Related Manuals for LawnMaster LML261
Summary of Contents for LawnMaster LML261
- Page 1 26CC STRAIGHT SHAFT LINE TRIMMER SAFETY AND OPERATING MANUAL LMCG260EH PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING THE UNIT L261 PROUDLY A STEELFORT PRODUCT NZ OWNED...
-
Page 2: Table Of Contents
TABLE OF CONTENTS OPERATOR SAFETY GETTING STARTED Assembly FEATURES & TECHNICAL DATA OPERATION Fuel & Oil Mixture Rules for Operation Preparing for Operation STARTING THE TRIMMER Cold Start Warm Start Replacing Line MAINTENANCE & STORAGE... Maintenance Schedule Cleaning Engine General Inspection Spark Plug Air Filter Headline Replacement... -
Page 3: Operator Safety
DANGER Line Trimmer, the information container within this manual will help you to have many years of TOXIC FUMES safe and trouble free use of this LawnMaster • The exhaust of the engine contains carbon- product monoxide, an odorless, colorless poison gas. -
Page 4: Getting Started
• Keep all safety guards in place and in proper • Switch on the motor according to instructions working order at all times. and with feet well away from the cutter. • DO NOT allow any material to block the cooling •... - Page 5 d motor power ....0.7kw tor power ....0.7kw ower ....0.7kw Trimming line.
-
Page 6: Features & Technical Data
Fuel Tank Cap Handle Nylon Head Choke Lever Harness Hanger Spark Plug Shaft MODEL LML261 Idle speed (r/min) 3000 +/- 500 Nylon Head Twin Line Tap & Go Head Engine Air-Cooling, 2 Stroke Spark Plug NGK BPMR7A / BOSCH WSR6F Displacement (cc) 25.4... -
Page 7: Operation
ling with fuel FUEL IS EXPLOSIVE! Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs. FUEL IS EXPLOSIVE! Indicates danger, warning or caution. May be used in conjunction OPERATION STORING FUEL RISK OF DEVICE DAMAGE! with other symbols or pictographs. -
Page 8: Rules For Operation
3. PREPARING FOR OPERATION Immediately clean all traces of fuel which may have dripped on the machine or the ground and do not start the engine until the petrol fumes have dissipat- IMPORTANT Failure to follow proper fuel mix instructions may cause damage to the engine. -
Page 9: Replacing Line
7. If any problems occur during operation, release the throttle le ress the priming bulb 10 times. The machine will stop running. The machine will stop running. Move the choke lever to the START position. the choke lever to the START position. ove the choke lever to the START position. -
Page 10: Maintenance & Storage
Always clean and rewind the nylon spool at the end of the trimming season. Always clean the nylon spool or, if required, replace the spool. Always have the nylon spool cleaned or replaced by a qualified LawnMaster Service Dealer. Clip the housing back onto the line trimmer... -
Page 11: Spark Plug
k plug must be replaced by one with the same characteristics whenever the electrodes ned or the insulation has worn, or every 100 working hours. CLEANING THE ENGINE CLEANING THE ENGINE At the end of each working session, use a small brush To reduce the risk of fire or overheating, periodically clean the cylinder fins and air vents with To reduce the risk of fire or overheating, periodically clean the cylinder fins and air vents with compressed air and clear the silencer area to get rid of dust, branches, leaves or other debris. -
Page 12: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Fill the fuel tank with properly-mixed fuel The fuel tank is empty Press the primer bulb 10 times or until The priming bulb was not pressed fuel is visible enough Squeeze the throttle control and pull the The engine is flooded starter rope until the engine starts The engine will not... -
Page 13: Warranty
Only genuine spare parts can be used for repairs and this must be carried out by an authorised LawnMaster Service Dealer to maintain warranty. - Page 14 FIND US www.lawnmaster.co.nz lawnmasternz Steelfort Steelfort Auckland 500 Rangitikei Street, Private Bag 11045 880 Great South Road, Penrose Palmerston North, 4412, New Zealand Auckland, 1061, New Zealand 06 350 1350 09 573 1324...