TABLE OF CONTENTS INTRODUCTIONS TECHNICAL DATA GRAPHIC WARNINGS SAFETY RULES & PRECAUTIONS DESCRIPTIONS ASSEMBLY RULES FOR SAFE OPERATION CUTTING WITH A NYLON HEAD FUEL & OIL MIXTURE PREPARING FOR OPERATIONS STARTING ENGINE MAINTENANCE & CARE DISPOSAL AND RECYCLING WARRANTY TROUBLE SHOOTING...
Thank you for purchasing the Line Trimmer. This manual will explain the functions and use of the Line Trim-mer. Please read this manual carefully before operating the machine. TECHNICAL DATA MODEL LMCG260EH Remote type Automatic centrifugal clutch; flexible shaft Idle speed(r/min) 2800±200...
1. GRAPHIC WARNINGS • When working with the unit, all safety precautions must be taken. The line trimmer is a high-speed and fast cutting power tool. All safety precaution must be • Always wear safety goggles and dress observed to reduce the risk of personal injury. Please appropriately.
Page 5
• Keep hands and feet clear of the nylon cutting head • In start-up or during operation of the engine, do not while unit is in use. touch the hot parts of the unit such as the muffler, the high voltage wire or the spark plug. After the •...
3. DESCRIPTIONS Read the manual before operating the unit and keep the information for future reference to learn safe operating techniques. 1. NYLON HEAD 2.DRIVE SHAFT ASSEMBLY Contains a custom designed liner 9. FUEL TANK flexible drive shaft. Contains fuel and fuel filter. 3.D-HANDLE 10.
4. ASSEMBLY 5. RULES FOR SAFE OPERATION INSTALLING PLASTIC SHIELD WARNING Install the safety cover on the shaft with the safety cover bracket and the screws provided. Read the “Rules for Safe Operation “with care and follow the instructions in the manual to operate the Tighten the screws after setting the safety unit safely.
Do not wear ties, jewelry, or loose, dangling clothing WARNING which could be caught in the unit. Use only quality nylon monofilament line that is 2.4mm in diameter. Never use wire or wire reinforced line in place of nylon trimmer line. WARNING Use extreme caution when operating over bare spots and gravel.
Page 9
6.1 TRIMMING / MOWING powerful tool and can throw small stones and other objects a distance of 15 meters or more, causing Swing the trimmer from side to side in a scything injuries and damage to cars, houses and windows. motion.
7. FUEL & OIL MIXTURE 5. Continue to wind the line until you have 150mm of line left on each end. Note: It is helpful to clip and fasten the line on opposite ends of the spool to keep WARNING the line from unravelling during the next step.
8. PREPARING FOR OPERATIONS 8.1 STARTING ENGINE CAUTION IMPORTANT Do not pull the starter cord all the way out and do not Failure to follow proper fuel mix instructions may let go of the starter handle when the cord is cause damage to the engine.
Page 12
3. Rest the unit on a flat, firm area. Keep the cutting - The throttle lever will be held partly open until it is head off the ground and clear of surrounding objects, squeezed again. as it will start rotating upon engine starting. (1) Throttle lever 4.
Service Dealer. Improper adjustments may cause parts can be used for repairs and this must be engine damage and void warranty. carried out by an authorised LawnMaster Services Dealer to maintain warranty. FUEL FILTER • Fuel tank is fitted with a filter. The filter is situated...
12. TROUBLESHOOTING GUIDE CASE 1. STARTING FAILURE CHECK PROBABLE CAUSES ACTION Fuel Tank Incorrect Fuel Drain it and use correct fuel Fuel Filter Fuel Filter is clogged Clean Carburettor adjustment screw Out of normal range Adjust to normal range Sparking (no spark) Spark plug is fouled/wet Clean /dry Plug gap is incorrect...
Page 16
Steelfort 500 Rangitikei Street Private Bag 11045 Palmerston North, 4442, New Zealand 06 350 1350 | Steelfort.co.nz Steelfort Auckland 880 Great South Road, Penrose Auckland, 1061, New Zealand SCAN TO VIEW THE 09 573 1324 | outlet@steelfort.co.nz LAWNMASTER RANGE steelfortnz...