www.butlertechnik.com Contents Introduction The aim of the document The way of handling this document Use of symbols and emphases Warranty and responsibility Safety Intended use Safety instructions Overview Control element and menu structure Symbols Buttons and control 3.3.1 Back-function Status display Passive display mode Operating and setting Start display after switching on...
Page 3
www.butlertechnik.com Heating set-up 4.3.1 Switching on the heater by means of quick start button 4.3.2 Switching on the heater through heating menu 4.3.3 Temperature set during operation 4.3.4 Setting heating mode during operation 4.3.5 Adjusting the remaining operation time during functioning 4.3.6 Switching off heating Setting ventilation...
Page 4
www.butlertechnik.com Setting ventilation 4.8.1 Switching on ventilation by means of quick start button 4.8.2 Setting ventilation through the ventilation menu 4.8.3 Adjusting the remaining operation time during functioning 4.8.4 Switching off ventilation Timer programming 4.9.1 Creating and enabling timers 4.9.2 Deactivation, editing and removal of the programmed timer 4.9.3 Removing all programmed timers...
Page 5
www.butlertechnik.com 4.19 Setting day/night illumination 4.20 Displaying the system information 4.21 Displaying stored error information 4.22 Performing reset Cleaning Error message Error codes Disposal Technical support and customer service Technical data www.butlertechnik.com...
Please pass the instruction manual on to the later owners and users of this device. Only authorized and skilled personnel can perform an assembly. Please use only original Webasto parts. Use of symbols and emphases An emphasis Explanation...
Warranty and responsibility Webasto company does not take on the responsibility for defects and damaged caused by not following assembly and instruction manual as well as tips contained in them. The above-mentioned liability exclusion is applicable in particular for: ■...
Page 8
Risk of injuries because of faulty device Do not use the faulty heater. Contact Webasto technical support. www.butlertechnik.com...
www.butlertechnik.com Overview Control element and menu structure Heating Menu name Hour Menu symbol Quick start button with status display Activated time settings Control knob The following function settings are at the disposal in the main menu: timer, heating, ventilation and settings. Symbols Symbol Description...
Page 10
www.butlertechnik.com Symbol Description Symbol Description Heating-Normal Heating-Eco Heating-Boost Fan speed (level 1-4) Add timer Activate timer Deactivate timer Delete timer Delete all timers Active timer Quick start Day of the week Time Language Temperature unit Day/Night System information Error information Reset Service required To the left...
www.butlertechnik.com Buttons and control Button Control and function Quick start button with status display (backlight) Control knob (turn/push button) for selection and confirmation of the selected functions. 3.3.1 Back-function By means of back-function one can always leave the chosen menu and go to the previous menu level. Back Status display Status of the heater is indicated by means of the colour backlight of the quick...
Passive display mode If the heater is activated by other Webasto control element (e.g. by a radio remote control) then MultiControl/SmartControl wake up from the sleep mode and the operation mode is shown on the display by other control element (heating, venti- lation).
In order to make it possible for you to enjoy the full comfort of using Webasto heater you are requested to make yourself familiar with the instruction manual. Questions connected with the assembly and functioning of the device should be addressed to the seller or the installation workshop.
www.butlertechnik.com Start display after switching on MultiControl The following information about the connected heater and control element is shown in the start display: ThermoPro 50 Eco SW: 1.2.2 ■ Name of the connected control element HW: 1.1 ■ Name of the connected heater ■...
www.butlertechnik.com In delivery condition this function is preset with the standard values. Quick start button is programmed for heating. Press q ui ck start butt on. Heating starts functioning. Heating symbol is shown in the display as well as initially set heating temperature. Quick start button shows green light.
www.butlertechnik.com Turn the c on tro l knob in order to choose the Heating desired temperature. Press the c on tro l knob in order to confirm Temperature selection Heating starts functioning. Heating symbol and selected heating temperature are shown in the display. Quick start button shows green light.
www.butlertechnik.com Press the c on tro l knob within 5 seconds in order to confirm selection. * depending on the installed heater. 4.3.5 Adjusting the remaining operation time during functioning The heater is in the heating mode. Press the c on tro l knob in order go from tem- perature selection to heating mode selection.
www.butlertechnik.com 4.3.6 Switching off heating The heater is in the heating mode. Press q ui ck start butt on. Display shows the main menu. Heating Backlight of quick start button changes its colour from green into white colour. Setting ventilation Ventilation function activates only the fan, heating function is still on.
www.butlertechnik.com 4.4.1 Switching on ventilation by means of quick start button “Quick start” function enables heating or ventilation by simply pressing the but- ton. In ventilation mode one can initially set fan speed, operating time. Instruction manual and description of the settings can be found in the chapter “Setting the quick start”.
www.butlertechnik.com Turn the con tro l knob in order to choose the Ventilation desired duration of “an hour”. Duration By means of turning the control knob in clock- wise direction one can select and activate maximum duration. Press the con tro l knob in order to confirm selection.
www.butlertechnik.com Press the con tro l knob within 5 seconds in order to confirm selection. 4.4.4 Setting fan speed during operation The heater is in the ventilating mode. Press the con tro l knob in order go from remaining operation time selection to fan speed selection.
www.butlertechnik.com Timer programming This function is available for control element of MultiControl. There is a possibility of programming the time settings 7 days in advance. The heater switches on automatically at the programmed time. There is a possibility of saving up to 3 time settings per day and altogether up to 21 time settings. Depending on the used variant of MultiControl device and application case (e.g.
Page 23
www.butlertechnik.com Turn the con tro l knob in order to choose the Timers switch-on time of “an hour”. Press the con tro l knob in order to confirm Start time selection. Turn the con tro l knob in order to choose Timers switch-on time of “a minute”.
Page 24
www.butlertechnik.com Turn the con tro l knob in order to choose the Timers desired heating mode. Normal Options available: Eco (power saving mode), normal (comfort heating), Boost (rapid heating). Press the con tro l knob in order to confirm selection. Turn the con tro l knob in order to choose the Timers desired temperature.
Page 25
www.butlertechnik.com One should set the timer for “ventilation” operation mode. Turn the con tro l knob in order to choose the Timers desired “Ventilation” mode. Press the con tro l knob in order to confirm Ventilation selection. Turn the con tro l knob in order to choose the Timers desired fan speed.
www.butlertechnik.com 4.5.2 Deactivation, editing and removal of the programmed timer “Timer” symbol has been selected in the main menu. Timers Press the con tro l knob. The stored timers appear in the display. Timers are arranged in chronological order according to days/hours.
www.butlertechnik.com Press the c ont ro l knob. The stored timers appear in the display. Turn the con tro l knob clockwise until “Delete all” message is shown in the display. Timers Delete all Press the con tro l knob in order to confirm Timers selection.
www.butlertechnik.com Press q ui c k start but ton. Heating starts functioning. Heating symbol and preset remaining operation time appear in the display. Quick start button shows green light. 4.7.2 Switching on the heater through heating menu Heating symbol has been selected in the main menu. Heating Press the c on tro l knob.
www.butlertechnik.com Turn the c on tro l knob in order to choose Heating duration of “a minute”. Press the c on tro l knob in order to confirm Duration selection. Heating starts functioning. Heating symbol and preset remaining operation time appear in the display.
www.butlertechnik.com 4.7.4 Switching off heating The heater is in the heating mode. Press q ui ck start butt on. The main menu appears in the display. Heating Backlight of quick start button changes its colour from green into white colour. Setting ventilation 4.8.1 Switching on ventilation by means of quick start button “Quick start”...
www.butlertechnik.com Press the con tro l knob. Operation time flickers in the display. Turn the con tro l knob in order to choose the Ventilation duration of “an hour”. By means of turning the control knob in a clock- Duration wise direction one can select and activate maximum duration.
www.butlertechnik.com Press the c on tro l knob within 5 seconds in order to confirm selection. 4.8.4 Switching off ventilation The heater is in the ventilating mode. Press q ui ck start butt on. The main menu appears in the display. Backlight of quick start button changes its colour Heating from blue into white colour.
Page 33
www.butlertechnik.com “Timer” symbol has been selected in the main menu. Timers Press the con trol knob. Timers “Add timer” message (if no timer has been saved yet) appears in the display. Add timer Press the con trol knob in order to add new timer.
Page 34
www.butlertechnik.com Turn the con trol knob in order to choose the Timers stop time of “an hour”. Press the con trol knob in order to confirm Stop time selection. Turn the c ontrol knob in order to choose the Timers stop time of “a minute”.
www.butlertechnik.com Press c ont ro l knob in order to confirm selection. Numbering of timers is established according to programming sequence. Activated time setting is marked by white bars. “T” symbol appears in the main menu. Quick start button flashes green when timer together with heating is active but the display is off.
www.butlertechnik.com Turn the con tro l knob in order to choose Timers operation (activate/deactivate/edit/delete). Deactivate 4.9.3 Removing all programmed timers “Timer” symbol has been selected in the main menu. Timers Press the con tro l knob. The stored timers appear in the display. Turn the c ontrol knob clockwise until “Delete all”...
www.butlertechnik.com 4.10 General settings 4.11 Quick start settings of air heaters 4.11.1 Setting the heating “Settings” symbol has been selected in the main menu. Settings Press the con tro l knob. Settings Press the con tro l knob in order to choose “Quick start”...
www.butlertechnik.com Turn the con tro l knob in order to choose the Heating desired temperature. Press the con tro l knob in order to confirm Temperature selection. Duration flickers in the display. Turn the c ontrol knob in order to choose Heating the duration of “an hour”.
Page 39
www.butlertechnik.com Press the con tro l knob. Settings Press the con tro l knob in order to choose “Quick start” submenu. Quick start Heating mode appears in the display. Turn the c ontrol knob in order to choose the Settings desired “Ventilation”...
www.butlertechnik.com Turn the con tro l knob in order to choose the Ventilation duration of “a minute”. Press the con tro l knob in order to confirm Duration selection. Quick start button is configured by means of the appropriate settings. 4.12 Quick start settings of water heaters 4.12.1 Setting heating “Settings”...
www.butlertechnik.com Turn the con tro l knob in order to choose the Heating duration of “an hour”. By means of turning the control knob in a clock- Duration wise direction one can select and activate maximum duration. Press the con tro l knob in order to confirm selection.
www.butlertechnik.com Turn the con tro l knob in order to choose the Settings desired “Ventilation” mode. Press the con tro l knob in order to confirm selection. Duration flickers in the display. Turn the c ontrol knob in order to choose Ventilation the duration of “an hour”.
www.butlertechnik.com Press the con tro l knob. Settings “Quick start” symbol is shown in the display. Quick start Turn the c ontrol knob in order to choose the Settings desired ”Day” symbol. Press the con tro l knob in order to confirm Weekday selection.
www.butlertechnik.com Turn the con tro l knob in order to choose Settings the desired time format (12/24). Press the con tro l knob in order to confirm Time mode selection. Hour flickers in the display. Turn the c ontrol knob in order to choose Settings “an hour”.
www.butlertechnik.com Turn the con tro l knob in order to choose Settings the desired “Language” symbol. Press the con tro l knob in order to confirm Language selection. Turn the c ontrol knob in order to choose the Settings desired “language”. English Press the con tro l knob in order to confirm Language...
www.butlertechnik.com 4.17 Setting brightness “Settings” symbol has been selected in the main menu. Settings Press the con tro l knob. Settings “Quick start” symbol is shown in the display. Quick start Turn the c ontrol knob in order to choose Settings the desired “Brightness”...
www.butlertechnik.com Turn the con tro l knob in order to choose the Settings desired “Screen timeout” symbol. Press th e c o ntrol knob in order to confirm Screen timeout selection. Turn the con tro l knob in order to choose Settings the desired time or “Auto”...
Page 48
www.butlertechnik.com Turn the con tro l knob in order to choose Settings the desired ”Day/Night” symbol. Press the con tro l knob in order to confirm Day/Night selection. “Off” option is preset. Turn the con tro l knob in order to set the value Settings for the start of the day, the end of the day, bright- ness during a day, brightness at night.
Page 49
www.butlertechnik.com Turn the con tro l knob in order to choose the Settings desired start of the day “a minute”. Press the con tro l knob in order to confirm Start of daytime selection. Time of “an hour” for the end of the day flickers in the display.
www.butlertechnik.com Turn the con tro l knob in order to choose the Settings desired brightness level ”night”. Press the con tro l knob in order to confirm Brightness (Night) selection. Settings “Day/night” brightness level appears in the display. The selected values have been saved. Day/night illumination is activated.
www.butlertechnik.com Press the con tro l knob in order to confirm Settings selection. Heater The heater name is shown in the display. Turn the con tro l knob in order to switch Settings between the names of the heater and information regarding control element (the name of the con- trol element, status of software and equipment).
www.butlertechnik.com Turn the con tro l knob in order to choose the Settings desired “Error information” symbol. Error information Press the con tro l knob in order to confirm Settings selection. Error message (-s) is (are) shown in the display. If there is no error message then „OK.”...
www.butlertechnik.com Press the con tro l knob. Settings “Quick start” symbol is shown in the display. Quick start Turn the c ontrol knob in order to choose the Settings desired “Reset” symbol. Reset “OK” is shown in the display. Press the con tro l knob in order to confirm Settings selection.
www.butlertechnik.com Error message is shown in the display. Press the con tro l knob in order to confirm error message. Error message is stored in error memory. If error message is not confirmed then it will be displayed during each restart/waking up from the stand-by mode.
Code Description Wrong time (internal clock chip of MultiControl/SmartControl device lost its time) In case of voltage interruption amounting to more than 8 minutes: Enter date/hour again. In case an error appears without voltage interruption: Contact technical support/customer service.
Page 56
82199 Gilching Germany Visiting Address: Friedrichshafener Str. 9 82205 Gilching Germany Internet: www.webasto.com The telephone number of each country can be found in the Webasto service center leaflet or the website of the respective Webasto representative of your country. www.butlertechnik.com...