Yamaha LS9 Service Manual page 209

1.4 PROGRAM CHANGE
Reception
If [PROGRAM CHANGE ECHO] is ON, bank select messages will also be
echoed from MIDI OUT.
If SINGLE CH is selected, these messages are received if [PROGRAM CHANGE
Rx] is ON and the [Rx CH] matches. However if [OMNI] is ON, these messages
are received regardless of the channel. When these messages are received, scene
memory and effect library are recalled according to the settings of the
[PROGRAM CHANGE EVENT LIST].
Transmission
If [PROGRAM CHANGE Tx] is ON, these messages are transmitted according
to the [PROGRAM CHANGE Table] settings when scene memory and effect
library are recalled.
If SINGLE CH is selected, these messages are transmitted on the [Tx CH]
channel.
If the recalled scene memory and effect library has been assigned to more than
one PROGRAM NUMBER, the lowest-numbered PROGRAM NUMBER for
each MIDI channel will be transmitted.
PROGRAM CHANGE messages are not used for transmission to LS9 Editor
because there is no guarantee that the contents of the assignment tables will
match. (PARAMETER CHANGE messages are always used.)
Y ou can choose either MULTI MIDI CH or SINGLE CH.
If SINGLE is selected
Y ou can choose the Rx CH, OMNI CH, and Tx CH.
Y ou can choose whether a bank select message will be added.
A bank of up to 16 can be specified.
If MULTI is selected
The Rx and Tx channels will be the same.
The assignment table will use the settings for each MIDI channel. Bank select
messages will not be added.
Y ou can make settings for up to sixteen MIDI channels.
Program change
STATUS 1100nnnn Cn
DATA 0nnnnnnn nn Program number (0-127)
2 SYSTEM REALTIME MESSAGE
2.1 SONG SELECT
Select the track number shown in the TITLE LIST screen of the USB memory
recorder.
Song select
STATUS 11110011 F3
Song number 0sssssss ss Song number (0-127)
2.2 TIMING CLOCK
Reception
This message is used to control effects. This message is transmitted twenty-four
times per quarter note.
Echoing of this message depends on the OTHER item in the ECHO settings.
STATUS 11111000 F8 Timing clock
2.3 ACTIVE SENSING
Reception
Once this message has been received, MIDI communication will be initialized
(e.g., Running Status will be cleared) if no message is received for an interval of
400 ms.
This message is not subject to echoing.
STATUS 11111110 FE Active sensing
2.4 SYSTEM RESET
Reception
When this message is received, MIDI communication will be initialized (e.g.,
Running Status will be cleared).
This message is not subject to echoing.
STATUS 11111111 FF System reset
3 SYSTEM EXCLUSIVE MESSAGE
(Cn)
3.1 MMC
< MMC STOP >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and stops.
STATUS
ID No.
Device ID
COMMAND
EOX
< MMC PLAY >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and starts playback.
STATUS
ID No.
Device ID
COMMAND
EOX
< MMC DEFERED PLAY >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and starts playback.
STATUS
ID No.
Device ID
COMMAND
EOX
< MMC RECORD STROBE >
(F3)
Reception
If the [DEVICE NO.] matches or is 7F, receives this message, and if stopped,
starts recording.
STATUS
ID No.
Device ID
(F8)
COMMAND
EOX
< MMC PAUSE >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message, and if playing,
(FE)
pauses.
STATUS
ID No.
Device ID
COMMAND
EOX
(FF)
11110000 F0 System exclusive message
01111111 7F Real time System exclusive
0ddddddd dd Destination (00-7E, 7F:all call)
00000110 06 Machine Control Command(MCC) sub-id
00000001 01 Stop(MCS)
11110111 F7 End of exclusive
11110000 F0 System exclusive message
01111111 7F Real time System exclusive
0ddddddd dd Destination (00-7E, 7F:all call)
Machine Control Command(MCC) sub-id
00000110 06
00000010 02 Play(MCS)
11110111 F7 End of exclusive
11110000 F0 System exclusive message
01111111 7F Real time System exclusive
Destination (00-7E, 7F:all call)
0ddddddd dd
00000110 06 Machine Control Command(MCC) sub-id
00000011 03 Deferred Play(MCS)
11110111 F7 End of exclusive
11110000 F0 System exclusive message
01111111 7F Real time System exclusive
0ddddddd dd Destination (00-7E, 7F:all call)
00000110 06 Machine Control Command(MCC) sub-id
00000110 06 Record strobe
11110111 F7 End of exclusive
11110000 F0 System exclusive message
01111111 7F Real time System exclusive
0ddddddd dd Destination (00-7E, 7F:all call)
00000110 06 Machine Control Command(MCC) sub-id
00001001 09 Pause(MCS)
11110111 F7 End of exclusive
LS9-16/LS9-32
209