Advertisement
Quick Links
Advertisement
Related Manuals for Little Folks Furniture Bowood BBD009
Summary of Contents for Little Folks Furniture Bowood BBD009
- Page 1 Bowood Bunk Bed Code: BBD009 PLEASE READ CAREFULLY & KEEP FOR FUTURE REFERENCE FOD121222...
-
Page 2: Product Safety
Thank you for buying a piece of furniture Treated properly it should be a faithful servant for years - and we hope you get the same amount of pleasure from it. Before you do please take a few minutes to read these instructions we suggest you carefully unpack everything, lay it out on a clean, flat floor and identify everything on the parts list in these instructions. - Page 3 Parts 1 x upper mattress rail left 1 x upper mattress rail right 2 x upper bed ends 1 x lower mattress rail left 1 x lower mattress rail right 1 x short ladder string 1 x long ladder string 2 x lower bed ends 3 x ladder treads Fittings...
- Page 4 Fitting the mattress rails 16 x wooden dowels Insert 2 wooden dowels at each end of each rail. Gently tap the dowels inwards until firmly in place (two outer holes as shown). There are four different rails so it is worth identifying these parts once the dowels are fitted.
- Page 5 Making the lower bed frame 4 x long Bolts 9cm, 4 x Barrel nuts ( two people) Select both large bed frames ( universal bed ends so can go either end of the bed)and one lower left hand mattress rail and one lower right hand mattress rail. Align the lower mattress rails with the dowels locating into the two bed leg holes, inserting the 9cm bolt centrally from the outside of the bed frame, engaging the barrel nut fitted from the inside.
- Page 6 Fit the lower bed mattress base 34 x screws Carefully roll out the mattress base onto the mattress support pieces fitted on the inside of the mattress rails, webbing on the underside.. Starting at one end of the bed, push the end lath tight up against the bed legs and screw in place using the two end holes in the lath.
- Page 7 Orientating the bunk bed. The small side holes on the mattress rails are used to fix the ladder to the bunk bed. You can have the ladder fitted on either the left or right side of the bunk bed (facing the long side of the bed). Simply rotate the bed frames to chose, holes on the left for the LEFT-HAND entrance or holes on the right for the RIGHT-HAND entrance, see images below.
- Page 8 Make the bunk You need: 4 x metal connecting pins and 8 x 3.5cm bolts (TWO people to lift the upper bed onto the lower bed). Drop the 4 connecting pins into each of the holes in the lower bed capping, orientating the pin so that it aligns with the intersecting bolt hole on the inside of the bed leg.
- Page 9 Fix the rear safety frame 6 x long bolts 6cm Lift the rear frame into position with the holes on the lower long rail downwards. Insert the rear frame (you might need to slightly loosen the rear mattress rail for access) and fit all 6 bolts, 2 at each end and 2 downwards.
- Page 10 Assemble the ladder frame (ladder LEFT) You need: 6 x 4.5cm bolts Orientate the parts as shown, long ladder string on the right and short ladder string on the left. Align each tread into the slots and connect each tread from the rear of the strings using two bolts.
- Page 11 Fit the ladder frame You need: 4 x 4cm bolts Orientate the ladder as shown and connect the ladder using the 4 bolts inserted from the inside of the bed. Once all four bolts are connected, rotate to tighten.
- Page 12 Fit the front safety frame You need: 2 x 4cm and 3 x 6cm bolts Orientate the front safety frame as shown and connect the frame using the 3 x 6cm bolts ( 2 in the right-hand bed leg and 1 downwards into the mattress rail) and 2 x 4cm bolts into the rear of the long ladder string.
-
Page 13: Product Safety Information
Product safety information The MAXIMUM thickness of the UPPER BUNK mattress is 23cm. The recommended size of the mattress is 190cm x 91cm (6`3” x 3`0) Periodically check that all assembly fixings are tightened properly, care should be taken to ensure that no fittings are loose. - Page 14 Make two single beds (one lower end and one upper end) Two people required. Carefully remove the ladder, remove the front and rear safety frame and mattress bases. Make two sets of single beds using one lower bed end and one upper bed frame + two mattress rails and one mattress base.
- Page 15 300mm between the wall and the side of the bed. Additional or replacement parts should be obtained from Little Folks Furniture. Moving the bed Do Not drag or twist the bed.