Related Manuals for AAON USB-Link 2
Summary of Contents for AAON USB-Link 2
- Page 1 USB-Link 2 Technical Guide ASM02244 Software SS0073, version 4.11 and up Software SS3007, version 1.00 and up...
-
Page 2: Table Of Contents
This document is subject to change without notice. www.aaon.com It is the intent of AAON to provide accurate and current product AAON® is a registered trademark of AAON, Inc., Tulsa, OK. information. However, in the interest of product improvement, Microsoft®, Windows®, and Windows 10®... -
Page 3: General Information
Prism 2 software. The USB-Link 2 is small in size and is powered by the USB port of the computer it is plugged into, making it completely portable and allowing connection to the system from any controller. -
Page 4: Quick Guide
Quick Guide Important Notes • Follow the included USB-Link 2 driver installation instructions Follow the six steps below to get your USB-Link 2 up and running (page 5). in no time. • Follow the connection and wiring instructions (Figure 2,... -
Page 5: Usb Driver Installation
NOTE: a CommLink 5, you may already have this driver installed on your PC. If you are using a USB-Link 2 with SS3007 software, the drivers are already installed as part of Windows 10. 10. The following list of files will display. Choose 32_Bit. -
Page 6: Connection And Wiring
CONNECTION & WIRING Connection and Wiring Figure 2: USB-Link 2 Connection & Wiring USB-Link 2 Technical Guide... -
Page 7: Finding The Com Port Number
CONNECTION & WIRING Finding the COM Port Number Finding What COM Port Number the USB-Link 2 is Using Right-click on the Windows icon, located on the bottom left or top left of the Windows Tool Bar. Select <Device Manager>. Click on the plus sign next to Ports to see all of the common ports. -
Page 8: Prism 2 Setup Instructions
USB Link Stand Alone. If using network mode, select USB Link Network. The position of the slide If Prism 2 is online, click the switch on the USB-Link 2 must also be set to the mode you button to make it go <ON LINE>... - Page 9 16. If Units Found on this Loop stays at zero, check the 12. From the menu on the main toolbar, <Communications> wiring to the USB-Link 2 and the controller and/or read select <Search for Units> through these directions again to make sure all steps were followed.
-
Page 10: Communication Settings And Led Descriptions
Indicates communication activity between the USB TX & USB RX - the USB-Link 2 should be set to “Network” any time there is a USB-Link 2 and the computer that the USB-Link 2 is CommLink or MiniLink wired to the communications loop. -
Page 11: Troubleshooting
Prism 2. of Windows operating the Prism program. Some new • If the USB-Link 2’s USB LEDs fail to blink, disconnect and models of laptops running the latest release of Windows reconnect the USB connection. 10 have also experienced issues running Prism, and we cannot troubleshoot customer computer issues. -
Page 12: Troubleshooting The Com Port Number
Make note of this number Right-click on “USB Serial Port (COM#)” and select because you will need it for your Prism 2 setup. In the Properties Window, select the <Properties>. <Port tab. Settings> USB-Link 2 Technical Guide... - Page 13 PARTS: For replacement parts, please contact your local AAON Representative. 8500 NW River Park Drive • Parkville, MO • 64152 Ph: (816) 505-1100 • Fax: (816) 505-1101 AAON P/N: G019140, Rev. K ® Printed in the USA • © September 2023 AAON All Rights Reserved...
Need help?
Do you have a question about the USB-Link 2 and is the answer not in the manual?
Questions and answers