Advertisement
4, SWASHPLATE DAMPENING SETTING
+3 #221bR=
Setting Instruction :
1. After entering setting mode, STATUS LED flashes 4 times.
2. Move the aileron stick to adjust cyclic pitch dampening rate; the more LED lights up, the more dampening effect. Please note
aileron and elevator dampening cannot be adjusted separately.
Moving aileron stick is for adjusting cyclic pitch dampening
rate, but moving elevator stick is for adjusting collective pitch dampening rate, NOT elevator dampening rate.
3. The more dampening effect, the smoother helicopter flies, but feels less direct. The rate of dampening should be adjusted to
suit pilot's preferences.
SEA SRIERSTATUS
BIE SEPIEOR +
2 BREN
Gem ROE LIES LEDRRHS ' RUS
SMEBVMRRABACTIDHBRE * MURAI
RIEF ABER
' (8
SENT PERCHES eae SE BSRIDAHLAZES " MIEA MERCIER ©
ee
MERTAPA: (MABE » RUEBIMGATAF
BE +
Move aileron stick to adjust cyclic
Move elevator stick to adjust
pitch dampening
STATUS F Flash in
collective pitch dampening
STATUS F] Flash in
BNURERRRERRERLA
eS
SRE We iE ER
aR Fee ft
soup ete
A
2
=
=
[
!
l
Qe Ow
coe AIL
EER
Us se
yaw
Ut)
ELE
L
Mode 1
[Mode 2]
Mode 1
Mode 2]
5. SWASHPLATE ACCELERATE SETTING
+ F018
Setting Instructio:
1. After entering setting mode, STATUS LED flashes 5 times.
2. Move the aileron stick to adjust cyclic pitch acceleration rate; the more LED lights up, the more acceleration effect. Please note
aileron and elevator acceleration cannot be adjusted separately.
Moving aileron stick is for adjusting cyclic pitch acceleration
rate, but moving elevator stick is for adjusting collective pitch acceleration rate, NOT elevator acceleration rate.
3. When cyclic pitch acceleration is active, hovering point fixation ability maybe reduced. Beginners or F3C pilots should
minimize cyclic pitch acceleration rate value, or set it to zero.
BRERA
:
2. SPUN BURRIEAL SLMS
ARIS ORS
RMS
» RAS
CHERMRRA
NASI
A R M S » MAME
RISE A
RMN
» BING)
PENCEN
EONS MORE
RES + MIE
Pe RCD
>
3. PORUSENIE » BSAA
ERE RAS
RSME SCH TSM
ERREN EN
U I » SURRTE ARO +
Setting swashplate acceleration may increase the burst amp draw Of servos.
Therefore, BEC output capability should
be confirmed to handle burst current when setting collective pitch acceleration, otherwise insufficient current supply
may result in flight accidents. We recommend direct power supply if acceleration is higher than 50%.
BET FARR G SAL
REE
BLS + PLA ERA ADR ALE ANGIE DOR - UAB BBECRS IRRE GT
ARES BRA E ASE MERRIE
ARREA%
FADER TELE
BRB TAIN
=
aL
ie
[Mode ||
RUDDER GYRO SETUP esetesninine
After the system reboots, part of flybariess setup is completed.
Now the rudder gyro needs to setup. Push and hold the SET
button for 2 seconds to enter the rudder gyro setup mode.
If your transmitter has the following settings, please disable it or set the value to zero.
TEXAS
SF lybarless8h)
2 ETE » BM
SRA ICRIG » HSE
THR SETRA EN ERRE
«
RO RD AVES
P SUID BERS » BARE RA ER(OFF) MIG
EAS
@aTS
@ Rudder to gyro mixing
@ Pilot authority mixing
@ Pitch to rudder mixing
@ Throttle to rudder mixing
@ Revolution mixing
3GX Flybarless rudder gyro has the factory setting of 1520 u s and DS digital servo.
Double check your servo spec
and change the gyro setting as needed to avoid damages to the servo.
3GX Flybarless FefeheMRiRU
MERE (7 : 1520 u SMSARIDSRU
RES
ZRASEL TORRE
RRNEE AGSMISAMAIR SIAR |
3GX Flybarless system is compatible with both the 760 ų s narrow frame rate servos (such as Futaba $9256, $9251, BLS251), as well
as the standard 1520 u s frame rate servos (most others). Proper frame rate must be selected based on your servo's specifications.
To enter the setup mode : Press and hold the SET button for 2 seconds until STATUS LED flashes. The 1520/760 LED will
light up indicating servo frame rate setup mode.
Push the transmitter rudder stick left or right to select the frame rate.
For
example, if rudder is pushed to the left (or right) and STATUS LED turns green, the frame rate is set to 1520 us. To setitto
760 us, the rudder stick need to be pushed from the center
to the opposing end 3 times for the STATUS
LED to turn red,
indicating frame rate set to 760 us.
3GX Flybarless panel : Each setting value is labeled on the 3GX flybarless control unit with either green or red lettering,
which corresponds to the STATUS LED color. Subsequent setup mode is entered by a single press of the SET button.
Setup mode will exit if no activity is detected in 10 seconds.
11
Advertisement
