Advertisement
1. AILERON ROLL RATE RHEA
Setting Instruction:
1.After entering setting mode, STATUS LED flashes once.
2.Aileron and elevator rate can be adjusted independently.
3.Moving the aileron stick will display aileron roll rate on the LED. The more LEDs, the faster the roll rate. Moving the aileron stick
can increase or decrease the number of LEDs that lights up between LED1 to LEDS, which sets the aileron roll rate. Same method
is used to adjust the elevator flip rate when elevator stick is moved.
4.Elevator flip rate is a ojusted based on aileron roll rate. When the difference between elevator flip rate and aileron roll rate differs by
20% or more, 3GX will automatically adjust until the error rate falls within range. Therefore, we recommend adjustment aileron roll
rate first, and then adjust elevator flip rate.
5.Moving the related control stick, LED will automatically
jump to the set rate display of the specific stick function.
For example,
ones the aileron stick, LED1 to LEDS will display aileron set rate. Moving elevator stick,
LED to LEDS5 will display elevator set rate.
e
TIERS TATUSSOIBGEEOLA—— +
2. BSE
be OVER OI DID BASIE *
E :
3. AMEE
S AMET RAGE
ZLEDISR » ERMSATRSMR
SHE
MEFTLUSMABLLEDI-LEDS
HERS
EMABMR
RGR
A
FED A AEACIEIS BRAM
RRS
ZLEDISHE » TARAS -
aE
al
BARRIS
AIRRGRSE20% Yb » IGXSSHAZARRAEREROA
MAULAABBSRRGRE -
RNR
5. SNEREIFLEDGSMMBASISRED » PHS MIEIS + LEDI~SHAAMSIRQE - MAE
LEDI~SBRTARREE >
2. ELEVATOR END POINT SETTING
ARRTERPRRE
Setting Instruction:
1.Before entering elevator and aileron limit setting, please switch.the transmitter to throttle hold mode and push the throttle
down to 0° position to avoid mechanical interference due to excess travel ranges
2.After entering setting mode, STATUS LED flashes twice
3.After entering setting mode, elevator may deviate assmuch as 8 degrees plus compensating rate either forward or back.
Moving elevator stick can adjust servo travel limit: For example, if LED shows 50%, total elevator travel range is 8+0.5*8 =
12 degrees.
4.Generally 70% is suitable for most helicopter frame. If recommended value is not used, please adjust setting until
maximum is reached without mechanical binding.
BERA :
1 SEA FH ENDIE
RIEAN,
EREL,
DER
EOE
ESTRANGED
2A BRIE RS TATUS AIRES IRMA
©
SHEA RH RAR RBS
+ INRIA STEN
EANET
Es AR TIZUIR < HIMDLEDEATEQE
50% » HPRALTLMTIZAIAS+0.5°8=12/E ©
4 — (RDS 70%
LGA SARA
EH
EN
ORNL
R E "
E ESTE
E FS CORB °
STATUS Double flash
STATUSPIHERIR
3, AILERON END POINT SETTING @RiTHMRRE
Setting Instruction:
1.After entering setting mode, STATUS LED flashes 3 times.
2.After entering setting mode, aileron may deviate as much as 8 degrees plus compensating rate either forward or back. Moving
aileron stick can adjust servo travel limit. For example, if LED shows 50%, total elevator travel range is 8+0.5*8 = 12 degrees.
3.Generally 70% is suitable for most helicopter frame.
If recommended value is not used, please adjust setting until maximum is
reached without mechanical binding.
BERRA :
1.3EA ERIE RS TATUS AUIS SEPSIB ER ©
2.38), SEIS ie BSS
+ N » BORA
SRG
* ENB) RIEIST) LSS
ART SERR - PIRDLEDEAM
ERE A350% » HAL BAIAS+0.5°8=
12/8 <
3.- MMS 7% TAMARA
D DEF
AE
URMERRAE
ARESRASETSTS
RE
+
STATUS Flash in
group of 3
Advertisement
