Related Manuals for Knightsbridge TNXQUADMWSTW
Summary of Contents for Knightsbridge TNXQUADMWSTW
- Page 1 INSTALLATION & MAINTENANCE MANUAL TNXQUADMWSTW/ TNXQUADMWSTBK TNXONEMWSTW/ TNXONEMWSTBK...
-
Page 2: General Instructions
These instructions should be used to aid installation of the following products: TNXQUADMWSTW / TNXQUADMWSTBK / TNXONEMWSTW / TNXONEMWSTBK SAFETY • This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. - Page 3 • Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP rated junction boxes should be used where required Remove the diffuser from the luminaire housing by unscrewing the four screws • Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not •...
-
Page 4: Sensor Layout
Attach the LED plate to the luminaire body by aligning the four butterfly screws on the body • Fig. 2 corresponding holes on the plate then turn clockwise to lock into place (see Fig. 3) Fig. 2 • Attach the LED plate to the luminaire body by aligning the four butterfly screws on the body with the corresponding holes on the plate then turn clockwise to lock into place (see Fig. -
Page 5: Dip Switch Settings
DIP SWITCH SETTINGS Detection area Hold time 100% 1min 3min 5min 10min 20min Daylight sensor 30min * When set to disable, the daylight 2Lux sensor will switch the light 10Lux on when motion is detected 25Lux regardless of the ambient light level 50Lux Disable*... -
Page 6: Self-Test Function
• Re-attach the diffuser to the luminaire body using the four screws • Switch on and check for correct operation ensuring the green indicator LED is illuminated • See below for operation of the self-test function • We recommend, on commissioning the installation, a minimum charge period of 24 hours before carrying out an emergency duration test SELF-TEST FUNCTION This product is programmed to carry out its own self-test operation according to the following programme:... - Page 7 WARNING This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed. GENERAL This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK) 2021 No.
-
Page 8: Warranty
WARRANTY This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free of charge replacement. - Page 9 230V IP65 50Hz °C SUPPLIED BY: (UK) MANUFACTURER (EU) AUTHORISED REPRESENTATIVE ML ACCESSORIES LTD, SLV LIGHTING GROUP, UNIT E CHILTERN PARK, DAIMLERSTRASSE 21-23, BOSCOMBE ROAD, DUNSTABLE 52531 ÜBACH-PALENBERG, GERMANY LU5 4LT, EMAIL: EPREL@GROUP.SLV.COM WWW.MLACCESSORIES.CO.UK AKDEC22_V1 MADE IN CHINA...
- Page 10 Manufacturers Declaration of Conformity For ML Accessories (Knightsbridge) Electrical products in accordance with UKCA marking ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in accordance with the requirements of the relevant legislation UKCA marking legislation UK SI 2016 No.
- Page 11 Manufacturers Declaration of Conformity For ML Accessories (Knightsbridge) Electrical products in accordance with CE marking ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in accordance with the requirements of the relevant legislation CE marking legislation...
- Page 12 230V 50Hz, IP20, Class 2, Non-Dim, Non-IC, house, Ta 0~45...
Need help?
Do you have a question about the TNXQUADMWSTW and is the answer not in the manual?
Questions and answers