Advertisement
Before requesting
service, make the following checks. If you are in doubt about some of the check points, or if the solutions
indicated in the chart de not
solve the problem, refer to "Customer
Services Directory" on page 38 if you reside in the U.S.A., or refer to "Product information"
on page 32 if you
reside in Canada.
In other areas, consult your dealer.
I".tI_FJ2Jl
No power.
• Insert the AC power supply cord securely.
181
1,01
The unit is automatically
switched
• The Sleep timer was working and had reached the set time limit.
to standby
mode.
The display
is dark,
• Select "Bright" in "FL Dimmer" in the "Others" menu.
25
"NOPLAY"
• You inserted a disc the unit cannot play; insert one it can.
12
• You inserted a blank disc.
• You inserted a disc that has not been finalized.
"NODISC"
• You have not inserted a disc; insert one.
• You have not inserted the disc correctly;
insert it correctly.
14
"F61"
• Check and correct the speaker cable connections.
7
If this does net fix the problem, consult the dealer.
"F76"
• There is a power supply problem. Consult the dealer.
--
"DVD Ul1"
• Disc may be dirty. Wipe it clean.
13
"ERROR"
• Incorrect operation
performed.
Read the instructions
and try again.
--
"DVD H_"
• Trouble may have occurred, The numbers following "H" and "F" depend on the status of the unit.
--
"DVD FD_"
Turn the unit off and then back on. Alternatively,
turn the unit off, disconnect
the AC power supply
D stands for a number,
cord, and then reconnect
it.
• If the service numbers fail to clear, note the service number and contact a qualified
service person.
--
" _
" or " _
" is flashing.
• _
and _
are the wireless
link indicators
for the optional wireless accessories:
SH-FX65
and
--
SH-FX85
respectively.
The flashing will stop after a while.
"U70_"
• The HDMI connection
acts unusually.
D stands for a number,
-The
connected
equipment
is net HDMI-compatible.
The actual number following "U70"
- Please use HDMI cables that have the HDMI logo (as shown on the cover).
will depend on the state of the main
- The HDMI cable is too long.
unit.
-The
HDMI cable is damaged.
--
"XM RADIO"
• It takes a short time for the XM radio to power up after turning on the main unit, during which time
--
"XM RADIO" is displayed
(only when the selected source is XM).
Wait a few seconds for this process to complete.
"XM ERROR"
• There may be an error in the XM radio module. Turn the main unit off, and then back on.
--
• The XM antenna may be defective.
Consult the dealer of the XM antenna.
"REMOTE
1" or "REMOTE
2"
• Match the modes on the main unit and remote control. Depending on the number being displayed ("1"
10
or "2"), press and hold [ENTER] and the corresponding numbered button ([1] or [2]) for at least 2
seconds.
No response
when any buttons
• This unit cannot play discs other than the ones listed in these operating instructions.
12
are pressed.
• The unit may net be operating properly due to lightning, static electricity or some other external
--
factor. Turn the unit off and then back on. Alternatively,
turn the unit off, disconnect
the AC power
supply cord, and then reconnect
it.
• Condensation
has formed. Wait 1 to 2 hours for it to evaporate.
No response
when remote
control
• Check that the batteries are installed correctly.
9
buttons
are pressed,
• The batteries are depleted.
Replace them with new ones.
9
• Aim the remote control at the remote control signal sensor and operate.
11
Other products
respond
to the
• Change the remote control operating mode.
10
remote control.
Cannot play DVDs,
No picture or sound,
You have forgotten
your ratings
password,
Reset all the settings to Factory
Preset.
The EZ Sync"HDAVl
Control"
function
does not respond.
• CD Mode is on. Press and hold [--CD
MODE] to turn CD Mode off.
16
• Check the video or speaker connection.
6, 7
• Check the power or input setting of the connected
equipment and the main unit.
• Check that the disc has something
recorded on it.
• While stopped and "DVD/CD" is the source, press and hold [11] (Stop) on the main unit and [> 10]
on the remote control until "Initialized"
disappears
from the television.
Turn the unit off and on
again.
All settings will return to the default values.
• Depending on the condition of the home theater system or the connected
equipment,
it may be
26
necessary to repeat the same operation so that the function can work correctly.
o
(Continued
on next page)
x
Advertisement
