Before Starting The Equipment - EINHELL REDAXXO 36/25 Original Operating Instructions

5. Before starting the equipment

Warning!
Always remove the battery/batteries before
making adjustments to the equipment.
The garden shredder is delivered unassembled.
The chassis and the wheels must be fi tted before
use. Follow the operating instructions step-by-
step and use the pictures provided as a visual
guide to easily assemble the machine.
5.1 Assembling the chassis (Fig. 4)
•
Pull the hex key (Fig. 3 / Item 16) out of the
holder.
•
Place the motor housing upside down on the
floor.
•
Insert the chassis (Item 5) into the provided
openings as far as it will go.
•
Secure the chassis, as shown in Fig. 4, using
the screws (Item 15).
5.2 Assembling the axle and wheels
(Figs. 5-9)
•
Insert the axle through the chassis
•
Fit the sleeves on both sides
•
Attach the wheels on both sides
•
Insert a screwdriver through the holding hole
on the axle and secure the wheels with the
screws
•
Fit the wheel caps to the wheels; make sure
that the clips (A) on the wheel caps latch into
the recesses on the wheels.
5.3 Prodder holder (Fig. 10)
Push the prodder (Item 8) into the holder (Item
12a).
5.4 Inserting the hex key into the holder
•
Swing open and remove the loading funnel
(Fig. 11 / Item 2) by opening the release
screw (Fig. 11 / Item 10).
•
Push the hex key (Fig. 12 / Item 16) into the
hole provided for it in the ejector housing.
•
Insert the loading funnel (Fig. 13 / Item 2) into
the hooks on the ejector housing and swing
the housing shut.
•
Check that the loading funnel (Fig. 14 / Item
2) is correctly seated and retighten the re-
lease screw (Fig. 14 / Item 10).
Note: The hex key can be used to loosen the
blade screws.
Anl_Redaxxo_36_25_SPK13.indb 21 Anl_Redaxxo_36_25_SPK13.indb 21
GB
5.5 Fitting and charging the battery
Fitting the battery (Fig. 15)
Note: The cover fl ap (Item 3) is self-closing and is
kept shut by magnets.
Open the cover fl ap. Push the two batteries into
the battery mounts. Make sure that the pushlock
button (Item C) latches in place as soon as the
battery has been pushed fully in. To remove the
batteries, proceed in reverse order.
Important!
The equipment's operating time depends on
the battery with the lower charge level or lower
capacity (Ah). Therefore, only use rechargeable
batteries which are charged to the same level and
have the same capacity (Ah). Never combine full
and half-full batteries or batteries with diff erent
capacities (Ah).
Always charge the two batteries simultaneously
before starting to use them.
Batteries with a capacity rating of 5.2 Ah or higher
are recommended for the best performance.
Charging the battery (Fig. 16)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to blink.
3. Insert the battery pack into the charger.
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
- 21 -
25.07.2023 11:51:46 25.07.2023 11:51:46