Related Manuals for SCHUNK CLM
Summary of Contents for SCHUNK CLM
- Page 1 Assembly and operating manual CLM Compact Linear Module Translation of the original manual...
- Page 2 Imprint Imprint Copyright: This manual is protected by copyright. The author is SCHUNK SE & Co. KG. All rights reserved. Technical changes: We reserve the right to make alterations for the purpose of technical improvement. Document number: 389015 Version: 05.00 | 13/02/2024 | en...
-
Page 3: Table Of Contents
2.12.4 Protection against electric shock............ 14 2.13 Notes on particular risks ............... 15 3 Technical Data ..................16 4 Assembly and Settings ................17 4.1 Mechanical connection................. 17 4.2 Pneumatic connection................17 05.00 | CLM | Assembly and operating manual | en | 389015... - Page 4 8 Translation of the original declaration of incorporation ......... 33 9 UKCA declaration of incorporation ............34 10 Information on the RoHS Directive, REACH Regulation and Substances of Very High Concern (SVHC) ..................35 05.00 | CLM | Assembly and operating manual | en | 389015...
-
Page 5: General
Dangers for persons! Non-observance can lead to irreversible injury and even death. CAUTION Dangers for persons! Non-observance can cause minor injuries. CAUTION Material damage! Information about avoiding material damage. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 6: Definition Of Terms
1.3 Scope of delivery The scope of delivery includes Compact Linear Module CLM in the version ordered Stop collar (CLM08) End position damping (CLM10 - CLM 200) 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 7: Accessories
WARNING The rod lock is not a safety component for personal protection in the sense of the Machine Directive. Exact specifications and ordering data ☞ catalog. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 8: Stop Screw
For size CLM 08 a stop is optionally available with integrated sensor. End stop without sensor system LMAS 08-KT (included in the scope of delivery) End stop with sensor system NIA 50-KT 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 9: Basic Safety Notes
Use only original spare parts or spares authorized by SCHUNK. 2.5 Ambient conditions and operating conditions Required ambient conditions and operating conditions 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 10: Personnel Qualification
When working on and with the product, observe the occupational health and safety regulations and wear the required personal protective equipment. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 11: Notes On Safe Operation
When handling heavy weights, use lifting equipment to lift the product and transport it by appropriate means. Secure the product against falling during transportation and handling. Stand clear of suspended loads. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 12: Malfunctions
Have all work carried out by appropriately qualified personnel. For all work, secure the product against accidental operation. Observe the relevant accident prevention rules. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 13: Protection During Commissioning And Operation
Before starting up the machine or automated system, check that the EMERGENCY STOP system is working. Prevent operation of the machine if this protective equipment does not function correctly. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 14: Protection Against Electric Shock
The effectiveness of the potential equalisation must be verified by executing regular safety measurements. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 15: Notes On Particular Risks
For all work in the vicinity of hot surfaces, wear safety gloves. Before carrying out any work, make sure that all surfaces have cooled down to the ambient temperature. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 16: Technical Data
* For use in dirty ambient conditions (e.g. sprayed water, vapors, abrasion or processing dust) SCHUNK offers corresponding product options as standard. SCHUNK also offers customized solutions for special applications in dirty ambient conditions. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 17: Assembly And Settings
A linear movement must always be free of impact and bounce. For this purpose, carry out sufficient throttling and damping, [/ 24]. } 4.5 Observe the specifications in the catalog data sheet. 05.00 | CLM | Assembly and operating manual | en | 389015... - Page 18 Observe the requirements for the air supply } 3 [/ 16]. Compressed air connection CLM 08, 10 Compressed air connection CLM 25 – 100 (* for CLM 25: connection opposite) Air connection G1/8" G1/8" 05.00 | CLM | Assembly and operating manual | en | 389015...
-
Page 19: Adjust Stroke, Sensors And Damping
The following components are available for stroke limiting, shock absorption and monitoring of the end positions: Stop screw LMAS (option) Shock absorbers (included in the scope of delivery) 05.00 | CLM | Assembly and operating manual | en | 389015... - Page 20 Set shock absorber and proximity switch IN to the desired stroke. IMPORTANT! Do not fall below minimum distances X and Y. For CLM 10: Tighten counter nut. Tighten the attachment screw. ð Observe the tightening torque, see following table. 05.00 | CLM | Assembly and operating manual | en | 389015...
-
Page 21: Endlagen - Sets Clm 50 - 200
Loosen the attachment screw. sensor adjustment Set shock absorber stop LMST and proximity switch IN to desired stroke. Tighten the attachment screw. ð Observe the tightening torque, see following table. 05.00 | CLM | Assembly and operating manual | en | 389015... - Page 22 Adjust the damping adjustment setscrew to the desired dimension. IMPORTANT! Observe adjustment range Z! Secure the setscrew again. Size Damping adjustment range Z [mm] CLM 50 0...+1.8 CLM 100 -0.6...+2.4 CLM 200 -1.8...+1.8 05.00 | CLM | Assembly and operating manual | en | 389015...
-
Page 23: Setting The Speed
NOTE A smooth motion may also be too slow in many use-cases. Further settings can be made via the shock absorbers, } 4.5 [/ 24]. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 24: Adjustment Of The Shock Absorber Strocke
The shock absorber stroke is too short and the unit arrives in the end position too abruptly. Movement End position Damping Time T Target time Optimal shock absorber stroke. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 25: Mounting The Rod Lock
Cover plate (B) is no longer required. Install face plate I (C). Removing screw from air connection (1) ð Clamping is active and must be released by the appropriate air pressure. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 26: Commissioning
CAUTION Risk of mechanical damage of the product! Theproduct must always be adjusted so that no mechanical impacts are produced when reaching the end position. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 27: Troubleshooting
Change defective exhaust ait throttle if necessary. Bad damping. Adjust damping (stop screw). } 4 [/ 17] Unfavorable installation. Check construction. CLM size too small Use larger CLM size. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 28: Maintenance And Care
The product contains food-compliant lubricants as standard. The requirements of standard EN 1672-2:2020 are not fully met. NOTE Change contaminated food-compliant lubricant. Observe information in the safety data sheet from the lubricant manufacturer. 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 29: Assembly Drawings/Spare Parts
Item 04*, 14*, 25, 26, 27, 34, 35 * Item 04 (base body) and item 14 (guide rail) only available as pre-assembled assembly. Order numbers in the following example Part-No. 1 CLM 08 - H14 - 01 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 30: Clm 10
Item 04*, 14*, 25, 26, 27, 34, 35 * Item 04 (base body) and item 14 (guide rail) only available as pre-assembled assembly. Order numbers in the following example Part-No. 1 CLM 10 – H20 – 01 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 31: Clm 25
Wear parts Item 14, 25, 26, 27, 29, 34, 35 Order numbers in the following example Part-No. 1 CLM 25 – H025 – 01 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 32: Clm 50, 100 And 200
Wear parts Item 14, 26, 27, 28, 29, 34, 35, 38 Order numbers in the following example Part-No. 1 CLM 100 – H075 – 01 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 33: Translation Of The Original Declaration Of Incorporation
Person authorized to compile the technical documentation: Stefanie Walter, Address: see manufacturer's address Lauffen/Neckar, February 2024 Dr.-Ing. Manuel Baumeister, Head of Systems Engineering, Technology & Innovation 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 34: Ukca Declaration Of Incorporation
Person authorized to compile the technical documentation: Marcel Machado, address: refer to manufacturer's address Lauffen/Neckar, February 2024 Dr.-Ing. Manuel Baumeister, Head of Systems Engineering, Technology & Innovation 05.00 | CLM | Assembly and operating manual | en | 389015... -
Page 35: Information On The Rohs Directive, Reach Regulation And Substances Of Very High Concern (Svhc)
"on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS)", or fulfill their intended function only as part of one. Therefore products from SCHUNK do not fall within the scope of the directive at this time. REACH Regulation Products from SCHUNK fully comply with the regulations of Regulation (EC) No. 1907/2006... - Page 36 SCHUNK SE & Co. KG Toolholding and Workholding | Gripping Technology | Automation Technology Bahnhofstr. 106 - 134 D-74348 Lauffen/Neckar Tel. +49-7133-103-0 info@de.schunk.com schunk.com Folgen Sie uns I Follow us Wir drucken nachhaltig I We print sustainable...
Need help?
Do you have a question about the CLM and is the answer not in the manual?
Questions and answers