Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Keysight ENA Series
Summary of Contents for Keysight ENA Series
- Page 1 E5080B ENA Series RF Network Analyzers INSTALLATION GUIDE...
- Page 2 EULA. governed by United States and Declaration of Conformity Keysight shall be under no obligation international copyright laws. to update, revise or otherwise modify Trademark Acknowledgments Declarations of Conformity for this the Software.
-
Page 3: Caution
When you notice any of the unusual conditions listed below, immediately terminate operation and disconnect the power cable. Contact your local Keysight Technologies sales representative or authorized service company for repair of the instrument. If you continue to operate without repairing the instrument, there is a potential fire or shock hazard to the operator. -
Page 4: Manufacturer's Declaration
European Directives, and carries the CE marking accordingly: • The Low Voltage Directive 2014/35/EU • The EMC Directive 2014/30/EU To obtain Declaration of Conformity, please contact your local Keysight Technologies sales office, agent or distributor. Keysight E5080B ENA Series RF Network Analyzers... -
Page 5: Safety Notice Supplement
• This equipment is tested in stand-alone condition and in combination with the accessories supplied by Keysight Technologies against the requirement of the standards described in the Declaration of Conformity. If it is used as a system component, compliance of related regulations and safety requirements are to be confirmed by the builder of the system. -
Page 6: General Safety Precautions
To avoid the danger of introducing additional hazards, do not install substitute parts or perform unauthorized modifications to the instrument. Return the instrument to a Keysight Technologies Sales and Service Office for service and repair to ensure that safety features are maintained in operational condition. -
Page 7: Safety Symbols
Certification Keysight Technologies certifies that this product met its published specifications at the time of shipment from the factory. Keysight Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology, to the extent allowed by the Institution’s calibration facility or by the calibration facilities of other... -
Page 8: Documentation Warranty
Keysight shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or any information contained herein. -
Page 9: Manuals For E5080B
Caution Manuals for E5080B Manuals for E5080B Keysight provides the following three manuals for E5080B. The latest version of all documentations can be downloaded from http://www.keysight.com/manual/e5080b. Installation Guide The installation guide (this manual) provides start up setup information when you use the E5080B for the first time and troubleshooting information when the Windows cannot be boot up. - Page 10 Caution Manuals for E5080B Keysight E5080B ENA Series RF Network Analyzers...
-
Page 11: Table Of Contents
System Recovery ............24 Keysight E5080B Installation Guide... - Page 12 Procedure to execute the factory recovery ........25 Keysight E5080B Installation Guide...
-
Page 13: Installation
Step 3. By referring to the furnished contents list, check that all packaged items supplied with the analyzer have been received as per the specified options. Step 4. After checking, if one of the following applies, contact your nearest Keysight Technologies sales and service office. -
Page 14: Environmental Requirements
4. A fault has been detected in the subsequent operation check of the analyzer. If an abnormality is detected in step 1, contact the company that transported the analyzer as well as your nearest Keysight Technologies sales and service office. Environmental Requirements Set up the E5080B where the following environmental requirements are met. -
Page 15: Protection Against Electrostatic Discharge (Esd)
AC outlet or the E5080B unit. When installing the E5080B, ensure that there is sufficient free space around the unit to permit quick disconnection of the plug (from AC outlet or E5080B unit) in case of emergency. Keysight E5080B ENA Series RF Network Analyzers... -
Page 16: Power Supply
Use the supplied power cable with grounding wire to securely ground the E5080B. For power cord list and options, refer to www.keysight.com/find/powercords. Keysight E5080B ENA Series RF Network Analyzers... -
Page 17: Blown Fuses
Blown Fuses If the fuse appears to have blown during operation, this instrument may be subject to failure and must be repaired. For any assistance, contact Keysight Technologies Customer contact center listed at the end of this guide. The E5080B uses the following fuse types: UL/CSA Type, Slow-Blo, 8 A-250 Vac. -
Page 18: Installing Rack Mount
Steps to install the rack mount: 1. Install tray on the rails. Fasten front screws. 2. Remove bottom feet of the instrument. 3. Attach front flanges and set the instrument on tray. Then fasten front screws. Keysight E5080B ENA Series RF Network Analyzers... -
Page 19: Starting The E5080B
"safe mode." If this occurs, first shut down the system to set it to the standby state and then turn ON the power supply again to start up the system in normal mode. Keysight E5080B ENA Series RF Network Analyzers... -
Page 20: Disconnection From Supply Source
“Ensuring Adequate Free Space around Analyzer for Immediate Disconnection of Power Cable in Case of Emergency” on page When turning the power OFF under normal circumstances, always follow the methods described in “Turning the Power OFF” on page Keysight E5080B ENA Series RF Network Analyzers... -
Page 21: Initial Registration Of E5080B
When the Windows agreement message box appears, click Agree. The rest of the procedure runs automatically. The Touch Screen does not require any calibration and it works from the very first time you use the E5080B. Keysight E5080B ENA Series RF Network Analyzers... - Page 22 Installation Initial Registration of E5080B Keysight E5080B ENA Series RF Network Analyzers...
-
Page 23: Troubleshooting
Keysight E5080B ENA Series RF Network Analyzers Installation Guide 2 Troubleshooting This chapter describes the troubleshooting during start up and the procedure of the operating system (OS) recovery when the Windows OS has been damaged. Troubleshooting during Startup Table 2-1. System When you encounter the problem during start up, see recovery saves most of problems. -
Page 24: System Recovery
1. The default setting of the storage is recovered during the system recovery. For the storage that had failed earlier and had been replaced (after purchase), its default setting may not be the same as the factory state. Keysight E5080B ENA Series RF Network Analyzers... - Page 25 Step 5. When the screen as shown in the figure below appears, select Instrument Image Recovery System and press [Enter]. Figure 2-1 Instrument Image Recovery System Selection Screen After several seconds, the next screen appears automatically even if you do not press any key. Keysight E5080B ENA Series RF Network Analyzers...
- Page 26 Step 6. Software End User License Agreement appears. Press [Agree]. Figure 2-2 Software End User License Agreement Step 7. Type 2 to select Recover the original factory system image option and press [Enter]. Figure 2-3 System recovery selection screen Keysight E5080B ENA Series RF Network Analyzers...
- Page 27 Step 12. After the restart, execute initial registration. For information on the execution procedure, refer to “Initial Registration of E5080B” on page 21 Never turn OFF the power during the system recovery because doing so may cause serious damage to the E5080B. Keysight E5080B ENA Series RF Network Analyzers...
- Page 28 Troubleshooting System Recovery Keysight E5080B ENA Series RF Network Analyzers...
- Page 29 Exclusive Remedies Inspection checking the shipment power check the power supply disconnection from supply source power cable options verification and connection of power cable safety symbols shutdown turning the power OFF System Recovery How to Execute Keysight E5080B Installation Guide...
- Page 30 Index Keysight E5080B Installation Guide...
- Page 31 This information is subject to change without notice. © Keysight Technologies 2019-2022 Edition 2, May 2022 *E5080-90010* E5080-90010 www.keysight.com...
Need help?
Do you have a question about the ENA Series and is the answer not in the manual?
Questions and answers