Page 1
Технический паспорт FERMER-4,2 (EURO) FERMER-4,6 (EURO) honeycomb polycarbonate greenhouse any length multiple of 2.1 width min 4.2 m 4,15 m; 4,61 m Technical certificate р. 2-7 Assembly manual р. 8-27...
Page 2
Technical certificate Technical certificate PARAMETERS OF PACKAGES ПАРАМЕТРЫ ПАКЕТОВ Тable 2 Perform assembling and operation of the greenhouse in strict accordance with the manual and operating rules stated in the technical certificate. Please keep content dimensions,mm weight. no more kg this technical certificate for further reference.
Page 3
Technical certificate Technical certificate Extra package base Тable 3 DETAILED PARTS LIST “FRAME” (4.2 M) Таблица 4 Ridge shape 2,10 Top draw band 6,76 marking name length (m) quantity (pcs) Bottom draw band 0,60 6 PACKAGE FERMER Top arc base sheet 0,83 Stay brace 1,98...
Date of manufacture: polycarbonate sheets with a brush, metalized fabric or other abrasive materials. Manufacturer: VOLYA LLC, per. Severny, 8, Dubna, Moscow region, 141983, Russia. Do not use sulphur cartridges for disinfecting greenhouse The manufacturer bears responsibility for quality of products in accordance with RF CC. The...
Manual Manual “FERMER” GREENHOUSE INSTALLIATION MANUAL INSTALLATION SEQUENCE Introduction Stage name page The general view of the frame is presented in fig. 1. The frame is assembled from End wall assembly 12-13 the shape numbered parts. Medium shape shelves are facing the covering.. Installation of runners on the end wall Some parts have free holes Indexes:...
Page 6
Manual Manual GENERAL VIEW OF THE GREENHOUSE FRAME WITH EXTENDING GENERAL VIEW OF THE GREENHOUSE FRAME WITH EXTENDING INSERTS INSERTS Г И А Б В 2к А К Б укос В Г Д Е укос укос Д Ж Е Fig 1 General view of the greenhouse with two inserts, total length is 8.4 m.
Page 7
Manual Manual INSTALLATION SEQUENCE INSTALLATION SEQUENCE STAGE 1 Assembly of the end wall is carried out fig. 1.8 А according to the fig. 1.1.. General view of the end Д Б А wall and location of the Г angles for fastening of bolt М6х14 polycarbonate.
Page 8
Manual Manual INSTALLATION SEQUENCE INSTALLATION SEQUENCE STAGE 3 STAGE 5 fig. 5.1 End section installation Assembly of the power arc Assembly of the power In the variant of arc is carried out in a installation of the horizontal plane similar to greenhouse without a fig.
Page 9
Manual Manual DOORS ASSEMBLY INSTALLATION SEQUENCE STAGE 7 А STAGE 6 Б Doors assembly. 13-д Extension of the frame length. В Doors are assembled in Е 14-д the same way. Joints are Assembled power arc (or already been connected, shown in the figures. 13-д...
Page 10
Manual Manual DOORS ASSEMBLY DOORS ASSEMBLY 14-д Г 12-д-л 13-д 14-д Д Fig. 7.1 Arrangement of 13-д angles for fastening 12-д-п of polycarbonate on the doors. Е 12-д-п П-12-д-п screw screw STAGE 8 Installation of covering Ж Install honeycomb polycarbonate with a specified side facing outwards 12-д-л...
Page 11
Manual Manual CUTTING LIST OF COVERING OF AN END CUTTING LIST OF COVERING OF AN END 2100 2100 Reminder Reminder 1520 1550 Ridge Ridge Ridge Ridge Ridge Ridge Ridge Ridge 1303 1770 1303 1062 door door door door door door door door...
Page 12
Manual Manual FASTENING OF COVERING FASTENING OF COVERING Fig. 8.6 washer 32х6,3 Fasten the pieces of covering on the end to 2к, 2кн - places of fastening the angles with the use of of door seals. washers and self-tapping self-tapping screw places screws (fig.8.3).
Page 13
Manual Manual FASTENING OF COVERING FASTENING OF COVERING First install all the joining plates and tingles on arcs small arc base sheet Arc base bolt М6х14 sheet tingle Do not tighten up! nut М6 bolt М6х14 bolt М6х20 (from the base package) washer 32х6 (from the base package) ) outermost...
Page 14
Manual Manual FASTENING OF COVERING FASTENING OF COVERING Top draw band шайба 32х6 (из основного пакета) Top draw bolt М6х20 band main shape (from the base tingle washer 6 bottom package) (from the base draw package) band nut М6 bolt М6х14 (from the base package) straighten the...
Need help?
Do you have a question about the FERMER-4,2 and is the answer not in the manual?
Questions and answers