Download Print this page

Little Folks Furniture CBD001 Quick Start Manual

Frooti cabin bed

Advertisement

Quick Links

Frooti Cabin bed
Code: CBD001
PLEASE READ CAREFULLY & KEEP FOR FUTURE REFERENCE
Care of your Product
Welcome
Thank you for buying the Frooti Cabin bed
Before beginning assembly, please take a few minutes to read these instructions.
Lay the parts out on a clean, soft, flat surface (such as a carpeted floor) and compare with the
parts check list on the next page. Do not throw away any packaging until you are sure that you
have all the parts.
The product must be assembled by an adult. There are small parts so keep small children
away from the assembly area. Some stages of assembly require more than one person.
The recommended size of the mattress is 191cm x 90cm (6'3" x 3'0")
If, for any reason, you wish to return the product, you must disassemble the components and
use the original packaging.
Product Care
Clean your cabin bed by wiping with a damp cloth & drying with a soft cloth.
Never clean with abrasives, chemical cleaners or household polishes.
Take care when handling or moving the Bed. Careless handling can damage wooden furniture.
Try to lift rather than drag.
Product Safety
Periodically check all fittings to ensure that none have come loose.
l
Keep away from direct sources of heat, such as electric, gas or coal fires.
l
Do not allow children to Climb on the furniture.
l
Using this furniture other than for its intended purpose could cause damage
l
to the structure or serious injury to your child.
The Bed should not be used if any structural part is broken or missing.
l
Customer Service 01985 300588
If you can manage it, please try to persuade your children not to bounce on
l
the bed.
Warning: The child`s bed should not be placed too close to other furniture or
l
windows, blind cords, curtain pulls or other strings or cords, and should be
placed either tight to any wall or have a gap of 300mm between the wall and
the side of the bed.
Our Customer Service Number: 01985 300588
If you have a problem with this product, please call our Customer Service Team who will be
glad to help.
We can usually provide replacement and / or spare parts promptly; it will help us if you can
identify the specific part using the check list in the next section.
2

Advertisement

loading

Summary of Contents for Little Folks Furniture CBD001

  • Page 1 300mm between the wall and the side of the bed. Code: CBD001 Our Customer Service Number: 01985 300588 If you have a problem with this product, please call our Customer Service Team who will be glad to help.
  • Page 2: Parts Checklist

    Parts Check List Assembly 1. Preparing the carcass sides. You need: 12x Cam Pins and a Screwdriver. Side Rails x2 Place the Carcass Sides inside face up on a flat surface. Carcass Plinth x2 Carcass Back x2 Insert 3x Cam Pins into the smaller holes in each side as shown below. Repeat this assembly process for all four Carcass sides.
  • Page 3 3. Fit the Carcass Backs 6. Fit the Shelf. You need: 4x Shelf Studs. Stand each sub assembly upright, insert a Carcass Back into each assembly (painted side facing inwards), ensuring that each back correctly locates into the grooves on the Carcass Fit the 4x Shelf Studs into the holes on the outside faces of the two central Carcass sides, sides.
  • Page 4 9. Fit the Doors. 8. Attaching the Side Rails and End. You need: 4x Mounting Plates, 4x Hinges (complete with screws), 2x Rubber Buffers and a You need: 2x Bolts (35mm) and an Allen Key. Screwdriver. Fit the other End to the Carcass Side as before using the remaining 2x Bolts (35mm). Attach 4x mounting plates to the inside faces of the carcass sides using the pre- drilled pilot holes (See Attach the Side Rails to the Ends by fitting the pre-fitted Brackets over the Bolts (15mm) that Fig 9.1).
  • Page 5 11. Drawer assembly continued. 10. Assembling the drawer. You need: 4x Small Cam Pins, 4x Small Cams, 4x Screws for Drawer Carcass (35mm) and a You need: 7x Screws for Drawer Carcass (35mm) and a Screwdriver. Screwdriver. Ensure the Drawer frame is square and carefully fit the Draw Base. The lip on the Base Fit 4x Cam Pins into the Drawer Front.
  • Page 6 12. Attach the Castors. You need: 8x Small Screws for Castors (11mm), 4x Castors and a Screwdriver. Carefully turn the Drawer over and attach the 4x Castors to the Base with the 8x Screws (11mm) as shown below. Finally turn the Drawer over and carefully slide it into the bed Assembly.