Yamaha LS9 Service Manual page 197

Message
Parameter xxx was copied to the copy buffer.
xxx Parameters Copied.
Parameter xxx was initialized.
xxx Parameters Initialized.
Parameter xxx was pasted from the copy buffer.
xxx Parameters Pasted.
Parameter xxx was swapped with copy buffer contents.
xxx Parameters Swapped with
Copy Buffer.
Assignment of more than 8 sources was attempted though the maximum
Assignment is Restricted to Max.
number of sources selectable with the Monitor Define function is 8.
8 Sources!
You attempted to recall a library of a different type.
Cannot Recall to Different
Parameter Type!
Failed to recall a scene memory or library.
Cannot Recall!
You attempted to select a channel that cannot be operated
Cannot Select This Channel.
due to your user level or some other reason.
A scene memory or library could not be stored.
Cannot Store!
You pressed the [UNDO] button when Undo was not avail-
Cannot Undo!
able.
File on the USB memory could not be accessed for some
Couldn't Access File.
reason.
File could not be saved from the USB memory.
Couldn't Write File.
Current user was changed to [xxx].
Current User Changed. [xxx]
You attempted to delete a directory, but failed because there
Directory Not Empty!
were files remaining in the directory
CUE was turned off because you switched from the RACK
EFFECT CUE: Turned Off.
screen to a different screen.
External HA connection status is different so that External HA
External HA Connection Conflict!
data cannot be recalled.
The following operation has not been performed yet because
File Access is Busy!
the USB memory is being accessed.
The USB memory already contains a file/directory with the same
File Already Exists!
name as the one you are attempting to save, rename, or create.
nternal file access error
File Error [xx]!
Meaning
EQ/DYNAM CS/GEQ/EFFECT were copied
EQ/DYNAM CS/GEQ/EFFECT were initialized
EQ/DYNAM CS/GEQ/EFFECT were pasted
EQ/DYNAM CS/GEQ/EFFECT were compared
←
←
· Recall of an empty SCENE or SCENE #0 was tried by assign-
ing SCENE NC/DEC RECALL to USER DEF NED KEY
Recall of a non existent SCENE or L BRARY number was
tried through MIDI command, etc.
←
The SCENE/L BRARY number selected as storing destina-
tion is wrong.
· UNDO was attempted using STORE UNDO key or USER
DEF NED KEY to which RECALL UNDO was assigned but in
vain because RECALL/STORE was not executed before that
· No access was performed because of reasons such as
non existence of the F LE
· Writing was unsuccessful.
←
· Deletion of a directory was tried though there is a file in the
directory.
←
The external HA data can not be recalled because SLOT
setting for STORE and current setting are different.
· When the ACCESS indicator in the top right of the screen is
still lighting, an operation for another file was tried.
The file/directory name just inputted is the same as the
existing file/directory name
· Creation of the CREATE USER KEY was tried though the
USB memory device is protected.
· The memory device was removed during file access was
performed.
· The internal file system detected an error for some reason.
Cause
—
—
—
—
· Cancel the currently selected sources and select
other sources.
—
—
—
—
—
· Try accessing the file with a PC.
· Check for write-protect, and use a PC to check if
the USB device is not defective.
· Backup the data, format with the main unit or PC,
then return the backup data and save again.
—
· Delete all the files in the directory and then delete
the directory.
—
Set the current setting back to the SLOT setting
when the data was stored.
· Store the data again.
· Wait until the ACCESS indicator in the top right of the
screen turns off before performing another operation.
· Input another name.
f [ /O Error is shown probably the USB memory
was removed during file access and the file was
damaged. In this case, there is no countermea-
sure.
Coping process