EPOMAKER Skyline 87 - TKL Hot-Swap Wireless Mechanical Keyboard Manual

Also See for Skyline 87:

Quick start manual (18 pages)

Table of Contents

Contents

1 SHORTCUTS
2 CONNECTION
3 BACKLIGHT SETTINGS
4 CHANGE RGB EFFECTS
5 PAIRING BLUETOOTH
6 PAIRING WIRELESS 2.4 GHz
7 RECONNECTION INSTRUCTION
8 PRODUCT SPECIFICATIONS
9 REPLACING KEYCAPS AND SWITCHES
10 TECHNICAL ASSISTANCE
11 Documents / Resources
- 11.1 References
- 11.2 Download manual

EPOMAKER Skyline 87 - TKL Hot-Swap Wireless Mechanical Keyboard Manual

SHORTCUTS

FN + F1	Screen brightness -
FN + F2	Screen brightness +
FN + F3	Task switching (WIN+Tab)
FN + F4	Quick Access
FN + F5	Email
FN + F6	My Computer
FN + F7	Last song
FN + F8	Pause/Play
FN + F9	Next Song
FN + F10	Mute
FN + F11	VOL -
FN + F12	VOL +
FN+ ESC	Restore the default setting
FN+ WIN	Lock Windows
FN+ ENTER	Battery Status

CONNECTION

FN + 1	Bluetooth Device 1 Short press to switch, long press 3S to enter Bluetooth device 1
FN + 2	Bluetooth Device 2 Short press to switch, long press 3S to enter Bluetooth device 2
FN + 3	Bluetooth Device 3 Short press to switch, long press 3S to enter Bluetooth device 3
FN + 4	Wireless 2.4G Long press 3S to enter 2. 4G mode
FN + 5	USB-C Short press to switch to wired connection

BACKLIGHT SETTINGS

FN + ↑	RGB Brightness +
FN + ↓	RGB Brightness -
FN + ←	RGB Speed -
FN + →	RGB Speed +
FN + INSERT	Toggle the backlight mode
FN + HOME	Toggle the backlight color
FN + PG UP	Toggle backlight direction
FN + BACKSPACE	Turn on/off the RGB

CHANGE RGB EFFECTS

Pressing Fn+Insert at the same time allows you to switch the RGB effect of your Skyline 87 keyboard kit.

PAIRING BLUETOOTH

Long press the FN+1/2/3 for 3S, the keyboard will start pairing, the light will flash and stay on 2S. If there's no connection, the keyboard will enter sleep mode.

PAIRING WIRELESS 2.4 GHz

Firstly, turn on the keyboard, press FN+4 to enter 2.4G mode, then press FN+4 key combination 3S to enter pairing mode, plug the receiver into your device, and you will see the light flashes, then exit pairing after successful recognized, the mode LED is always on for 2S, after the 30S, exit pairing mode, the light goes off, and the keyboard goes to sleep.

RECONNECTION INSTRUCTION

When the keyboard is turned on or wakes from sleep mode, only the current device will be reconnected; if the reconnection is unsuccessful, it will go to sleep, and will continue to reconnect after the key is woken up.
The indicator light flashes slowly when reconnecting with Bluetooth, and is always on for 2S after connection. If you press the button during reconnection, the reconnection time will become longer. Counting within 10S after releasing the button, if the pairing is successful, the keyboard will enter pairing mode. If the reconnection fails, the light will go off and the keyboard will enter sleep mode, but the data of the last successful pairing will be retained.

PRODUCT SPECIFICATIONS

NUMBER OF KEYS	87 KEYS
HOT-SWAP	YES
BACKLIGHT	RGB BACKLIGHT
CONNECTION	BLUETOOTH 5.0/2.4GHZ/TYPE-C WIRED
COMPATIBILITY	WINDOWS/MAC
BATTERY	4000mAh
PRODUCT WEIGHT	0.9kg
PRODUCT DIMENSIONS	360 x 170 x 35 mm

REPLACING KEYCAPS AND SWITCHES

For a full guide on how to remove keycaps and switches scan the QR Code or type in your browser: https://epomaker.com/blogs/guides/diy-guide-how-to-remove-and-replace-your-mechanical-keyboard-switches

Before installing switches, be sure the pins are clean and straight.

Push Straight Down
Please be gentle. Be sure the pins are aligned with the slots.

Included Tools

Mechanical Switch
Example of a switch as seen from top after you remove the keycap to prepare for switch removal.

The Switch Puller tool aligns Vertically to the Switch to unclip the plastic securing the switch to the plate.

Remove Switches

Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

Check that all the switch metallic pins are perfectly straight and clean.
Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
Inspect the switch to ensure it's properly attached to your keyboard, and test it.

caution Note: If the key doesn't work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.
Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, please email to support@epomaker.com with your purchase order number and a detailed description of your issue.
We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, please contact them directly for any additional help.

COMMUNITY FORUMS
Join our community and learn together with other keyboard enthusiasts.
https://discord.gg/2q3Z7C2
https://www.reddit.com/r/Epomaker/

Made in China
Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road, Xili Street, Nanshan Disctrict, Shenzhen, Guangdong, CN
Email: support@epomaker.com
Web: www.epomaker.com

APEX CE SPECIALISTS LIMITED
Address: UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD CORK, T23 AT2P, IRELAND
Contact: Wells
Tel: +353212066339
Email: info@apex-ce.com