Hide thumbs Also See for CRYOLYS Evolution:

Advertisement

Quick Links

CRYOLYS
Evolution
USER MANUAL
CRYOLYS Evolution
WWW.BERTIN-TECHNOLOGIES.COM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CRYOLYS Evolution and is the answer not in the manual?

Questions and answers

Summary of Contents for Bertin Technologies CRYOLYS Evolution

  • Page 1 CRYOLYS Evolution USER MANUAL CRYOLYS Evolution WWW.BERTIN-TECHNOLOGIES.COM...
  • Page 2: Table Of Contents

    Bertin Technologies product under the terms and conditions Decontamination protocol of the Restricted User License. Bertin Technologies is not liable for any use of this information when applied to other products. Bertin Technologies reserves the right to modify this document and make any changes at any time without prior notice.
  • Page 3: Bertin Technologies

    Instruments. wear protective gear for the eyes, face and skin. Store and handle dry ice in Bertin Technologies cannot be held liable for any damage or injuries a ventilated area. caused by using this device in a manner other than that described in this Ensure you are in possession of the safety data sheet manual.
  • Page 4: Warranty

    Alteration or removal of the label on which the device’s serial number is printed. 1.1.5 Special Safety Symbol Manufacturer: Bertin Technologies Parc d’activité du Pas du Lac 10bis Avenue Ampère 78180 MONTIGNY-LEBRETONNEUX FRANCE Comply with the safety instructions associated with this symbol.
  • Page 5: Description Of The Equipment

    USER MANUAL CRYOLYS Evolution ® Main seal: ensures a good seal between the cover and the 2.1. Description of the equipment module. Diffuser Plate: this is attached to the cover and directs air over the dry ice. Cooling module: ensures uniform diffusion of cooled air inside the Precellys®...
  • Page 6: Generating Cold Air

    USER MANUAL CRYOLYS Evolution ® 2.3. Generating cold air INSTALLING THE CRYOLYS® EVOLUTION Cold air is produced and maintained at the temperature set by the user. 3.1. Unpacking and installation It is important to check the delivered package carefully and inform your carrier of any damage.
  • Page 7 USER MANUAL CRYOLYS Evolution ® 4. Insert the hinge 5. Gently tighten the 2 6. Connect both fan and CAUTION - IMPORTANT reinforcement into screws supplied temperature sensor connectors to the hinge screw holes with the cover their respective connections at the Do not hold the Cryolys®...
  • Page 8: Packaging And Transport

    Packaging and transport versions are made available for the Precellys® Evolution Touch. This can Before transporting the device, you must: be done via the Bertin Technologies website (www.bertin-technologies. 1.Check that there is absolutely no dry ice inside the module com).
  • Page 9: Storage

    USER MANUAL CRYOLYS Evolution ® 3.3. Storage Note: for information about navigating the Precellys® Evolution from the screen interface, please refer to the Precellys® Evolution user manual The device must be stored in a dry location at a temperature between (23405-800-DU002-A).
  • Page 10 USER MANUAL CRYOLYS Evolution ® Manual Mode At the end of the cycle, open the Precellys® lid and retrieve the tubes and the tube holder Homogenization Insert new samples and close the Precellys® lid Pre-cooling Target temperature maintained protocol Note: Ensure that the volume of dry ice is sufficient. If no more homogenization is required, empty the cooling module.
  • Page 11: Cleaning And Decontamination

    USER MANUAL CRYOLYS Evolution ® CLEANING AND DECONTAMINATION SUPPORT AND DOCUMENTATION 5.1. Recommendations 6.1. Frequently asked questions The device must be stored in a dry location at a temperature between Before transporting the device, you must: +0°C and +50°C on a horizontal surface. 1.Check that there is absolutely no dry ice inside the module 2.Ensure there is no humidity or, if necessary, dry any humid areas Do not spray anything directly onto the device, particularly on...
  • Page 12: Troubleshooting

    Check that the dry ice covers at least Not enough dry ice the center of the reservoir. Bertin Technologies is responsible for treatment of WEEE for products sold in France (via RECYLUM). Message 1.Check that the fanconnector is For other countries, the importer is responsible for «Temp.
  • Page 13: Appendix: Example Of Ce Declaration

    USER MANUAL CRYOLYS Evolution ® APPENDIX: EXAMPLE OF CE DECLARATION APPENDIX: EXAMPLE OF CE DECLARATION Page Page...
  • Page 14 USER MANUAL CRYOLYS Evolution ® NOTES NOTES Page Page...
  • Page 15 Precellys 24 Touch Minilys Precellys Precellys Lysing Kits The Original The Individual Evolution Touch More than 1000 scientific protocols and data on the application center Join the Precellys community now! Bertin Technologies 10 bis, avenue Ampère, 78180 Montigny-le-Bretonneux, France www.bertin-technologies.com...

Table of Contents