Advertisement
METHOD 3: JR/SPEKTRUM SATELLITE CONNECTIVITY METHOD
53¢=:JR/SPEKTRUMA)R
EIR
|
Poe
1. Do not mix satellite receivers of different makes.
2. Even under correct startup sequence,
if transmitter is
powered
off first, LED1~LED5 will also flash. Thus the
3. 3GX supports satellite receiver models currently available on
the market. Should new receiver version comes out with,
compatibility issues, firmware will be updated to resolve any
incompatibility that may arise.
1. PORRO
18 BAAR IDEA»
2. TEM RAGDIBE FR ORAR wp o
T
A
Ue' PAEARU > FSRA SA
3. ROMS
RE IRAE ME SHOT : HUMMENINER A
setting, all channels will hold atthe last command
position,
except throttle channel which goes to a preset position.
1. Push throttle Stick tothe desired fail safe position.
2.Plug the binding plug into 3GX's BIND port, and perform
radio binding steps.
The last position hold function will be active after
the 3GX
initializes.
4.Test Method: Power off transmitter. The throttle channel
should
move to preset position, while all other channels
should hold in their last position.
setting, all channels will move to the pre-set position.
3GX. After the rapid flash of satellite's LEDs, pull the
binding plug off.
the rapid flash, following by slower flash.
while the LED is flashing in slower mode.
be set after the 3GX initializes.
————
| THR RUD PIT ELE AIL
receiver should
always be powered off before the transmitter.
3.After
successful binding, do not power off the 3GX, unplug
the binding plug and allow
3GX to enter initializing process.
When helicopter lost connectivity with your radio under this
1. Plug the binding plug into 3GX's BIND port, and power up the
2. Power up radio transmitter, and perform radio binding steps.
After radio is bound, LED on the satellite antennas will end
3. Move the transmitter sticks to the desired failsafe position
4. Satellite antenna's LED will lit up after 5 seconds, and 3GX
goes through initializing process.
The failsafe position will
1. For JR or Spektrum satellite receivers, connect wires as
shown in diagram.
2. While using the speed controller that not including BEC, you
need to connect the BEC power with 3GX "BATT"port.
To avoid damage to servos, only digital servos should be
used for swashplate.
Recommended spec: 0.08s/60
or faster,
with 12Kg or higher torque.
4. 3GX has built in speed governor function which can be
utilized by purchasing the optional speed sensor.
Governor
setting is done through channel 7 on the receiver. Channel
5/GEAR controls RPM of speed governor, channel 7/AUX2
controls rudder gyro gain.
For radios with less than 6 channels, please use the standard
receiver connectivity method.
For radios with less than 6 channels, channel 5/GEAR is used
for rudder gyro gain. Speed governor cannot be used. For
safety concern, two satellite receives should be used, with
each antenna
perpendicular (90 degrees) from each other. A
satellite receiver
should be installed on each side of the
frame, separate by minimum distance of 5cm.
Should both satellite receivers loose connectivity during flight,
LED1 ~ LEDS will flash continuouslyas warning. A single
power cycle of the system will not clear this error. The system
need to be power cycled the second time to reset.
default channel/function mapping when using satellite
receiverare:
(1)THR
(2)AlL@(3)ELE
(4)RUD_
(5)GOV)(6)PIT
(7)GAIN
1. RFR BD TTR»
SSXSESpektrumAVIR
Amie AAR
2. {ERRBECH HNE
i AN SSXAMBATT'
FLEA BEC WA °
Sec FRVAZRRUIRE
SUS ERIREAR
ERIE : 80.08/60% LIPIA A7)12kg lE °
A 3GXA RERA
MERRTE
» CORCA
ER
(5)GEAI
p
g (TVAUX22
BIA BLURS © EDA TERE
QSewaees
2
i:
SALSA
MBE
LMORLAR
MARSARBLRUA
LIONS
DBAS
SINES MAR ARBLSADLLE «
ay gt
VARERNE
ENAA
LED1 ~LEDS GFP
ean
ee BAS » Le ~LEDS SSMS
TOAGA BOM DA
PBL —R » A OLE AME
#
bal
ad
™
| 7- PARESI
ARMU DEEA :
(I)THR (2)AIL (3)ELE (4)RUD (5)GOV (6)PIT (7)GAIN
When helicopter lost connectivity withyour radio under this
ELERT,
BiG) MF SSeS
M + PRB PIA
AR
ARABS ARIES
U E .
1.
BPE RAE
EM REO RRR
iw
. HEAR
AH ESSXAVBIND IGA + MTGE
ORA
HNL ©
. BRE ISS 5c LEAD TE
TEGER
+ Fe HG Hs PAE BA
ae
+ ICX
METAL
+ BITC RBM eS
SRE.
4. MED
: HEIs BSBA
RT DARRAR
eS tt BD
REGAASMORK
HIS
-
2.
3.
[When using DSMX remote receiver, need to press 3GX SET bottom
first, then turn on the power and start binding process.
ELRAR
SUNRARRELSAB
HARBRRRAL
WB
1. NAAS
EISXGIBINDIGA » AMASGXB IR SMHLARL
LEDR
RPS RG + TERIAL
OA IRER ©
2. BRESSSR:
AIRES
SOA ADI
HATS
AE
FRLLEVSHRAGS KEM
CGRBRLUARRAE
-
3. 3
pelea RERE LON BER MEK CH BBO A
4. ETEN
SGX
A BIRRE > FICXAE N
E OTRRARERE -
ARDA : PETS
HAABAARRS
1H
When using DSMX remote receiver, need to press 3GX SET bottom
first, then turn on the power and start binding process.
OREA DSMX
SAR, SARE 3GX SET H, SHAMS RAVA «
Advertisement
