Advertisement
Quick Links
Advertisement
Related Manuals for Little Folks Furniture Classic Bunk Bed BBD010
Summary of Contents for Little Folks Furniture Classic Bunk Bed BBD010
- Page 1 Classic Bunk Bed Code: BBD010 PLEASE READ CAREFULLY & KEEP FOR FUTURE REFERENCE Axe230823...
-
Page 2: Product Safety
Thank you for buying a piece of furniture Treated properly it should be a faithful servant for years - and we hope you get the same amount of pleasure from it. Before you do please take a few minutes to read these instructions we suggest you carefully unpack everything, lay it out on a clean, flat floor and identify everything on the parts list in these instructions. - Page 3 Parts 1 x upper left mattress rail 2 x front safety rails (hole in rail) 1 x upper right mattress rail 1 x right ladder string (hole in rail) 2 x lower bed mattress rails 1 x left ladder string 3 x ladder treads 2 x long safety rails 2 x upper ends...
- Page 4 Fitting the mattress and safety rails 32 x small wooden dowels Insert 2 wooden dowels into each end of each rail. Gently tap dowels inwards until firmly in place. 1 x upper mattress rail (left) 1 x upper mattress rail (right) 2 x lower mattress rails 2 x long safety rails 2 x front safety rails...
- Page 5 Orientating the bunk bed. The small side hole on the mattress upper rails are used to fix the ladder to the bunk bed. You can have the ladder fitted on either the left or right side of the bunk bed (viewed facing the long side of the bed).
- Page 6 Building the UPPER bed frame (Two people) 8 x 9cm bolts and 8 x barrel nuts Front upper mattress rail (LADDER RIGHT) on the front of the bed, fitting the (ladder left) mattress rail along with the rear safety rails at the rear of the bed. Build the bed with the parts positioned as shown, Align the wooden dowels (fitted in rails)into the holes on the two upper bed ends.
- Page 7 Building the Lower bed frame (Two people) 4 x 9cm bolts and 4 x barrel nuts No ladder holes on this bed. Build the bed with the parts positioned as shown, Align the wooden dowels (fitted in rails) into the holes on the two lower bed ends. Insert a barrel nut into the hole at each end of the rails, allowing it to connect to a long bolt fitted from the outside, rotate to tighten the bed frame Align...
- Page 8 Fit the lower bed mattress base 34 x screws Carefully roll out the mattress base onto the mattress support pieces fitted on the inside of the mattress rails, webbing on the underside. Starting at one end of the bed, push the end lath tight up against the bed legs and screw in place using the two end holes in the lath.
- Page 9 Fit the upper bed mattress base 28 x screws Carefully roll out the mattress base onto the mattress support pieces fitted on the inside of the mattress rails, webbing on the underside. Starting at one end of the bed, push the end lath tight up against the bed legs and screw in place using the two end holes in the lath.
- Page 10 Make the bunk You need: 4 x large wooden dowels and 8 x 3.5cm screws. (TWO people to lift the upper bed onto the lower bed). Drop the 4 wooden dowel into each of the holes in the lower bed capping, pushing each dowel firmly down.
- Page 11 Assemble the ladder frame You need: 6 x 5cm screw bolts and 12 small wooden dowels insert 2 wooden dowel into each end of the three ladder treads, tapping each dowel down with a small hammer. Orientate the parts as shown. The ladder strings as “handed”left and right so take a moment to study the image, making sure that the tread holes are facing inwards.
- Page 12 Fix the ladder ( ladder right) 2 x 7cm bolts, 2 x 9cm bolts, 4 x barrel nuts, two sleeve nuts, 6 x 3.5cm screws & 1 x 3.5cm bolt Steps illustrated below. Lift the ladder onto the lower bed mattress rail, dropping the “notch” over the top edge.
- Page 13 Fit the ladder frame step explained below Once these bolts are ALL connected, tighten them to secure as well as tightening the upper mattress rail. Fix the front safety rails Slide the two safety rails into the wooden dowel holes located in the upper bed end.
- Page 14 Check the bed Now take a few minutes to look around the bed and tighten all the fittings as well as checking that the bed parts are firmly in place. Your bed is now assembled. Fit the mattresses.( two people) Carefully lift each mattress onto the sleeping surface.
-
Page 15: Product Safety
PRODUCT SAFETY The MAXIMUM thickness of the UPPER BUNK mattress is 20cm. The recommended size of the mattress is 190cm x 91cm (6`3” x 3`0) Periodically check that all assembly fixings are tightened properly, care should be taken to ensure that no fittings are loose. Always follow the manufacture`s instructions. - Page 16 Make two single beds (one lower end and one upper end) Two people required. Carefully remove the ladder, front and rear safety frames and mattress bases. Make two sets of single beds using one lower bed end and one upper bed end + two mattress rails and one mattress base.
- Page 17 300mm between the wall and the side of the bed. Additional or replacement parts should be obtained from Little Folks Furniture. Moving the bed Do Not drag or twist the bed.
- Page 18 Notes;...