Related Manuals for Knightsbridge TNXQUADMWEMW
Summary of Contents for Knightsbridge TNXQUADMWEMW
- Page 1 INSTALLATION & MAINTENANCE MANUAL TNXQUADMWEMW / TNXQUADMWEMBK TNXONEMWEMBK / TNXONEMWEMW...
-
Page 2: General Instructions
These instructions should be used to aid installation of the following products: TNXQUADMWEMW / TNXQUADMWEMBK / TNXONEMWEMBK / TNXONEMWEMW SAFETY • This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. - Page 3 • Provide power to the required point of installation (refer to BS7671 for correct cabling methods). INSTALLATION Suitable IP rated junction boxes should be used where required Remove the diffuser from the luminaire housing by unscrewing the four screws • Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the Drill the fixing holes in the rear of the fitting.
-
Page 4: Sensor Layout
Fig. 2 Fig. 2 • Attach the LED plate to the luminaire body by aligning the four butterfly screws on the body with the corresponding holes on the plate then turn clockwise to lock into place (see Fig. 3) • Attach the LED plate to the luminaire body by aligning the four butterfly screws on the body with the corresponding holes on the plate then turn clockwise to lock into place (see Fig. -
Page 5: Dip Switch Settings
DIP SWITCH SETTINGS Detection area Hold time 100% 1min 3min 5min 10min 20min Daylight sensor 30min * When set to disable, the daylight 2Lux sensor will switch the light 10Lux on when motion is detected 25Lux regardless of the ambient light level 50Lux Disable*... - Page 6 • Re-attach the diffuser to the luminaire body using the four screws • Switch on and check for correct operation ensuring the green indicator LED is illuminated – it will flash green if the battery is not connected, and is solid green to indicate that the battery is charging •...
-
Page 7: Warranty
dismantling instructions. This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where facilities exist The batteries in this luminaire are Lithium Ion and must be disposed of correctly. Please contact the local authorities for the disposal of this toxic waste. - Page 8 TESTING FOR EMERGENCY LUMINAIRES Recommended routine test procedure in accordance with BS5266: • Daily check – check LED charge indicator is illuminated • Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch or switching off circuit breaker.
- Page 9 230V IP65 50Hz °C SUPPLIED BY: (UK) MANUFACTURER (EU) AUTHORISED REPRESENTATIVE ML ACCESSORIES LTD, SLV LIGHTING GROUP, UNIT E CHILTERN PARK, DAIMLERSTRASSE 21-23, BOSCOMBE ROAD, DUNSTABLE 52531 ÜBACH-PALENBERG, GERMANY LU5 4LT, EMAIL: EPREL@GROUP.SLV.COM WWW.MLACCESSORIES.CO.UK DCFEB23_V1 MADE IN CHINA...
- Page 10 Manufacturers Declaration of Conformity For ML Accessories (Knightsbridge) Electrical products in accordance with UKCA marking ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in accordance with the requirements of the relevant legislation UKCA marking legislation UK SI 2016 No.
- Page 11 Manufacturers Declaration of Conformity For ML Accessories (Knightsbridge) Electrical products in accordance with CE marking ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in accordance with the requirements of the relevant legislation CE marking legislation...
- Page 12 230V 50Hz, IP20, Class 2, Non-Dim, Non-IC, house, Ta 0~45...
Need help?
Do you have a question about the TNXQUADMWEMW and is the answer not in the manual?
Questions and answers