-2: Remove Protective Cover Step 3: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air.

  • Page 70: Figure 4-3: Insert The Socket Lga1700 Cpu

    IMB-ADL-H610 Micro ATX Motherboard Step 7: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU should slide into the CPU socket smoothly. See Figure 4-3. Figure 4-3: Insert the Socket LGA1700 CPU Step 8: Close the CPU socket.

  • Page 71: Socket Lga1700 Cooling Kit Installation

    IMB-ADL-H610 Micro ATX Motherboard Step 9: Connect the 12 V power to the board. Connect the 12 V power from the power supply to the board. Step 0: 4.4 Socket LGA1700 Cooling Kit Installation WARNING: DO NOT attempt to install a push-pin cooling fan.

  • Page 72: Figure 4-5: Cooling Kit Support Bracket

    IMB-ADL-H610 Micro ATX Motherboard Figure 4-5: Cooling Kit Support Bracket Step 2: Place the cooling kit onto the socket LGA1700 CPU. Make sure the CPU cable can be properly routed when the cooling kit is installed. Step 3: Mount the cooling kit. Gently place the cooling kit on top of the CPU. Make sure the four threaded screws on the corners of the cooling kit properly pass through the holes of the cooling kit bracket.

  • Page 73: Dimm Installation

    IMB-ADL-H610 Micro ATX Motherboard 4.5 DIMM Installation To install a DIMM, please follow the steps below and refer to Figure 4-6. Figure 4-6: DIMM Installation Step 1: Open the DIMM socket handles. Open the two handles outwards as far as they can.

  • Page 74: System Configuration

    IMB-ADL-H610 Micro ATX Motherboard 4.6 System Configuration The system configuration is controlled by jumpers, buttons, switches and BIOS options. The system configuration must be performed before installation. 4.6.1 AT/ATX Power Mode Setting The AT and ATX power mode selection is made through the AT/ATX power mode switch which is shown in Figure 4-7.

  • Page 75: Clearing Cmos

    IMB-ADL-H610 Micro ATX Motherboard 4.6.2 Clearing CMOS To reset the BIOS, remove the on-board battery and short the J_CMOS1 connector the clear CMOS connector is shown in Figure 4-8 Figure 4-8: Clear CMOS Jumper Location Status DESCRIPTION Keep CMOS Setup...

  • Page 76: Figure 4-9: Flash Descriptor Security Override Jumper Location

    IMB-ADL-H610 Micro ATX Motherboard PIN NO. DESCRIPTION Short Enabled Table 4-3: Flash Descriptor Security Override Jumper Pinouts Figure 4-9: Flash Descriptor Security Override Jumper Location To update the ME firmware, please follow the steps below. Step 1: Before turning on the system power, short pin 2-3 of the flash descriptor security override jumper.

  • Page 77: Internal Peripheral Device Connections

    This section outlines the installation of peripheral devices to the onboard connectors. 4.7.1 SATA Drive Connection The IMB-ADL-H610 is shipped with two SATA drive cables. To connect the SATA drives to the connectors, please follow the steps below. Step 1: Locate the connectors.

  • Page 78: Figure 4-11: Sata Power Drive Connection

    IMB-ADL-H610 Micro ATX Motherboard Figure 4-11: SATA Power Drive Connection The SATA power cable can be bought from IEI. See Optional Items in Section 2.4. Page 78...

  • Page 79: Software Installation

    IMB-ADL-H610 Micro ATX Motherboard 4.8 Software Installation All the drivers for the IMB-ADL-H610 are available on IEI Resource Download Center (https://download.ieiworld.com). Type IMB-ADL-H610 and press Enter to find all the relevant software, utilities, and documentation. Figure 4-12: IEI Resource Download Center 4.9 Driver Download...
  • Page 80 IMB-ADL-H610 Micro ATX Motherboard Step 3: Click the driver file name on the page and you will be prompted with the  following window. You can download the entire ISO file ( ), or click the small  arrow to find an individual driver and click the file name to download (...

  • Page 81: Bios

    IMB-ADL-H610 Micro ATX Motherboard Chapter BIOS Page 81...

  • Page 82: Introduction

    IMB-ADL-H610 Micro ATX Motherboard 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

  • Page 83: Using Setup

    IMB-ADL-H610 Micro ATX Motherboard 5.1.2 Using Setup The BIOS Setup menu can be navigated by using a keyboard or a touchscreen. 5.1.2.1 Keyboard Navigation For keyboard navigation, use the navigation keys shown in Table 5-1. Function Up arrow Move to previous item...

  • Page 84: Touch Navigation

    IMB-ADL-H610 Micro ATX Motherboard 5.1.2.2 Touch Navigation For touchscreen navigation, use the on-screen navigation keys shown below. On-screen Button Function Previous Values Load the last value you set. Optimized Defaults Load the factory default values in order to achieve the best performance.

  • Page 85: Getting Help

    IMB-ADL-H610 Micro ATX Motherboard 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window, press the key. 5.1.4 Unable to Reboot after Configuration Changes If the computer cannot boot after changes to the system configuration is made, CMOS defaults.

  • Page 86: Main

    IMB-ADL-H610 Micro ATX Motherboard 5.2 Main The Main BIOS menu appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS Menu 1: Main (1/3) Page 86...
  • Page 87 IMB-ADL-H610 Micro ATX Motherboard BIOS Menu 2: Main (2/3) BIOS Menu 3: Main (3/3) Page 87...
  • Page 88 IMB-ADL-H610 Micro ATX Motherboard ➔ BIOS Information The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information cannot be changed. The items shown in the system overview include: ▪ BIOS Vendor: Installed BIOS vendor ▪...
  • Page 89 IMB-ADL-H610 Micro ATX Motherboard ➔ System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. ➔ System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.

  • Page 90: Advanced

    IMB-ADL-H610 Micro ATX Motherboard 5.3 Advanced Use the Advanced menu (BIOS Menu 4) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.

  • Page 91: Case Open Detection

    IMB-ADL-H610 Micro ATX Motherboard 5.3.1 Case Open Detection ➔ Case Open Detection [Disabled] When the Case Open Detection is enabled, if anyone opens the computer's chassis, or case, Windows will notify the user with a pop-up message the next time he turns on his computer.
  • Page 92 IMB-ADL-H610 Micro ATX Motherboard BIOS Menu 6: CPU Configuration (2/3) BIOS Menu 7: CPU Configuration (3/3) Page 92...
  • Page 93 IMB-ADL-H610 Micro ATX Motherboard ➔ Intel (VMX) Virtualization Technology [Enabled] Use the Intel (VMX) Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel® Virtualization technology allows several OSs to run on the same system at the same time.
  • Page 94 IMB-ADL-H610 Micro ATX Motherboard ➔ Enable four E-cores in the processor package. ➔ Enable five E-cores in the processor package. ➔ Enable six E-cores in the processor package. ➔ Enable seven E-cores in the processor package. ➔ Hyper-Threading [Enabled] Use the Hyper-Threading option to enable or disable the Hyper-Threading Technology.
  • Page 95 IMB-ADL-H610 Micro ATX Motherboard ➔ Power Limit 1 Time Window [0] Use the Power Limit 1 Time Window option to select the PL1 time duration. The value may vary from 0 to 128. For 0 is the default value ➔...

  • Page 96: Trusted Computing

    IMB-ADL-H610 Micro ATX Motherboard 5.3.3 Trusted Computing Use the Trusted Computing menu (BIOS Menu 8) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM). BIOS Menu 8: Trusted Computing Configuration ➔ TPM Support [Enable] Use the TPM Support option to enable or disable BIOS support for security device.

  • Page 97: Rtc Wake Settings

    IMB-ADL-H610 Micro ATX Motherboard 5.3.4 RTC Wake Settings The RTC Wake Settings menu (BIOS Menu 9) configures RTC wake event. BIOS Menu 9: RTC Wake Settings (1/2) BIOS Menu 10: RTC Wake Settings (2/2) Page 97...
  • Page 98 IMB-ADL-H610 Micro ATX Motherboard ➔ Wake system with Fixed Time [Enabled] Use the Wake system with Fixed Time option to enable or disable the system wake on alarm event. ➔ Disabled The real time clock (RTC) cannot generate a wake event ➔...

  • Page 99: F81966 Super Io Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.5 F81966 Super IO Configuration Use the F81966 Super IO Configuration menu (BIOS Menu 11) to set or change the configurations for serial ports. BIOS Menu 11: F81866 Super IO Configuration Page 99...

  • Page 100: Serial Port 1 Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.5.1 Serial Port 1 Configuration Use the Serial Port 1 Configuration menu (BIOS Menu 12) to configure the serial port. BIOS Menu 12: Serial Port 1 Configuration Menu ➔ Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.
  • Page 101 IMB-ADL-H610 Micro ATX Motherboard ➔ RS232 The serial port mode is RS-232 EFAULT RS422 with The serial port mode is RS-422 termination resistor RS485 with The serial port mode is RS-485 termination resistor Page 101...

  • Page 102: Serial Port 2 Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.5.2 Serial Port 2 Configuration Use the Serial Port 2 Configuration menu (BIOS Menu 13) to configure the serial port. BIOS Menu 13: Serial Port 2 Configuration Menu ➔ Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.
  • Page 103 IMB-ADL-H610 Micro ATX Motherboard ➔ RS232 The serial port mode is RS-232 EFAULT RS422 with The serial port mode is RS-422 termination resistor RS485 with The serial port mode is RS-485 termination resistor Page 103...

  • Page 104: Serial Port 3 Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.5.3 Serial Port 3 Configuration Use the Serial Port 3 Configuration menu (BIOS Menu 14) to configure the serial port. BIOS Menu 14: Serial Port 3 Configuration Menu ➔ Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.

  • Page 105: Serial Port 4 Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.5.4 Serial Port 4 Configuration Use the Serial Port 4 Configuration menu (BIOS Menu 15) to configure the serial port. BIOS Menu 15: Serial Port 4 Configuration Menu ➔ Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.

  • Page 106: Serial Port 5 Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.5.5 Serial Port 5 Configuration Use the Serial Port 5 Configuration menu (BIOS Menu 16) to configure the serial port. BIOS Menu 16: Serial Port 5 Configuration Menu ➔ Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.

  • Page 107: Serial Port 6 Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.5.6 Serial Port 6 Configuration Use the Serial Port 6 Configuration menu (BIOS Menu 17) to configure the serial port. BIOS Menu 17: Serial Port 6 Configuration Menu ➔ Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.

  • Page 108: Ec Kb9068 H/W Monitor

    IMB-ADL-H610 Micro ATX Motherboard 5.3.6 EC KB9068 H/W Monitor The EC KB9068 H/W Monitor menu (BIOS Menu 18) contains the smart fan mode configuration submenu and shows the state of H/W real-time operating temperature, fan speeds and system voltages. BIOS Menu 18: EC KB9068 H/W Monitor (1/2)
  • Page 109 IMB-ADL-H610 Micro ATX Motherboard BIOS Menu 19: EC KB9068 H/W Monitor (2/2) ➔ PC Health Status The following system parameters and values are shown. The system parameters that are monitored are: ▪ System Temperatures: CPU Temperature System Temperature1 System Temperature2 ▪...
  • Page 110 IMB-ADL-H610 Micro ATX Motherboard ▪ Voltages: +VCCCORE +5VS +12S +3VP3S VCCGT +VDDQ VCCIN_AUX_CPU ➔ Tcc Activation Offset [0] Offset from factoryset Tcc activation temprature at which the Thermal Control Circuit must be activated. Tcc will be activated at: Tcc Activation Temp-Tcc Activation Offset.Tcc Activation Offset range is 0 to 63.

  • Page 111: Smart Fan Mode Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.6.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 20) to configure the CPU/system fan start/off temperature and control mode. BIOS Menu 20: Smart Fan Mode Configuration (1/2) Page 111...
  • Page 112 IMB-ADL-H610 Micro ATX Motherboard BIOS Menu 21: Smart Fan Mode Configuration (2/2) ➔ CPU_FAN1 Smart Fan Control [Auto Mode] Use the CPU_FAN1 Smart Fan Control option to configure the CPU Smart Fan. ➔ Manual Mode The fan spins at the speed set in Manual Mode settings.
  • Page 113 IMB-ADL-H610 Micro ATX Motherboard ➔ CPU_FAN1 Start Temperature If the CPU temperature is between fan off and fan start, the fan speed change to fan start PWM. To set a value, Use the + or – key to change the value or enter a decimal number between 1 and 100.
  • Page 114 IMB-ADL-H610 Micro ATX Motherboard ➔ SYS_FAN1 Start PWM Use the SYS_Fan1 Start PWM option to set the PWM start value. Use the + or – key to change the value or enter a decimal number between 1 and 100. ➔...
  • Page 115 IMB-ADL-H610 Micro ATX Motherboard ➔ Auto mode fan slope PWM The PWM slope refers to the ratio relationship between the fan speed and the temperature. When the temperature rises or falls by 1° C, the fan speed increases or decreases accordingly.

  • Page 116: Serial Port Console Redirection

    IMB-ADL-H610 Micro ATX Motherboard 5.3.7 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 22) allows the console redirection options to be configured. Console Redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port.
  • Page 117 IMB-ADL-H610 Micro ATX Motherboard BIOS Menu 23: Serial Port Console Redirection (2/2) ➔ Console Redirection [Disabled] Use Console Redirection option to enable or disable the console redirection function. ➔ Disabled Disabled the console redirection function EFAULT ➔ Enabled Enabled the console redirection function The Console Redirection Settings submenu will be available when the Console Redirection option is enabled.

  • Page 118: Console Redirection Settings

    IMB-ADL-H610 Micro ATX Motherboard 5.3.7.1 Console Redirection Settings The following options are available in the Console Redirection Settings submenu (BIOS Menu 24) when the COM Console Redirection (for COM1 to COM6) option is enabled. BIOS Menu 24: COM Console Redirection Settings Terminal Type [ANSI] ➔...
  • Page 119 IMB-ADL-H610 Micro ATX Motherboard ➔ 9600 Sets the serial port transmission speed at 9600. ➔ 19200 Sets the serial port transmission speed at 19200. ➔ 38400 Sets the serial port transmission speed at 38400. ➔ 57600 Sets the serial port transmission speed at 57600.
  • Page 120 IMB-ADL-H610 Micro ATX Motherboard ➔ Sets the number of stop bits at 2. Page 120...

  • Page 121: Nvme Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.3.8 NVMe Configuration Use the NVMe Configuration (BIOS Menu 25) menu to display the NVMe controller and device information. BIOS Menu 25: NVMe Configuration Page 121...

  • Page 122: Chipset

    IMB-ADL-H610 Micro ATX Motherboard 5.4 Chipset Use the Chipset menu (BIOS Menu 26) to access the PCH IO and System Agent (SA) configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.

  • Page 123: System Agent (Sa) Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.4.1 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 27) to configure the System Agent (SA) parameters. BIOS Menu 27: System Agent (SA) Configuration ➔ VT-d [Enabled] Use the VT-d option to enable or disable the VT-d capability.

  • Page 124: Memory Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.4.1.1 Memory Configuration Use the Memory Configuration submenu (BIOS Menu 28) to view memory information. BIOS Menu 28: Memory Configuration Page 124...

  • Page 125: Graphics Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.4.1.2 Graphics Configuration Use the Graphics Configuration (BIOS Menu 29) menu to configure the video device connected to the system. BIOS Menu 29: Graphics Configuration ➔ Primary Display [Auto] Use the Primary Display option to select the primary graphics controller the system uses.
  • Page 126 IMB-ADL-H610 Micro ATX Motherboard option should be set to Enabled and the above Primary Display option should be set to IGFX. ➔ Auto Auto mode ➔ Disabled Disables IGFX. ➔ Enabled Default Enables IGFX. ➔ DVMT Pre-Allocated [160M] Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the integrated graphics processor when the system boots.

  • Page 127: Peg Port Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.4.1.3 PEG Port Configuration BIOS Menu 30: PEG Port Configuration ➔ Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to detect non-compliance PCIe device in PEG. ➔ Disabled Do not detect non-compliance PCIe device in PEG EFAULT ➔...

  • Page 128: Pcie1

    IMB-ADL-H610 Micro ATX Motherboard PCIE1 BIOS Menu 31: PCIE1 ➔ PCIE1 [Enabled] Use PCIE1 to control the PCI Express root port. ➔ Enabled EFAULT ➔ Disabled PCIe Speed [Auto] ➔ Use the PCIe Speed option to specify the PCI Express port speed. Configuration options are listed below.
  • Page 129 IMB-ADL-H610 Micro ATX Motherboard ➔ Gen4 Configure PCIe Speed to Gen4. ➔ Gen5 Configure PCIe Speed to Gen5. Page 129...

  • Page 130: Pch-Io Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.4.2 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 32) to configure the PCH parameters. BIOS Menu 32: PCH-IO Configuration (1/2) Page 130...
  • Page 131 IMB-ADL-H610 Micro ATX Motherboard BIOS Menu 33: PCH-IO Configuration (2/2) ➔ Auto Power Button Function [Disabled (AT)] Use the Auto Power Button Function BIOS option to show the power mode state. Use the J_ATX_AT1 to switch the AT/ATX power mode.
  • Page 132 IMB-ADL-H610 Micro ATX Motherboard ➔ USB Power SW1(LAN2_USB2) [S0/S3/S4/S5 ON] Use the USB Power SW1 to enable or disable the USB Power. ➔ S0/S3/S4/S5 ON EFAULT ➔ S0/S3/S4/S5 OFF ➔ USB Power SW2(LAN1_USB1) [S0/S3/S4/S5 ON] Use the USB Power SW2 to enable or disable the USB Power.
  • Page 133 IMB-ADL-H610 Micro ATX Motherboard ➔ USB Power SW7(USB2_CN1_C6) [S0/S3/S4/S5 ON] Use the USB Power SW7 to enable or disable the USB Power. ➔ S0/S3/S4/S5 ON EFAULT ➔ S0/S3/S4/S5 OFF Page 133...

  • Page 134: Pci Express Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.4.2.1 PCI Express Configuration Use the PCI Express Configuration submenu (BIOS Menu 34) to configure the PCI Express slots. BIOS Menu 34: PCI Express Configuration Page 134...

  • Page 135: Pcie3, Pcie2, Pcie4, M2_M1

    IMB-ADL-H610 Micro ATX Motherboard 5.4.2.2 PCIE3, PCIE2, PCIE4, M2_M1 Use the PCIE3，PCIE2，PCIE4，M2_M1 submenu (BIOS Menu 35) to configure the PCI Root Port Setting. BIOS Menu 35: PCIe Slot Configuration Submenu ➔ PCIe Speed [Auto] Use the PCIe Speed option to specify the PCI Express port speed. Configuration options are listed below.
  • Page 136 IMB-ADL-H610 Micro ATX Motherboard ➔ Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to configure whether to detect if a non- compliance PCI Express device is connected to the PCI Express port. ➔ Disabled Do not detect if a non-compliance PCI Express EFAULT device is connected to the PCI Express port.

  • Page 137: Sata Configuration

    IMB-ADL-H610 Micro ATX Motherboard 5.4.2.3 SATA Configuration Use the SATA Configuration menu (BIOS Menu 36) to change and/or set the configuration of the SATA devices installed in the system. BIOS Menu 36: SATA Configuration ➔ SATA Mode Selection [AHCI] Use the SATA Mode Selection option to determine how the SATA devices operate.

  • Page 138: Hd Audio Configuration

    IMB-ADL-H610 Micro ATX Motherboard ➔ Enabled Designates the SATA port as hot-pluggable. 5.4.2.4 HD Audio Configuration Use the HD Audio Configuration menu (BIOS Menu 37) to configure the PCH Azalia settings. BIOS Menu 37: HD Audio Configuration ➔ HD Audio [Enabled] Use the HD Audio option to enable or disable the High Definition Audio controller.

  • Page 139: Security

    IMB-ADL-H610 Micro ATX Motherboard 5.5 Security Use the Security menu (BIOS Menu 39) to set system and user passwords. BIOS Menu 38: Security (1/2) Page 139...
  • Page 140 IMB-ADL-H610 Micro ATX Motherboard BIOS Menu 39: Security (2/2) ➔ Administrator Password Use the Administrator Password to set or change an administrator password. ➔ User Password Use the User Password to set or change a user password. Page 140...

  • Page 141: Boot

    IMB-ADL-H610 Micro ATX Motherboard 5.6 Boot Use the Boot menu (BIOS Menu 40) to configure system boot options. BIOS Menu 40: Boot 5.6.1 Boot Configuration ➔ Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.

  • Page 142: Save & Exit

    IMB-ADL-H610 Micro ATX Motherboard ➔ Disabled Ignore all PXE Option ROMs EFAULT ➔ Enabled Load PXE Option ROMs. 5.7 Save & Exit Use the Save & Exit menu (BIOS Menu 41) to load default BIOS values, optimal failsafe values and to save configuration changes.
  • Page 143 IMB-ADL-H610 Micro ATX Motherboard ➔ Restore Defaults Use the Restore Defaults option to load the optimal default values for each of the parameters on the Setup menus. F3 key can be used for this operation. ➔ Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults.

  • Page 144: A Regulatory Compliance

    IMB-ADL-H610 Micro ATX Motherboard Appendix Regulatory Compliance Page 144...
  • Page 145 IMB-ADL-H610 Micro ATX Motherboard DECLARATION OF CONFORMITY This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or installs other devices in the equipment, the CE conformity declaration may no longer apply.

  • Page 146: B Product Disposal

    IMB-ADL-H610 Micro ATX Motherboard Appendix Product Disposal Page 146...
  • Page 147 IMB-ADL-H610 Micro ATX Motherboard CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. ▪ Outside the European Union–If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.

  • Page 148: C Error Beep Code

    IMB-ADL-H610 Micro ATX Motherboard Appendix Error Beep Code Page 148...

  • Page 149: Pei Beep Codes

    IMB-ADL-H610 Micro ATX Motherboard C.1 PEI Beep Codes Number of Beeps Description Memory not Installed Memory was installed twice (InstallPeiMemory routine in PEI Core called twice) Recovery started DXEIPL was not found DXE Core Firmware Volume was not found Recovery failed...

  • Page 150: D Watchdog Timer

    IMB-ADL-H610 Micro ATX Motherboard Appendix Watchdog Timer Page 150...
  • Page 151 IMB-ADL-H610 Micro ATX Motherboard NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...

  • Page 152: E Hazardous Materials Disclosure

    IMB-ADL-H610 Micro ATX Motherboard Appendix Hazardous Materials Disclosure Page 152...

  • Page 153: Rohs Ii Directive (2015/863/Eu)

    IMB-ADL-H610 Micro ATX Motherboard E.1 RoHS II Directive (2015/863/EU) The details provided in this appendix are to ensure that the product is compliant with the RoHS II Directive (2015/863/EU). The table below acknowledges the presences of small quantities of certain substances in the product, and is applicable to RoHS II Directive (2015/863/EU).

  • Page 154: China Rohs

    IMB-ADL-H610 Micro ATX Motherboard E.2 China RoHS 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 壳体 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11364-2014 與 GB/T26572- 2011 标准规定的限量要求以下。 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11364-2014 與 GB/T26572-2011 标准规定的限量要求。 Page 154...

Table of Contents