Related Manuals for SMC Networks ASD F-A Series
Summary of Contents for SMC Networks ASD F-A Series
- Page 1 Doc.no.DOC1063304 PRODUCT NAME Dual Speed Controller with One-touch Fitting Push-lock Type MODEL / Series / Product Number ASD＊＊＊F-＊＊-＊＊A...
-
Page 2: Table Of Contents
Contents 1．Safety Instructions 2 ～ 3 2．Specific Product Precautions 4 ～ 9 3．Application 4．Specifications 5．Malfunctions and Countermeasures 6．Adjusting the speed 7.Construction... -
Page 3: 1．Safety Instructions 2
Dual Speed Controller with One-touch Fitting Push-lock Type/ASD-A Series Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) , and other safety regulations. - Page 4 Dual Speed Controller with One-touch Fitting Push-lock Type/ASD-A Series Safety Instructions Caution We develop, design, and manufacture our products to be used for automatic control equipment, and provide them for peaceful use in manufacturing business. Use in non-manufacturing business is not covered. Products we manufacture and sell cannot be used for the purpose of transactions or certification specified in the Measurement Act.
-
Page 5: 2．Specific Product Precautions 4
Mounting 2. Specific Product Precautions Warning Design/ Selection (1) Operation Manual Install the products and operate it only after Warning reading the operation Manual carefully and understanding its contents. Also, keep the (1) Confirm the specifications. Manual where it can be referred to as This product is designed to be used only in a necessary. - Page 6 Mounting Mounting Warning Warning (7)Do not use tools such as pliers to rotate the (15)Do not use Body A and/or elbow body for knob. applications involving continuous rotation. It can cause idle rotation of the knob or Body A and the fitting section may be damage.
- Page 7 Mounting Piping Threads with Sealant Caution Caution (1)-2 For R, NPT, G thread (3) Reuse ①Tightening method ① Normally, fittings with a sealant can be When installing the connection thread, tighten it reused 2 to 3 times. to the appropriate tightening torque as shown in ②...
- Page 8 Mounting/Piping Precautions for One-Touch Tube Fittings Mounting/ Piping Caution (2) Connection of the metal rod accessories Caution Products with metal rods (KC series, (1) Connection and disconnection of tube previous KQ series, KN series, KM series, from one-touch fitting etc.) cannot be connected to KQ2 series ①...
- Page 9 Air Supply Recommended Piping Conditions (1) When connecting piping to the One-touch Warning fitting, use a pipe length with sufficient (4) Use clean air margin, in accordance with the piping Do not use compressed air that contains conditions shown in Figure 1. chemicals, synthetic oils that include organic Also, when using a tying band, etc., to bind solvents, salt, corrosive gases, etc., as it can...
- Page 10 Maintenance Warning (1) Perform maintenance and inspection according to the procedures indicated in the operation manual. handled improperly, malfunction damage of machinery and equipment may occur. (2) Maintenance work If handled improperly, compressed air can be dangerous. Assembly, handling, repair and element replacement of pneumatic systems should be performed knowledgeable...
-
Page 11: 3．Application
3. Application This product is designed to control the speed of a pneumatic actuator. 4. Specifications Fluid Proof pressure 1.5MPa Maximum operating pressure 1.0MPa Minimum operating pressure 0.1MPa -5～60℃（No freezing） Ambient and fluid temperature (note 1) Applicable tube materials Nylon,soft nylon,polyurethane,FEP,PFA Note1:Pay attention to the maximum operating pressure for soft nylon and polyurethane. -
Page 12: Construction
7.Construction Seal method/Gasket seal Seal method/Sealant For M5,10-32UNF For R,NPT Seal method/Face seal For G... - Page 13 Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 https://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. © SMC Corporation All Rights Reserved...
Need help?
Do you have a question about the ASD F-A Series and is the answer not in the manual?
Questions and answers