Download Print this page
Kinderkraft XRIDER i-Size User Manual
Kinderkraft XRIDER i-Size User Manual

Kinderkraft XRIDER i-Size User Manual

Hide thumbs Also See for XRIDER i-Size:

Advertisement

Quick Links

XRIDER i-Size
USER GUIDE
MODEL: XRIDER i-Size
ECE R129.03 v.1.0
MODEL: I-GUARD
ECE.R129.03
ver. 1.2

Advertisement

loading

Summary of Contents for Kinderkraft XRIDER i-Size

  • Page 1 XRIDER i-Size USER GUIDE MODEL: XRIDER i-Size ECE R129.03 v.1.0 MODEL: I-GUARD ECE.R129.03 ver. 1.2...
  • Page 2 1.0 Usage CAUTION! The product graphics are for illustrative purposes only! The car seat has been designed, tested, and approved for use in accordance with the requirements of regulation No. 129 of the UNECE/ONU regarding the approval of child restraint systems (UN/ECE R129/03).
  • Page 3 Height of the child Seat orientation Seat attachment ISOFIX + support leg + internal harness 40cm–105cm straps ISOFIX + support leg + internal harness 76cm-105cm straps ISOFIX + support leg + internal harness 100cm-125cm straps...
  • Page 4: Safety Instructions

    2.0 Safety instructions Please take a few minutes to read this user manual to ensure appropriate child's safety. •DO NOT install the car seat on seats facing backward or sideways to the direction of travel. • The car seat may only be installed if the seat has 3- point safety belts.
  • Page 5 Information on the suitability of the car seat for use with a child seat can be • Never leave a child unattended in a child seat. found in the vehicle's operating instructions. • Make sure that luggage and other objects are adequately secured, •...
  • Page 6 • Do not use the seat if parts are damaged or loose. • On some car seats made of sensitive materials, the use of the car seat • In an emergency, it is important to release the harness quickly. This means can leave marks and/or cause discolouration.
  • Page 7: Side Impact Protection

    2.1 Side Impact Protection To provide additional protection in case of a side impact, the car seat is equipped with a bumper (side panel). The bumper should be positioned towards the car doors. Opening and closing the side panel: 1. Press the button located on the side panel - the side cover should automatically extend.
  • Page 8 3.0 Securing the child 3.1 Inserting the insole The additional insole should be used until the child reaches 76 cm. 1. Unfasten the safety harness 2. Spread the belts to the sides of the seat 3. Insert the insole Inner belts Belt buckle Headrest part of the insole Insole...
  • Page 9 3.2 Securing the child with the Inner harness straps 1. Press the harness adjustment button while pulling the harness straps. Remember! Do not pull on the shoulder pads. 2. Unclip the safety harness 3. Place the harness straps on the sides of the seat 4.
  • Page 10: Tightening The Harness

    3.3 Tightening the harness 1.Pull on the inner straps to eliminate looseness in the hip section, the harness should lie flat. 2.Press the harness with the adjustment strap until the harness lies flat on the child's body. IMPORTANT: Make sure the harness straps are not twisted. Ensure that the straps are tightened so that there is no more than 1cm of space between them and the child.
  • Page 11 Adjust the appropriate height of the shoulder straps so that the belt enters the car seat’s backrest flat, horizontally just above the child's shoulders.
  • Page 12 3.4 Height of the headrest The headrest should fit well around the child's head, the lower part of the headrest should be at shoulder height. 1.Loosen the harness straps all the way by pressing the button and pulling the harness straps Remember! Do not pull on the shoulder pads. 2.Grasp the headrest height adjustment lever, which is located at the back of the headrest, and pull gently upwards 3.
  • Page 13 3.5 Seat tilt adjustment mechanism 1.Pull the seat tilt adjustment lever 2.Adjust the seat tilt angle and release the lever in the required position (one of the four possible) 3.Gently move the seat until you hear a clear "click" sound A: Seat tilt adjustment lever...
  • Page 14 Caution! When the car seat is facing forward, you can use 4 positions for adjusting the backrest. However, when the car seat is facing backward, you can only use 1 position for adjustment.
  • Page 15 3.6 Rotation mechanism The rotation mechanism is a feature that helps to comfortably position the child or remove them from the car seat. 1.Pull one of the seat rotation levers located on the sides of the seat. 2.Rotate the car seat in the direction you choose. You will hear a "click" indicating that the car seat is locked in the selected position.
  • Page 16 IMPORTANT! For safety reasons, when the leg is not fully extended from the seat base, the car seat locks and there is no rotation.
  • Page 17 4.0 Mounting in the vehicle 4.1 ISOFIX mounting Before placing the car seat in the vehicle, unfold the support leg. 1.Place the car seat with the unfolded support leg on the car seat. Press both sides of the ISOFIX release button and extend the arms of the ISOFIX connectors to their maximum length.
  • Page 18 4.2 Assembly of the support leg 1.Pull the leg of the car seat out from the base and extend it fully. 2.Press the leg height adjustment buttons on both sides of the leg (this will release the leg extension lock, which will automatically extend). 3.Adjust the leg height so that the foot meets resistance from the floor.
  • Page 19 • CAUTION! Never mount the support leg on the storage compartment on the vehicle’s floor, this risks the storage compartment collapsing in an accident; if in doubt, check with the vehicle’s manual. • CAUTION! The support leg must never hang in the air and no objects may be placed under it.
  • Page 20 5.0 Hiding the 5-point safety harness 1.Loosen the safety harness completely by pressing the button and pulling the safety harness. Remember! Do not pull on the shoulder pads. 2.Remove the shoulder and buckle pads by unfastening the hoop&loop tapes. 3.Place the headrest in the highest position. 4.Unclip the buckle.
  • Page 21 7.Fasten the 5-point safety harness. 8.Open the storage compartment lid, then insert the fastened safety harness into it. 9.Lay the belts flat along the backrest and close the storage compartment lid. 10.Put the cover back on the car seat, using the snaps located on the edges of the material.
  • Page 22 6.0 Car seat assembly Caution! The seat should be placed directly on the vehicle seat. 6.1 Children with a height between 40 to 105 cm using the ISOFIX system with the support leg. 1.Extend the support leg. 2.Install the car seat on the seat using the ISOFIX connectors facing backward (if the car seat is already installed facing forward, rotate it using the rotation mechanism to face backward).
  • Page 23 5.Adjust the headrest to the child's height. 6.Seat the child in the car seat. 7.Secure the child with the internal safety belts. IMPORTANT: If the child has already reached 76 cm, pull out the inner insert before placing the child in the seat.
  • Page 24 6.2 Children with a height between 76 to 105 cm using the ISOFIX system with the support leg. 1.Extend the support leg. 2.Install the car seat on the seat forward facing using the ISOFIX connectors (if the car seat is already installed reverse facing rotate it using the rotation mechanism to face forwards.
  • Page 25 5.Adjust the headrest to the child's height. 6.Seat the child in the car seat. 7.Secure the child with the internal safety belts.
  • Page 26 6.3 Children with a height between 100 to 125 cm using the ISOFIX connectors and a vehicle’s 3-point safety belts. 1.Mount the car seat on the seat using the ISOFIX connectors facing forward. 2.Push the car seat as far as possible against the backrest of the seat and check for proper installation - the installation indicators should turn green.
  • Page 27 7.Thread the shoulder strap through the green shoulder strap guide. 8.Thread the car belt through both hip strap guides. Fasten the car belt. You will hear a characteristic "click." Shoulder strap guide Hibelt guide...
  • Page 28 6.4 Children with a height between 100 to 125 cm using vehicle’s 3-point safety belts. 1.Install the car seat on the seat facing forward. 2.Push the car seat as far as possible against the backrest of the seat. 3.Uncover the shell of the car seat by detaching the hoop&loop tapes located on its edges, and open the compartment for the belts located in the shell.
  • Page 29 7.Thread the shoulder strap through the green shoulder strap guide. 8.Thread the car belt through both hip strap guides. Fasten the car belt. You will hear a characteristic "click." Shoulder strap guide Hibelt guide...
  • Page 30 7.0 Disassembly of the car seat (ISOFIX installation system + support leg) 1.Fold the support leg extension by holding both buttons on the sides of the extension. Slide it upwards, tucking it into the remaining part of the leg. You will hear a "click," indicating that the leg has been stowed. 2.Press the release button located on both ISOFIX connectors.
  • Page 31: Cover Disassembly

    7.1 Cover disassembly 1.Remove the insole. 2.Loosen the safety belts completely by pressing the button and pulling the safety belts. Remember! Do not pull on the shoulder pads. 3.Adjust the headrest to the highest position. 4.Remove the shoulder and buckle pads. 5.Unfasten the hoop&loop tapes securing the cover to the front part of the backrest of the car seat.
  • Page 32: Cover Assembly

    7. Starting from the bottom of the car seat, carefully remove the cover 8. Gently pull the elastic band holding the fabric in place and slide it away from the hip belt guides 9. Slide the whole material over the top of the seat 7.2 Cover assembly To reinstall the cover simply reverse the above sequence of steps.
  • Page 33 • Do not use aggressive cleaning agents (such as solvents). • The harness can be cleaned with lukewarm water and soap. Warning! Metal fasteners should never be removed from the straps. The full Warranty Terms and Conditions are available on the website WWW.KINDERKRAFT.COM...