Pioneer VSX-D2S Operating Instructions Manual page 28

REAR PANEL FACILITIES
Orr
S (connector) video jacks
When used in conjunction with a VCR, Video disc player (LD player)
or TV monitor equipped with S video jacks, connect to these jacks.
(See page 8)
© CENTER AMP jacks
[PRE-OUT]
When a separate power amplifier is used to drive the surround
center speaker, connect the power amplifier to this jack.
{POWER IN]
When a separate preamplifier is used for a center speaker and this
unit is used as a power amplifier, connect the preamplifier to this
jack.
@ SUB WOOFER OUT jack
If you want to boost the low frequencies, or want to use the unitina
3D system, connect to a sub woofer power amplifier.
@ REAR AMP jacks
(PRE OUT]
Whena separate power amplifier is used to drive the rear speakers,
connect the power amplifier to these jacks.
(POWER IN]
Whena separate preamplifier is used for rear speakers and this unit
is used as a power amplifier, connect the preamplifier to these jacks.
@ CENTER SPEAKER terminals
Connecting the surround center channel speaker system(s).
You can connect two speakers for dual center, so you can locate
speakers on both sides of the TV.
Speaker impedance:
Refer to @ SPEAKER IMPEDANCE SELECTOR switch.
NOTE:
Do not allow any of the cord's conductors to protrude from the
terrninals or touch any other conductors. Malfunctioning or
breakdowns may occur when conductors come into contact with
each other.
@ FRONT SPEAKERS terminals
A: Connect to the first set of speakers.
B: Connect to a second set of speakers.
Speaker impedance:
Refer to @ SPEAKER IMPEDANCE SELECTOR switch.
NOTE:
Do not allow any of the cord's conductors to protrude from the
terrninals or touch any other conductors. Malfunctioning or
breakdowns may occur when conductors come into contact with
each other.
@ REAR SPEAKERS terminals
Cornect the rear speakers to these terminals.
Speaker impedance
Connect speaker systems with a nominal impedance of between 8
and 16 Q. :
NOTE:
Do not allow any of the cord's conductors to protrude from the
terrninals or touch any other conductors. Malfunctioning or
breakdowns may occur when conductors come into contact with
each other.
@ MULTI-ROOM SPEAKERS terminals
Comnect to the Multi-room speakers.
Speaker impedance
Connect speaker systems with a nominal impedance of between 8
and 16 Q.
28
<ARB1455>
NOTE:
@ CD IN jacks
Connect to compact disc player.
@ PHONO IN jacks
Connect to turntable.
@ GND terminal
Connect the turntable ground lead to this terminal.
® LD jacks (input)
[VIDEO IN] .
When watching the video image from an LD player or a VCR used for
playback, connect its VIDEO OUTPUT jack here.
[AUDIO IN (L,R)}
player) or a VCR for playback, connect its AUDIO OUTPUT jacks
here.
@ TV/SAT jacks (input)
Use these jacks if you wish to connect a TV tuner with both video and
audio outputs.
[VIDEO IN]
Connect the TV tuner's VIDEO OUTPUT to this jack.
[AUDIO IN (L, R)]
Connect the TV tuner's AUDIO OUTPUT to these jacks.
@ FRONT AMP jacks
[PRE-OUT]
When a separate power amplifier is used to drive the front speakers,
connect the power amplifier to these jacks.
[POWER IN]
When a separate preamplifier is connected and this unitis used as a
power amplifier, connect the preamplifier to these jacks.
@ CONTROL IN, OUT jacks
mark.
IN : For connection from the CONTROL OUT jack tf another
component (TV, etc.)._
OUT : For connection to the CONTROL IN jack o another
component.
NOTE:
The receiver's remote sensor does not function when a plug is
inserted in the IN jack. To operate, point the remote controursitat the
remote sensor on the component to which the receiver' IN jack is
connected.
When using
the MR-100
multi-room system =
remote control
sensor unit. @ (ia
a
MR-100 Conran ;
Aco Receiver f—\
Pioneer component
bearing the
mark. To th CCONTROL IN
Remote jack ¢ eche Pioneer
control COMip--zENt bearing the
unit nar k.
Remote control unit