Page 1
FERMER-5 (EURO) honeycomb polycarbonate greenhouse any length multiple of 2.1 width 5,0 m min 4.2 m Technical certificate р. 2-7 Assembly manual р. 8-27...
Page 2
4.2 m is 21 m2. Height of the installed 2155х90х60 7 PACKAGE FERMER-5,0 (end elements) frame is 2.86 m. 8 PACKAGE FERMER-5,0 (elements and strips for doors) 1900х90х80 13,0 The frame of the greenhouse is made of galvanized iron 1 mm thick and is to be 335х335х325...
Page 3
Technical certificate Technical certificate Extra package base DETAILED PARTS LIST “FRAME” (4.2 M) Таблица 4 Тable 3 Ridge shape 2,10 Top draw band 6,76 marking name length (m) quantity (pcs) Bottom draw band 0,60 6 PACKAGE FERMER Top arc base sheet 0,83 Stay brace 1,98...
Date of manufacture: materials. Manufacturer: VOLYA LLC, Do not use sulphur cartridges for disinfecting greenhouse per. Severny, 8, Dubna, Moscow region, 141983, Russia. against fungal and bacterial agents in order to prevent The manufacturer bears responsibility for quality of products in accordance with RF CC.
Manual Manual “FERMER” GREENHOUSE INSTALLIATION MANUAL INSTALLATION SEQUENCE Introduction Stage name page The general view of the frame is presented in fig. 1. The frame is assembled from End wall assembly 12-14 the shape numbered parts. Medium shape shelves are facing the covering.. Installation of runners on the end wall Some parts have free holes Indexes:...
Page 6
Manual Manual GENERAL VIEW OF THE GREENHOUSE FRAME WITH EXTENDING GENERAL VIEW OF THE GREENHOUSE FRAME WITH EXTENDING INSERTS INSERTS Г И А Б В 2к А К Б укос В Г Д Е укос укос Д Ж Е Fig 1 General view of the greenhouse with two inserts, total length is 8.4 m.
Page 7
Manual Manual INSTALLATION SEQUENCE INSTALLATION SEQUENCE STAGE 1 А Г Е bolt М6х14 bolt М6х14 Assembly of the end wall. П-9 washer 6 washer 6 bolt М6х14 Assembly is carried out washer 6 according to the figure 1.1. 7м 10-ц Б...
Page 8
Manual Manual INSTALLATION SEQUENCE INSTALLATION SEQUENCE STAGE 3 fig. 1.8 General view of the end Assembly of the power arc wall and location of the angles for fastening of Assembly of the power arc is polycarbonate. carried out in a horizontal plane similar to the assembly of the end wall.
Page 9
Manual Manual INSTALLATION SEQUENCE INSTALLATION SEQUENCE STAGE 6 STAGE 5 fig. 5.1 End section installation Extension of the frame In the variant of length. installation of the Assembled power arc (or already been connected, greenhouse without a other end wall, depending and so on all the arcs are foundation, marking on the needed length...
Page 10
Manual Manual DOORS ASSEMBLY DOORS ASSEMBLY 14д Г А 12дл 13д Б Doors assembly. 13д В Doors are assembled in Е 14д the same way. Joints are shown in the figures. 13д 14д Strips and other surface mounted components are Д...
Page 11
Manual Manual DOORS ASSEMBLY CUTTING LIST OF COVERING OF AN END 2100 Reminder fig. 7.1 Arrangement of 1520 angles for fastening of polycarbonate on the doors. 1500 STAGE 8 Ridge Installation of covering Ridge Install honeycomb polycarbonate with a specified side facing outwards (sunward);...
Page 12
Manual Manual FASTENING OF COVERING FASTENING OF COVERING Fig. 8.5 Fasten the pieces of covering on the end to - places of fastening the angles with the use of of door seals. washers and self-tapping self-tapping screw places screws (fig.8.2). fastening of penofol.
Page 13
Manual Manual FASTENING OF COVERING FASTENING OF COVERING First install all the joining plates and tingles on arcs small arc base sheet Arc base bolt М6х14 sheet tingle washer 6 Do not tighten up! nut М6 bolt М6х14 bolt М6х20 (from the base package) washer 32х6 (from the base package) )
Page 14
Manual Manual FASTENING OF COVERING FASTENING OF COVERING top draw band washer 32х6 (from the base package) bolt М6х20 (from the base washer 6 package) кляммер main shape (from the base top draw bottom package) band draw band bolt М6х14 Arc base straighten the Base sheet...
Need help?
Do you have a question about the FERMER-5 and is the answer not in the manual?
Questions and answers