Advertisement
SETUP PRE-CHECK
22888
While using 3GX FBL system, be sure to turn off the following functions in the transmitter
EHIGCKAMEREZSA
NDS RDA
* Swash Ring
_* Linkage Compensation
* Swash Mix
* Mixing
* Acceleration
1. Connect the receiver and servos to the flybarless control unit as per diagram found on page 4~5
2. Digital servos must be used on cyclic to avoid damage to servos.
commended servo spec: minimum speed 0.08 sec/60; torque 12kg.cm or higher.
3. The trim must be zero when using 3GX, and should not be adjusted at anytime.
If the helicopter hovering tend to one side, it
means the swashplate doesn't keep horizontal when setting. Go to flybarless system "Direct mode bypassing gyro, for
mechanical travel and neutral point setup" to adjust the level of the swashplate and then re-complete
the setup.
4. When the 3GX Flybarless system is installed for the first time, a few
simple setup steps and fly tests need to be performed
in the
flybarless setup mode.
these steps need to be performed only durin:
tial setup, and does not need to be repeated for sub-se
quent flights. Just power up the system normally, check the proper servo operations, and fly. The initial setup procedure only
need to be repeated after software upgrade, pitch range reset, or subtrims
are added in the transmitter.
1. REMBRARBKERTRO BE (WSRA4~ A) >
2. +FRUARR AUTRE > SABER
-
BARB : E0.08W/60° MA : 197)12kg.cmLLE +
3. AREA
AS EN
MRS
RIFTKIBEAMS
SEARSRROR-BED)
ATREH+FRARSKE
MEARE ORAR
BT
PAPUIMQE"
BE+FRLKTR
EMNERNE -
4.
B-RARIGCX FlybarlessMPT BRAM
UALEARPRRNERN » EARO
RR
ERRITAR TOR TABE AIR ERN > REER
W
RERE
FEARIN
: RIB MIEN - BIEN S SM SSSA MA(sub.trim iy UREA RERNBLR
LOAM e
3GX CONNECTIVITY METHOD
3CXERIR
METHOD 1:STANDARD RECEIVER CONNECTIVITY METHOD
xt—: RERS ERA
1. Connect all wires as shown in diagram, Receiverand 3GX
wires are color coded to distinguish the different connection
channels..Care should be taken to ensure proper wire color to
channel connection.
2. While using the speed controller that not including BEC, you need
'to connect the BEC power with 3GX "BATT" port.
3. Receiver power is achieved by connecting the 3GX "S.BUS/BIND"
port to the ch7 or BATT port on receiver using supplied signal wire.
4. To avoididamage to servos, only digital servos should be used for
swashplate. Recommended spec: 0.08s/60' or faster, with 12 Kg
or higher torque.
j . 3GX has built in speed governor function which can be utilized by
urchasing the optional speed sensor.
Governor setting is done
through channel 7 on the receiver.
+ BER PRT He FER
poumon
CRRA TMOREREATA
BUS » RRIF
EBSA
SHH MS
°
PAA RBECH
HNDE,
ARMA BIGXAN" BATT "FL (17 ABECRM -
$508,
38 T RE DA BA Hd BEA SR RBG XA)"S.BUS/BIND"
51 (i7ie 2 8 bE
SYBATT A i8 »
4. +FRUAS
RAAT AIRS » SA BS LIDAR
SIAL
IRURI : TO.0BM/EOLAPY : 4712kg E +
5. SGX
R ERRE
TAMERS MASE
MEREDEK
BtveeKe
en
| . For Futaba S.BUS receivers, connect wires as shown in diagram.
. . While using the speed controller that not including BEC, you
need to connect
the BEC power with 3GX "BATT" port.
Receiver power is supplied through S.BUS signal wire connected
to3GX's
"S.BUS/BIND"
port.
The default channel/function mapping when using S.BUS are:
(AIL
(2)ELE
(3)THR
(4)RUD
(5)GAIN
(6)PIT (7)GOV
AAHS.BUSI
BEA) Futabalsigs » SKIRM
Tite THER
PARBECH
18M EE
ARN. HSCXA" BATT FEA
BEC
<
EMBSSRAGBS.BU:
RIRE BISXA)"S.BUS/BIND"3/{i7 ©
ERS.BUSI REIS ' ABMIBDISER :
(AIL
(2)ELE (3)THR
(4)RUD
(5)GAIN
(6)PIT (7)GOV
Pe
oye
tated
trast
———
If channel (3) is set as PIT and channel (6)set as THR on transmitter,
THR RUD PIT ELE AIL
Such as 8FG, 12Z, 14MZ, and etc, please reprogram the transmitter
Esc
ie:
to utilize channe (3) as THR
and channe
(6) as PIT.
SPE BOVE
ASS
(3) EAP IT (6)AISASTHRES > HIUSFG - 12Z -
A4MZS + BEES
HVE
AS)BiS THR (6AE PIT >
. To avoid damage to servos, only digital servos should be used
for swashplate.
Recommended spec: 0.08s/60 or faster,
with 12Kg or higher torque.
. 3GX has built in speed governor function which can be utilized by
purchasing the optional speed sensor.
Governor setting is done through channel 7 on the receiver.
G50 OGS
. + FARA RITA
> SABES ORIER -
Do not exchange AIL
BATT out
k
Si
nok
ae
land PIriconnactions:
[ta
FR J
ERRE
BE0.08/60 DP : AIZKg LE
p
a
2
Advertisement
