Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for UNI-T UPO1000 Series
Summary of Contents for UNI-T UPO1000 Series
- Page 1 Quick Guide UPO1000 Series Digital Phosphor Oscilloscope...
- Page 2 UNI-T is the registered trademark of Uni-Trend Technology (China) Co., Ltd. File Version 20230822-V1.00.0018 Statement UNI-T products are protected by patent rights in China and foreign countries, including issued and pending patents. UNI-T reserves the rights to any product specification and pricing changes.
-
Page 3: Safety Requirements
Users must follow the following conventional safety precautions in operation, service and maintenance of this device. UNI-T will not be liable for any personal safety and property loss caused by the user’s failure to follow the following safety precautions. - Page 4 Quick Guide UPO1000 Series Grounding Frame and chassis grounding terminal Grounding Protective grounding terminal Grounding Measurement grounding terminal Main power off Main power on Power Standby power supply: when the power switch is turned off, this Supply device is not completely disconnected from the AC power supply.
- Page 5 Please use power fuse of specified specification. If the fuse needs to be replaced, it Power fuse must be replaced with another one that meets the specified specifications by the maintenance personnel authorized by UNI-T. There are no components available to operators inside. Do not remove the Disassembly and protective cover.
-
Page 6: Environmental Requirements
If this device may be faulty, please contact the authorized maintenance personnel of Abnormality UNI-T for testing. Any maintenance, adjustment or parts replacement must be done by the relevant personnel of UNI-T. Do not block the ventilation holes at the side and back of this device;... -
Page 7: Electrostatic Protection
Quick Guide UPO1000 Series Please install AC power cable as follows. Ensure the power cable is in a good condition. Leave enough space for connecting the power cord. Plug the attached three-prong power cable into a well-grounded power socket. - Page 8 UPO1054 50 MHz 2 GSa/s UPO1000 series digital phosphor oscilloscope adopts UNI-T 3D technique Ultra Phosphor 2.0 with new appearance upgrade and the function of deep storage, high waveform capture rate, real-time waveform recording and playback and 256-level grayscale display.
-
Page 9: General Inspection
This chapter is to introduce on using the oscilloscope for the first time, the front and rear panels, the user interface, as well as the built-in help system. 3.1 General Inspection It is recommended to inspect the instrument follow the steps below before using the UPO1000 series for the first time. (1) Check for Damages caused by Transport If the packaging carton or the foam plastic cushions are severely damaged, please contact the UNI-T distributor of this product immediately. - Page 10 Quick Guide UPO1000 Series Probe compensation Ground terminal signal connecti n clip Figure 4-1 Probe Compensation Signal Connection Clip and Ground Terminal (4) Function Check Press the AUTO key, a 3 Vpp, 1 kHz square wave should appear on the screen. Repeat step 3 to check all channels.
-
Page 11: Front Panel
Quick Guide UPO1000 Series 4. Front Panel ○ Figure 3 Front Panel Table 1 Function Key of Front Panel Function Key Function Key Screen display area Horizontal control area (HORIZONTAL) Multipurpose rotary knob Analog channel input port Navigation function area... -
Page 12: Rear Panel
Quick Guide UPO1000 Series 5. Rear Panel Figure 4 Rear Panel Table 1 Function Key of Rear Panel Function Key Function Key EXT Trig Power switch AUX Out (output port) and Power input socket，refer to arbitrary waveform signal output Connecting Power Supply... -
Page 13: User Interface
Quick Guide UPO1000 Series 6. User Interface Figure 5 User Interface Table 3 Icon of User Interface Description Description Trigger status Next page /System time/USB icon/LAN icon Horizontal time base CH4 state label Horizontal offset CH3 state label Waveform indicator... - Page 14 7. Menu Symbol Press any soft key to activate the corresponding menu, the following symbol may display in the menu. represents use the multipurpose rotary knob to select the parameter and adjust the parameter value. represents the current menu have several options. represents the current menu has a next menu.
- Page 15 UPO1000 Series 8. Remote Control UPO1000 series digital phosphor oscilloscope supports communicate with computer through USB interface and LAN interface, so as to realize remote control. Remote control is based on SCPI (Standard Commands for Programmable Instruments) to realize. UPO1000 series digital phosphor oscilloscope supports three methods for remote control.
-
Page 16: Troubleshooting
After completing the above steps, restart the oscilloscope. If you still cannot use this product normally, please contact UNI-T. After signal acquisition, the waveform of the signal does not appear in picture. Check whether the two ends of BNC line are connected properly. - Page 17 UPO1000 Series 10. Appendix Contact If the use of this product has caused any inconvenience, if you in mainland China you can contact UNI-T company directly. Service support: 8am to 5.30pm (UTC+8), Monday to Friday or via email. Our email address is infosh@uni-trend.com.cn...