Keystone KSTAP10PINV User Manual page 23

Mode Button
· Selects the desired operating mode. Each time you
press the button, a mode is selected in a sequence
that goes from AUTO, COOL, DRY, FAN and HEAT
(Heat models only). The mode light illuminates and
indicates the selected mode.
Up ( ) and Down ( ) Buttons
· Used to increase/decrease temperature settings in
1° increments in a range of 60°F/16°C to 86°F/30°C
or the TIMER setting in a range of 0 ~ 24hrs.
· To change between °F or °C, simultaneously press
and hold the Up and Down buttons for 3 seconds.
Fan Button/Continuous fan(On some models) button
· Controls the fan speed. Press to control the fan
speed in four steps - LOW, MID, HIGH and AUTO.
The selected fan speed light will illuminate.
NOTE: Applicable to models with the Constant
Fan feature. In COOL or DRY mode, press the Fan
button for 3 seconds to turn on or off the constant
fan function.
When the function is turned on, the constant fan
light will illuminate, indicating the fan will run
constantly. When the function is turned off, the
constant fan light will go out, indicating that the
fan will stop when the compressor stops.
Sleep Button
· Used to initiate the SLEEP operation.
· Pressing this button will increase (during
cooling operation) or decrease (during heating
operation, applicable models) 2°F/1°C after 30
minutes. The temperature will again increase
(cooling) or decrease (heating) by another
2°F/1°C after an additional 30 minutes. This
new temperature will be maintained for 7
hours before returning to the originally sele-
cted temperature. This ends the Sleep mode
and the unit will continue to operate as orig-
inally programmed.
· Press SLEEP button for
the filter feature.This feature is a reminder to
clean the Air Filter for more efficient operation.
The LED(the light above the button) will illumi-
nate after 250 hours of operation.
加阻抗声明机型，其它无不合格要求的机型可以直接删除此内容，
3 seconds to initiate
Air Magicfeature(on some models)
· Press SWING button and TIME button at
the same time for 3 seconds to initiate Air Magic
feature and the Air Magic light illumiantes, the
LED DISPLAY shows 'On' for 3 seconds for some
units. Press it for 3 seconds again to stop the
Air Magic feature and the Air Magic light turn
dark, the LED DISPLAY shows 'OF' for 3 seconds
for some units.
UV feature(on some models)
· Press SWING button and TIME button at the
same time for 3 seconds to initiate UV-C lamp
feature and the UV light illumiantes, the LED
DISPLAY shows 'On' for 3 seconds for some
units. The UV-C lamp feature will help to
purify the air inside. Press it for 3 seconds
again to stop the UV-C lamp feature and the
UV light turn dark, the LED DISPLAY shows
'OF' for 3 seconds for some units.
LED Display
· Shows the set temperature in °F (Degrees
Fahrenheit)("°F" no display for some models)
or °C (Degrees Celsius) and the Auto-timer
settings. While on DRY and FAN modes, it
shows the room temperature.
· Shows Error codes and protection code:
The unit may stop operation or continue to
run safely. If the error codes appear, wait for
about 10 minutes. The problem may resolve
itself. If not, disconnect the power, then
connect it again. Turn the unit on. If the
problem persists, disconnect the power and
contact your nearest customer service center.
Error code appears andbegins with the
letters as the following in the window
display of indoor unit:EH(xx), EL(xx), EC(xx),
PH(xx), PL(xx), PC(xx)
P1-Bottom tray is full--Connect the drain hose
and drain the collected water away.If protection
repeats,call for service.
Note: When one of the above malfunctions
occurs, turn off the unit, and check for any
obstructions. Restart the unit, if the malfunction
is still present, turn off the unit and unplug the
power cord. Contact the manufacturer or its
service agents or a similar qualified person for
service.
Page 19
 