1. Manuals
  2. Brands
  3. ViewEra Manuals
  4. Monitor
  5. V191 Series
  6. User manual

ViewEra V191 Series User Manual

19" tft-lcd monitor
Hide thumbs Also See for V191 Series:
Table of Contents

Advertisement

Quick Links

19" TFT-LCD MONITOR
V191 Series
USER' S MANUAL
www.viewera.com
Rev 1.1
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V191 Series and is the answer not in the manual?

Questions and answers

Related Manuals for ViewEra V191 Series

Summary of Contents for ViewEra V191 Series

  • Page 1 19” TFT-LCD MONITOR V191 Series USER’ S MANUAL www.viewera.com Rev 1.1...

  • Page 2: Table Of Contents

    CONTENTS 1. Introduction Product Description ... Page 3 Package Contents ... Page 3 Product Features …... Screen Cleaning Techniques ... Additional ... 2. Control Functions Function Selection ... Page 7 Function Adjustments... Page 8 3. Installation ... Page 9 4. Display Modes... Page 10 5.

  • Page 3: Introduction

    1. Introduction Product Description Congratulations on your purchase of the ViewEra V191 series LCD monitor. It incorporates high quality display into a small light-weighted module. It has power-saving capabilities and emits no radiation. You will certainly benefit from this monitor in lots of ways; to name some of them: comfort, safety, space-saving and environmental protection.

  • Page 4: Screen Cleaning Techniques

    2. Power  Use the type of power indicated on label. 3. Plugs  Do not remove any of the prongs of the monitor’ s three-pronged power plug.  Disconnect the power plug from the AC outlet under following conditions：...
  • Page 5  If the power supply cord, which came with your monitor, is to be connected to the PC instead of the wall outlet, Use an UL/TUV approved computers with receptacle rated 100~240V AC, 50/60Hz, 1.0A (minimum) only.

  • Page 6: Control Functions

    2. Control Functions The monitor digital control functions are located on the front panel. They are shown in the figure below and described in the following paragraphs. 1. Power switch with Indicator LED 2. Function Keys Function Selection 1. Press the “ 1” knob to show the OSD menu. Then use the “ ” and “ ”...
  • Page 7 switch the image signal by connecting both VGA and DVI cables. If you want to switch VGA to DVI image signal, you need to turn off your PC and disconnect the VGA cable. Then connect the DVI cable and turn on your PC. 2.
  • Page 8 5.Image Auto Tune - Adjust geometry of the image automatically. H. Width - Adjust the horizontal sync size of signal. H. Phase - Adjust the horizontal sync phase of signal. H. Position - Adjust the horizontal position of the image. V.

  • Page 9: Installation

    1. Before you connect the cables, made sure that the monitor and the system unit power switches are off. 2. Plug one end of the 15 pin-signal cable or DVI cable to the monitor and the other end to the video signal connector at the rear of the system. Tighten the two screws on the cable connector.

  • Page 10: Display Modes

    Micro-controller Features The micro-controller automatically detects the video board installed in your system. When you turn on the monitor, the micro-controller checks the display mode memory stored in the user setting area of the video board, and then the factory presetting area. It then adjusts to the proper display mode.

  • Page 11: Signal Connector Pin-Outs

    MODE Resolution (Dots*lines) 640×350 720×400 640×480 VESA/75 640×480 VESA/60 800×600 VESA/75 800×600 VESA/60 1024×768 VESA/70 1024×768 VESA/75 1024×768 VESA/60 1280×1024 5. Signal Connector Pin-outs To connect VGA, 8514A or IBM-compatible graphics adapters, use a 15 pin mini D-type male connector. 15-pin Mini D-type Male Connector Pin Assignment 1 Red Video...

  • Page 12: Power Saving Features

    Normal Stand-by Suspend The monitor uses the H. Sync and V. Sync signals to determine the operation mode to enter. The monitor power-saving feature automatically turns off H. Sync and V. Sync if there is no input from the system for a certain period of time. To use this feature,...

  • Page 13: Product Specifications

    7. Product Specifications Model Features Panel Type: Anti-glare, active TFT-LCD Size: 19” diagonal Pixel Pitch: 0.294 (W) ×0.294 (H) mm Brightness: 300 cd/㎡ (typical) Contrast Ratio: 700:1 (typical) Response Time: 25 ms (typical) Viewing Angle(H / V) 160° / 160° Max.

  • Page 14: Dead Pixel Policy

    5 pixels. 9. Warranty & Customer Service Warranty ViewEra warrants the V191D TFT-LCD monitor for three years for parts and labor, one year for LCD panel from the date of purchase. For detail warranty information, please http://www.viewera.com/warranty.htm...

  • Page 15: Windows Setup

    For the best view, please set the monitor type in Windows. Please select as following: Control Panel > Monitor > Setting > Advance > Monitor > Change > Show all List …> Stand > For 1280 ×1024, please set to “ SXGA 1280 × 1024@75Hz”...

  • Page 16: Trouble Shooting

    → Make sure you are using the standard power adapter coming with the monitor. → Check your video card if the driver is correctly installed. If there is no video...
  • Page 17 3) The text and icon look blurry → LCD monitor has a native resolution which pixels are produced by cells in fixed positions. When a resolution different from the native resolution is chosen, the LCD monitor uses various interpolation methods to achieve the pseudo resolution.

This manual is also suitable for:

V191d

Table of Contents