Roland M-GS64 Owner's Manual page 76

When this message is received, Rx.HRPN will set OH.
This message will not be received when "SysEx" parameter of "MIDI Rx Sw" group = OFF.
'Moke on interval of S0ms or more, hefore receiving the next message.
it GS mode
This model will be in un operational mode of "Patch Table 1" when receiving this message.
'Status Data byte Status
FOH 41H, dev, 42H, 12H, 40H, OOH, 7FH, 7FH, 424 FH
Byte Description
FOH Exclusive status
a 'D number (Roland)
dey Device 1D (dev: OON — 1FH (1 — 32), Initial value is 10H {17)}
42H Model IB (6S)
TH Command 1D (O11)
AGH Address MSB
OOH Address
TH Address LSB
TH Data {Exit 6S mode)
42H Check sum
ETH EDX (End OF Exclusive)
This message wl not be received when "Exclusive" parameter of MIDI Rx Sw" group = OFF.
Make an interva! of 5Oms or mare, before receiving the next message.
2. TRANSMIT DATA
System realtime
° Active sensing
status
FEH
This message i transmitted with 250 mili seconds interval,
© System exclusive message
status dota bytes
FOH iH, ddk,...eeH
FH
FOH: System exclusive
manufacturer #0: 41H (65)
dd, ..., ee = Dota: OOH — 7FH (0 — 127}
FTH: FOX (End of Exclusive/System common)
Refer fo section 3,4.
3. Exclusive communications
The Sound Expansion Series can send ond receive paich parameter, elc using the system exclusive message.
The model 1D code of the Sound Expansion Series s 46H. The device ID code is to be determined by the "Device 10"
setting of Master.
The Sound Expansion Series ignores GS exclusive message other than "GS reset," "Exit 6S made" and "Scale tune
poramefer," General MIDI system on, General MIBI system off, GS reset and Exit 65.
The model iD of the G5 is 42H.
One way communication.
* Request data 1 RQT (11H)
Bytes Description
Fol Exclusive status
4a Manufocturer 1D (Roland)
Dev Device 1D
46H Model 1D {Sound Expansion Series}
a Commond 1D (RQ.1)
cal Address MSB
bbH Address
ccH Address
ad Address LSB
ss Size MSB
tH Size
wut Size
wit Size LSB
sum Check sum
FH FOX {End of exclusive)
Receive only: the Sound Expansion Series does not send this message.
MIDI IMPLEMENTATION
12H
Sound Expansion Series (MODEL ID = 46H)
Manufacturer (0 (Roland)
4qH
Dev Device 1D
46H Model 1D
12H Command ID (DT 1}
ail Address MSB
bhH Address
cl Adress
dd Address SB
eel! Dota
ff Data
sum Check sum
FH £OX {End of exclusive)
2. GS (MODEL ID = 42H)
Bytes Description
FOH Exclusive status
4i Manufacturer (0 (Roland}
Dev Device ID
4a Model ID (GS)
v2H Command ID (DTH)
onl Address MSB
bbq Address
cH Address
col Data
HH Data
sum Check sum
FH EOX (End of Exclusive)
Note: When the device {D is 7FH, Sound Expansion Series con receive the exclusive message even if the unit number
is enything,
* Parameter address map
Address and size are configured in 7 bits, hexcdecimal notation.
Address SB iB
Binary Gooa nega §— Ohbb bbb eee cee Odd ddd
Phitshex AK BB ice BD
Size ASB LSB
Binary sss ssss Ott HH Quy uuu = Gv wwe
Thitshex SS ais UU Ww
¢ Parameter base address
1) A pair of two addresses preceded by the symbol # represents a divided — by -two dats, e.g.the dota ABH (hex) is
divided into OAH ond OBH and seat in that order.
2) Porameter associated with address following the symbol % are for Sound Expansion Series
* Example of exclusive data
Dita Set I (1 byte dota)
To Select Pan-Delay for the Reverb Type.
FO 41 10 46 1206 00 10 OB 07 SC FT
Note that the Sth byte value is 12H in order fo "Set" the date,
Send the data (07 for Pon-Delay) with the address (00 00 01 OD for reverb type) of the "Performance common"
porometer.
Data set 1 (2 byte data)
To Select Wave Number 141 for Patch Tone 1 in Past 1.
FO 4] 10 46 12:00 00 28 01 08 0C 43 F7
The Address For Patch Tone 1 in Part | is 00 00 28 01.
If you wont to send 140 as a data, first you need to change it to hex-decimal notation which is BC.
Then divide this in 2 byte, which is called "nibblizing" , and send 08 OC os data.
Request Data
Hake the module to send the chorus level.
FO 41 10 46 11 00-00 10 12 00:00:90 01 5D F7
Hote that the Sth byte value is 17H, in order to "Request" the date.
'Send 00 69 10 12 as an Address for Chorus Level and 00 00 00 O1 as "Size of the data" for it, which is 1 byte.
'When the module receives this data, it will automatically send bock the following data from MIDI OUT.
FO 41 10 46 1200 00 10 12 3 22 7
15