Monoprice BLACKBIRD 44556 User Manual
  1. Manuals
  2. Brands
  3. Monoprice Manuals
  4. Switch
  5. BLACKBIRD 44556
  6. User manual

Monoprice BLACKBIRD 44556 User Manual

4k60 seamless hdmi 2.0
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Blackbird™ by Monoprice™
4K60 Seamless HDMI
®
2.0
4X4 MATRIX
44556
P/N
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BLACKBIRD 44556 and is the answer not in the manual?

Questions and answers

Related Manuals for Monoprice BLACKBIRD 44556

Summary of Contents for Monoprice BLACKBIRD 44556

  • Page 1 Blackbird™ by Monoprice™ 4K60 Seamless HDMI ® 4X4 MATRIX 44556 User Manual...
  • Page 2 Thank You for Purchasing this Product To ensure optimum performance and safety, read the following instructions before connecting, operating, or adjusting the product. Keep this manual for future reference. Surge Protection Device Recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shocks, lightning strikes, etc.

  • Page 3: Table Of Contents

    • Do not block or cover these openings. Ensure that the device is in an open area where it can get sufficient airflow to keep from overheating. • Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred. •...

  • Page 4: Introduction

    1. Introduction The 4K60 4:4:4 HDMI matrix is a versatile and high-speed video processing system that serves multiple purposes. This system has two output modes that can be configured according to your needs. It can operate as a 4x4 seamless matrix switcher or a 2x2, 4x1, or 1x4 video wall solution, among others.

  • Page 5: Package Contents

    3. Package Contents • 1 × 18Gbps 4×4 Seamless Matrix • 1 × Matrix IR Remote • 1 × 3pin-3.81mm Phoenix Connector (male) • 1 × 20-60KHz IR Wideband Receiver Cable (1.5 meters) • 2 × Mounting Ears • 4 × Machine Screws (KM3*4) •...

  • Page 6: Ir Remote

    Rear Panel INPUT OUTPUT TCP/IP RS-232 IR EXT HD 1 HD 2 HD 3 HD 4 HD 1 HD 2 HD 3 HD 4 DC 12V Name Function Description The link port for TCP/IP control, connected to an active Ethernet TCP/IP link with an RJ45 cable to control the Matrix via Web.
  • Page 7 OUTPUT 1/2/3/4: Press these buttons to select the output source. All: Select all output source simultaneously. For example, when you press the “All” button and then press input “1” button, at this time the input “1” source will output to all display devices. Res: Press this button to switch output channel resolution.

  • Page 8: Ir Cable Pin Assignment

    6. IR Cable Pin Assignment IR RECEIVER IR Signal Grounding Power 12V IR RECEIVER Note: When the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ±...

  • Page 9: Video Wall

    The defined EDID setting list of the product is shown as below: EDID EDID EDID Description EDID Description Mode Mode 4k2k60_444,stereo audio 2.0 1920x1200,stereo audio 2.0 4k2k60_444,dolby/dts 5.1 1360x768, stereo audio 2.0 4k2k60_444,hd audio 7.1 1024x768, stereo audio 2.0 4k2k30_444,stereo audio 2.0 user define1 4k2k30_444,dolby/dts 5.1 user define2...
  • Page 10 Step 1 Get the current IP Address. The default IP address is 192.168.0.100. You can get the current Matrix IP address in two ways: The first way 1: You can get the IP address via panel buttons. On the initial OLED display, press the “MENU”...
  • Page 11 After entering the Web GUI page, there will be a Login page, as shown below: Select the Language from the drop-down list to choose English or Simple Chinese. Select the Username from the list and enter the password. The default passwords are: Username : User Admin Password: user admin After entering the password, click the “LOGIN”...
  • Page 12 Input Page You can do the following operations on the Input page: 1. Inputs: Input channel of the device. 2. Active: It indicates whether the channel is connected to a signal source. When the input port is connected to the signal, it shows green, otherwise, it shows gray.
  • Page 13 6. Download the EDID File for the Corresponding Input Channel Click the drop-down box of “Select EDID File” to select the corresponding input channel. Then click “Download” to download the corresponding EDID file. Output Page You can do the following operations on the Output page: 1.
  • Page 14 Video Mode Page You can do the following operations on the Video Modepage: 1. Matrix: Click to select Matrix mode. 2. Video Wall: Click to select any multiview display mode. 3. Matrix/Video Wall Adjustment: Display the input and output information. 4.
  • Page 15 Network Page You can do the following operations on the Network page: Modify Network Setting Modify the IP Mode Address/Gateway/Subnet Mask/Telnet Port as required, click “Save” to save the settings, then it will come into effect. After modification, if the Mode is “Static”, it will switch to the corresponding IP Address;...
  • Page 16 Note: Input rules for changing passwords: (1) The password can’t be empty. (2) New Password can’t be the same as Old Password. (3) New Password and Confirm Password must be the same. Set the Default Network Click “Set Network Defaults” button, there will be a prompt, as shown in the following figure: Click “OK”...

  • Page 17: Rs-232 Control Command

    System Page You can do the following operations on the System page: 1. Panel Lock: Click to lock/unlock panel buttons. “On” indicates that panel buttons are unavailable; “Off” indicates panel buttons are available. 2. Beep: Click to turn on/off the beep. 3.
  • Page 18 Then open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as below. ASCII Command Serial port protocol. Baud rate: 115200(default), Data bits: 8, Stop bits: 1, Check bit: 0 x - Parameter 1 y - Parameter 2 ! - Delimiter...
  • Page 19 Command Function Default Example Feedback Code Description Setting System Setting reboot… system initializing... s reboot! Reboot the device s reboot! initialization finished! mcu fw version x.xx.xx reset to factory defaults system Reset to factory s reset! s reset! initializing... defaults initialization finished! mcu fw version x.xx.xx Output setting...
  • Page 20 Default Command Code Function Description Example Feedback Setting Output setting Get output y resolution(y=0~4) output 1 y=0. output all s output 1 resolution: r output y res! y=1. output 1 csc 1! s output 1 csc 1! y=2. output 2 3840x2160p60 y=3.
  • Page 21 Command Function Description Example Feedback Default Setting Code Output Setting Get output y hdcp status.(y=0~4) y=0. output all r output y r output 1 output 1 hdcp: y=1. output 1 hdcp! hdcp! hdcp 1.4 y=2. output 2 y=3. output 3 y=4.
  • Page 22 Command Function Description Example Feedback Default Setting Code Output Setting Set output y stream enable/disable (y=0~4, x=0~1) y=0. output all s output y s output 1 y=1. output 1 output 1 stream: stream enable stream 1! y=2. output 2 enable y=3.
  • Page 23 Command Default Function Description Example Feedback Code Setting EDID Setting Set hdmi input x edid mode (x=0~4,z=1~18) x=0. all input x=1. input1 x=2. input2 x=3. input3 x=4. input4 z=1. 4k2k60_444,stereo audio 2.0 z=2. 4k2k60_444,dolby/dts 5.1 z=3. 4k2k60_444,hd audio 7.1 input 2 edid: z=4.
  • Page 24 Command Default Function Description Example Feedback Code Setting Video Wall setting Set tv wall display mode(x=1~10) x=1. 2x2 mode x=2. 2x1 mode x=3. 2x1-2 mode x=4. 1x2 mode s tw mode tv wall s tw mode x! tv wall mode: 2x2 x=5.
  • Page 25 Command Function Default Example Feedback Code Description Setting Video Wall setting Set tv wall resolution (x=1~15) 1. 4096x2160p60, 2. 4096x2160p50, 3. 3840x2160p60, 4. 3840x2160p50, 5. 3840x2160p30, 6. 1920x1080p60, tv wall resolution: s tw res x! 7. 1920x1080p50, s tw res 3! 3840x2160p60 3840x2160p60 8.
  • Page 26 Command Function Default Example Feedback Code Description Setting Network Setting set ip address: 192.168.0.100 (please use "s net s ip addr reboot!" command or Set network ip s ip addr xxx.xxx. repower device to address 192.168.0.100! xxx.xxx! apply new config!) dhcp on, device can't config static address, set dhcp off first.

  • Page 27: Application Example

    Command Default Function Description Example Feedback Code Setting Network Setting r telnet port! Get network telnet port r telnet port! telnet port:23 Network reboot… IP Mode: Static IP: 192.168.1.72 Subnet Mask: 255.255.255.0 s net reboot! Reboot network modules s net reboot! Gateway: 192.168.1.1 TCP/IP port=8000 Telnet port=10...

  • Page 28: Specifications

    12. Specifications Technical HDMI Compliance HDMI 2.0b HDCP Compliance HDCP 2.2 and HDCP 1.4 Video Bandwidth 594MHz/18Gbps Input: VGA-WUXGA (up to 1920×1200@60Hz), 480i-4K (3840x2160@60Hz 4:4:4, 4096x2160@60Hz 4:4:4) Output: 4096x2160p60, 4096x2160p50, 3840x2160p60, Video Resolution 3840x2160p50, 3840x2160p30, 1920x1080p60, 1920x1080p50, 1920x1080i60, 1920x1080i50, 1920x1200p60rb, 1360x768p60, 1280x800p60, 1280x720p60, 1280x720p50, 1024x768p60, auto Color Space RGB, YCbCr 4:4:4/4:2:2, YUV 4:2:0...
  • Page 29 You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at support@monoprice.com. Check the website for support times and links.
  • Page 30 Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Monoprice™ and all Monoprice logos are trademarks of Monoprice Inc.
  • Page 31 1 Pointe Drive, Suite 400 Brea, CA 92821 – USA Product pictures are for reference only. Specifications described herein are subject to change www.monoprice.com without prior notification. Monoprice™ and all Monoprice logos are trademarks of Monoprice Inc. Copyright © 2023 Monoprice, Inc. All rights reserved.

Table of Contents