Taylor C300NP Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Taylor Manuals
  4. Commercial Food Equipment
  5. C300 NP
  6. Operating instructions manual
Taylor C300NP Operating Instructions Manual

Taylor C300NP Operating Instructions Manual

Non-pressurized slush freezer
Hide thumbs Also See for C300NP:
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S 
MANUAL
Model C300NP
Non-Pressurized Slush Freezer
Original Operating Instructions
9/22//06 (Original Publication)
055072NP
(Updated 9/3/2020)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C300NP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Taylor C300NP

Summary of Contents for Taylor C300NP

  • Page 1 OPERATOR’S  MANUAL Model C300NP Non-Pressurized Slush Freezer Original Operating Instructions 9/22//06 (Original Publication) 055072NP (Updated 9/3/2020)
  • Page 2 Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be the original set of instructions. © 2006 Taylor Company 055072NP Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be...

  • Page 3: Table Of Contents

    Table of Contents Section 1: To the Installer Installer Safety ............1-1 Site Preparation .
  • Page 4 Table of Contents Section 6: Operating Procedures Assembly ............6-1 Sanitizing .

  • Page 5: Section 1: To The Installer

    Taylor distributor. poor performance or damage to the machine. This machine is made using USA sizes of hardware. All Note: All repairs must be performed by a Taylor metric conversions are approximate and vary in size. service technician. To the Installer...

  • Page 6: Air-Cooled Machines

    3/8 in. (9.5 mm) inside diameter water lines. A flexible line is recommended, if local codes permit. A minimum of 25 psi. (172 kPa) water pressure is required to avoid having the machine cut out the low To the Installer Model C300NP...

  • Page 7: Electrical Connections

    Failure to do so can result in severe personal injury from electrical shock. Failure to follow these instructions may result in electrocution. Contact your local authorized Taylor distributor for service. WARNING! Avoid injury. • DO NOT operate the machine unless it is properly grounded.

  • Page 8: Beater Rotation

    For information regarding applicable local laws, It is recommended that beater rotation adjustment be please contact your local authorized Taylor distributor. performed by a Taylor service technician. Refrigerant IMPORTANT! Refrigerants and their associated lubricants may be extremely moisture absorbent.

  • Page 9: Section 2: To The Operator

    In the event you should require technical assistance, please contact your local authorized Taylor distributor. Note: Your Taylor warranty is valid only if the parts are authorized Taylor parts, purchased from the local authorized Taylor distributor, and only if all required service work is provided by an authorized Taylor service technician.

  • Page 10: Compressor Warranty Disclaimer

    It should also be noted that Taylor does not warrant the refrigerant used in its equipment. For example, if the refrigerant is lost during the course of ordinary service...

  • Page 11: Section 3: Safety

    (including, but not limited to, freezer door, freezer and its parts. Taylor has gone to extreme efforts to beater, or scraper blades), unless all control design and manufacture built-in safety features to protect switches are in the OFF position.
  • Page 12 Failure to follow these instructions may result in The authorized installer should inspect the machine for electrocution. Contact your local authorized Taylor damage and promptly report any damage to the local distributor for service.
  • Page 13 Noise Level: Airborne noise emission does not exceed 78 dB(A) when measured at a distance of 39 in. (1.0 m) from the surface of the machine and at a height of 62 in. (1.6 m) from the floor. Safety Model C300NP...
  • Page 14 SAFETY Notes: Safety Model C300NP...

  • Page 15: Exploded View

    Exploded View Figure 4-1 Item Description Part No. Item Description Part No. 054676 054670 Panel-Side-Left Panel-Front-Lower 054672 057938 Panel-Rear Shelf-Drip Tray 054671 057738 Panel-Side-Right Tray-Drip 054683-27 057939 Display-Lighted Shield-Splash 069142 078418 Panel-Front-Upper Switch-Rocker-OFF-ON 054668 Panel-Front-Shell Operator Parts Identification Model C300NP...

  • Page 16: Beater Door Assembly

    Valve-Draw Self Close 080662 O-ring-7/8 OD X .139w 025307 O-ring-1in.OD X.139w 032504 Seal-Drive Shaft 032560 Handle A.-Draw-Slushblack X47384 Arm-Baffle 047729 Plug-Prime*STNLS 050405 Baffle A. X47731 O-ring-.563 OD X .070w-#013 043758 Nut-Stud 043666 Door A.-Slush-Partial Self Close X83472SSP Operator Parts Identification Model C300NP...

  • Page 17: Accessories

    OPERATOR PARTS IDENTIFICATION Accessories Apply the appropriate Taylor approved food safe lubricant. Figure 4-3 Item Description Part No. Item Description Part No. 014753 013163 Brush-Draw Valve 1-1/2”OD Pail-10 Qt. X56829 023316 Kit A.-Tune Up Brush-Mix Pump Body-3”x7” 048232 013072 Lubricant-Taylor Hi Perf...
  • Page 18 OPERATOR PARTS IDENTIFICATION Notes: Operator Parts Identification Model C300NP...

  • Page 19: Section 5: User Interface

    Item To better communicate in the international arena, Product Light—Left Side symbols have replaced words on many of our operator switches, function, and fault indicators. Your Taylor Control Switch machine is designed with these international symbols. Keypad—Left Side The following chart identifies the symbol definitions.

  • Page 20: Control Switch

    The Current Conditions Note: Syrup, CO and water are satisfied. screen will be displayed until manually changed. Pressing the AUTO (- ->) keys on both sides of the machine will display this screen. AUTO MODE AUTO SYRUP User Interface Model C300NP...

  • Page 21: Finding Current Fault Conditions

    BEATER OVERLOAD—Beater motor is out on overload. When this fault occurs, the machine automatically turns off. The fault clears when the condition is corrected. FAULT DESCRIPTION L: NO FAULT FOUND R: SYRUP PRESS LOW + + + User Interface Model C300NP...
  • Page 22 If the product exceeds 120°F Sunday in April, and will be retarded by 1 hour at 2:00 (49°C) for any reason (in any mode of operation), the a.m. on the last Sunday in October. entire machine shuts down. User Interface Model C300NP...
  • Page 23 The first feature indicates the software version. CYCLE 1 09:00 + + + - - - SYSTEM INFORMATION C300 CONTROL UVC2 VERSION 1.03 DEFROST TIME LEFT CYCLE 1 09:00 <- - - -> + + + - - - User Interface Model C300NP...
  • Page 24 Page numbers are located in the upper right-hand corner Repeat for the right side of the machine. of the display. The most recently recorded fault will appear on page 1. The fault description is listed on the User Interface Model C300NP...

  • Page 25: Syrup Out Indicator

    This will continue until the CO is replaced. If the and spouts. is not replaced within 1 minute, the machine will shut down and a fault message will appear. User Interface Model C300NP...
  • Page 26 USER INTERFACE Notes: User Interface Model C300NP...

  • Page 27: Section 6: Operating Procedures

    Operating Procedures Section 6 The Model C300NP contains two 7 qt. (6.6 L) freezing 11118 cylinders. The syrup flow control combines the two ingredients of water and syrup and sends this combination to the Apply the appropriate freezing cylinder. As product is drawn, new product will Taylor approved food safe lubricant.
  • Page 28 11548 11120 Apply the appropriate Taylor approved food safe lubricant. Figure 6-4 Figure 6-6 5. Holding the blades in position, insert the beater 7. Insert the short end of the baffle assembly into the assembly into the freezing cylinder and slide it into pilot hole in the center of the driveshaft.
  • Page 29 Insert the draw valve handle through the slot and into the draw valve hole. Apply the appropriate Taylor approved food safe lubricant. 101605 Figure 6-7 10. Turn the door upside down. Insert the draw valve spring.
  • Page 30 18. Place the O-ring onto the prime plug and lubricate. handle. Install it on the other side, through the longer slot and into the draw valve hole. 11145 Apply the appropriate Taylor approved food safe lubricant. Figure 6-16 Operating Procedures Model C300NP...
  • Page 31 21. Slide the white, plastic front bearing onto the bearing hub, making sure that the flanged end of the bearing is resting against the freezer door. Do not lubricate the door gasket or front bearing. Figure 6-20 Operating Procedures Model C300NP...

  • Page 32: Sanitizing

    17013 Figure 6-22 2. Prepare 2 gal. (7.6 L) of an approved 100 ppm ® or  sanitizing solution (examples: Stera-Sheen ® Kay-5 ). Use warm water and follow the manufacturer's specifications. Figure 6-25 Operating Procedures Model C300NP...
  • Page 33 13. Disconnect the syrup connectors in the sanitizing solution until the solution purges out of the vent at the solution. top of the mix tank and begins draining into the front drip tray. Press the OFF (<- -) key. Operating Procedures Model C300NP...

  • Page 34: Priming/Brixing

    The is flowing. refrigeration system would have to run longer to freeze this excess syrup. A reading lower than this could cause a freeze-up in the freezing cylinder because of the excess water. Operating Procedures Model C300NP...
  • Page 35 11. Once the proper brix has been achieved, turn the press the AUTO (- ->) key on both sides. When the handle up to allow product to flow to the mix tank. machine cycles off, the product will be at serving  viscosity. Operating Procedures Model C300NP...

  • Page 36: 120 Day Closing Procedure

    A B C D E F G H I RINSE / SANITIZE < > - Press the MENU (SEL) key. Move the cursor under “RINSE” by pressing the OFF (<- -) key twice. 6-10 Operating Procedures Model C300NP...

  • Page 37: Cleaning

    Press the OFF (<- -) key and close the by pressing the AUTO (- ->) key until the third line draw valves. indicates RINSE / SANITIZE. Press the MENU (SEL) key. Move the cursor under the word SANITIZE. 6-11 Operating Procedures Model C300NP...

  • Page 38: Disassembly

    10. Thoroughly brush-clean all disassembled parts in the cleaning solution, making sure all lubricant and syrup is removed. Place all the cleaned parts on a clean, dry surface to air-dry. 11. Wipe clean all the exterior surfaces of the machine. Figure 6-39 6-12 Operating Procedures Model C300NP...
  • Page 39 OPERATING PROCEDURES Notes: 6-13 Operating Procedures Model C300NP...
  • Page 40 OPERATING PROCEDURES 6-14 Operating Procedures Model C300NP...

  • Page 41: Section 7: Operator Checklist

    Disconnect the freezer from the main power source to the rear shell bearing located at the rear of the prevent possible electrical damage. freezing cylinder. Use a generous amount of Your local Taylor distributor can perform this service for cleaning solution on the brush. you. ...
  • Page 42 OPERATOR CHECKLIST Notes: Operator Checklist Model C300NP...

  • Page 43: Section 8: Troubleshooting Guide

    Lubrication of hex end of b. Do not lubricate the hex end. If the rear shell driveshaft. necessary, contact a service bearing. technician for removal. Troubleshooting Guide Model C300NP...
  • Page 44 O-rings. leakage from door spout. b. Wrong type lubricant on draw b. Use food-grade lubricant valve O-rings. (example: Taylor Lube HP). c. Worn or missing draw valve  c. Replace or install O-rings on 6-3 / 9-1 O-rings. draw valve.

  • Page 45: Section 9: Parts Replacement Schedule

    Black Bristle Brush, 1” x 2” Inspect and replace if necessary. Minimum Double-Ended Brush Inspect and replace if necessary. Minimum Brush, 1-1/2” x 2” Inspect and replace if necessary. Minimum Brush, 3” x 7” Inspect and replace if necessary. Minimum Parts Replacement Schedule Model C300NP...
  • Page 46 PARTS REPLACEMENT SCHEDULE Notes: Parts Replacement Schedule Model C300NP...

  • Page 47: Section 10: Limited Warranty On Equipment

    LIMITED WARRANTY Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or remanufactured part, at Taylor’s option, to replace the failed defective part at no charge for the part.
  • Page 48 LEGAL REMEDIES The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.

  • Page 49: Section 11: Limited Warranty On Parts

    Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or remanufactured Part, at Taylor’s option, to replace the failed defective Part at no charge for the Part.
  • Page 50 Taylor. 5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any release sheets and clips for the Product’s upper platen assembly.
  • Page 51 LEGAL REMEDIES The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
  • Page 52 LIMITED WARRANTY ON PARTS Notes: 11-4 Limited Warranty on Parts Model C300NP...

Table of Contents