Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Flex innovations EDGE 540FP
Summary of Contents for Flex innovations EDGE 540FP
- Page 1 Assembly Manual...
- Page 2 Edge 540 FP Instructions Introduction Flex Innovations is thrilled to introduce the Foam Profile (FP) line of aircraft. For years, profile foam aircraft have attracted modelers of all types due to their combination of enjoyment and durability. Now, Flex has committed to revolutionizing this type of aircraft by combining high level performance and equipment with a simple PNP style assembly process.
-
Page 3: Replacement Parts
Edge 540 FP Instructions Replacement Parts FPM527001 Flex Edge 540 FP Plastic Parts Sheet FPM527002A Flex Edge 540 FP Green Foam Wheel Pant and Landing Gear Sheet FPM527002B Flex Edge 540 FP Red Foam Wheel Pant and Landing Gear Sheet FPZA1057 ... - Page 4 Edge 540 FP Instructions ATTENTION Read the ENTIRE instruction manual to become familiar with the features and assembly of the product before starting assembly. Failure to assemble or operate the product correctly can result in damage to the product, personal property and cause serious or fatal injury.
-
Page 5: Safety Warnings And Precautions
4. This model must be assembled according to these instructions. Do not alter or modify the model outside of these instructions provided by Flex Innovations, LLC, as doing so may render it unsafe and/or unflyable. You must take time to build straight, true, and strong. It is your responsibility to ensure the air worthiness of this product. - Page 6 Edge 540 FP Instructions Tools/Supplies needed Including but not limited to: -Contact Foam Adhesive (FPMJQ2118) or Foam-Cure (BSI142) -Medium CA (Foam safe not required) -Hobby knife with fresh blades -Phillips screwdriver -CA Accelerator (BSI151) -Parchment/Baking paper for a building surface (highly recommended)
-
Page 7: Main Wing Installation
Edge 540 FP Instructions Main Wing Installation 1) Locate the main wing and main fuselage sections. Test fit the main wing into the cutout in the fuselage. Once all is straight and well fitting, apply building adhesive to glue in place. *It is recommended to use parchment paper as a building surface. -
Page 8: Landing Gear Installation
Edge 540 FP Instructions Landing Gear Installation 1) Locate the main landing gear along with the plastic landing gear supports. 2) Slide the landing gear through the plastic landing gear supports as shown: 3) Locate the two dots marked on the fuselage for location of the landing gear. - Page 9 Edge 540 FP Instructions Top Fuselage / Motor Bolt 1) Locate the top piece of the fuselage 2) Test fit the top fuselage tabs with the horizontal fuselage slots. 3) Once all is confirmed, glue into place. 4) Be sure to apply glue on both the front edge of the fuse (attached to motor mount) as well as the rear bottom (attached to flat carbon tailpiece) 5) Be sure that the top fuselage piece is 90 degrees to the horizontal fuselage.
- Page 10 Edge 540 FP Instructions Top Carbon Fiber Trussing 1) Install small carbon fiber rods on each side of the front portion of the fuselage to prevent twisting. 2) Install carbon fiber rods attaching from the vertical stab to horizontal stab. Make sure fuselage is set straight 90 degrees after applying.
-
Page 11: Radio Setup
Use a Phillips screwdriver to tighten the connectors once centered. 3) Low Rate/Precision: 50% Dual Rates at 60-70% expo High/3D/XA Rate: 100% Dual Rates at 50% expo Center of Gravity: Edge 540FP: Approximately 80-90mm from wing root LE... -
Page 12: Limited Warranty
Edge 540 FP Instructions LIMITED WARRANTY Warranty Coverage Flex Innovations LLC and its authorized resellers (“Flex”) warrant to the original purchaser that this product (the “Product”) will be free from defects in materials and workmanship at the date of purchase. Outside of Coverage...