Introduction
Since the first Revel® speakers in 1996, Revel products have stood at the forefront of loudspeaker design and performance. The PerformaBe Architectural
Series was conceived to create high-end architectural loudspeakers that share the same caliber of components and acoustic signature as the award winning
PerformaBe floor-standing and bookshelf loudspeakers. Utilizing Beryllium tweeters these architectural speakers bring unparalleled detail and accuracy along
with a sense of air and spaciousness, and a cohesive soundstage that is hard to find in any architectural loudspeakers. The Revel Be Architectural series
consists of three in-wall models and one in-ceiling model that can be used as a complete architectural system solution or combined in a mix and match
solution with the floor-standing and bookshelf PerformaBe loudspeakers.
For more information on the set-up and operation of this product refer to the specific loudspeaker's product page on the
further assistance be required feel free to contact customer support at the numbers below:
Inside the US and Canada: +1 888.691.4171
Box Contents
1x PerformaBe Architectural Loudspeaker
1x Zero Bezel Grille
1x White Replacement Grille Scrim
1x Black Replacement Grille Scrim
1x Cutout Template
1x Quick Start Guide (This Document)
Note:
If you suspect that there has been shipping damage or if you are missing any of the referenced above Box Contents for your model, report it
immediately to your dealer or contact our Customer Support at the telephone numbers referenced in the opening of this document.
This document covers the installation of the speakers only. Refer to the Revel PerformaBe Backbox OR Pre-Construction Bracket Installation
Guide for details on installing the backboxes.
IMPORTANT!! Safety Information
IMPORTANT!
damages resulting from improper installation or a fallen loudspeaker.
Read through this document and other documents associated with this product in their entirety and heed all warning before proceeding with the
installation of these product(s).
IMPORTANT!
1.
Allow sufficient clearance between the speaker and any insulation that may be in the wall cavity to avoid ignition should overheating occur.
1" (26mm) for Non-Flammable Materials
3" (78mm) for Flammable Materials
2.
Ensure that all wire used inside of walls and ceiling meets or exceeds local fire codes for hidden wiring.
3.
Determine wire lengths and select the proper gauge speaker wire to use based on the table above titled "Wire Guage by Distance Guide".
4.
Do NOT overtighten the mounting "Cat Claws" when securing the speaker to surfaces as this may cause the speaker to come loose. If using a
power screwdriver set it to the lowest torque settings.
5.
Do NOT connect the speakers to an amplifier rated above the recommended amplifier power. Overdriving the speaker can cause an overheating
condition increasing the risk of injury.
6.
Do NOT connect the amplifier end of the wire until all speakers are wired and installed.
7.
Determine and purchase any accessories such as pre-construction brackets or backboxes before beginning the installation process. Refer to the
Specification Table at the end of this installation guide for a list of available accessories associated for each model.
8.
Ensure that wall and ceiling wallboard material is between 0.4-inch (10mm) and 1.0-inch (25mm) thick and capable of supporting the weight of the
speaker.
Installation Considerations
Revel architectural speakers are extremely easy to install. However, if you are unable to understand and follow the instructions in this manual clearly and fully,
or if you are unsure of your ability to install these loudspeakers properly, please contact your dealer or a qualified installer.
Your new Revel PerformaBe Architectural loudspeakers have been engineered to provide extremely accurate performance. However, any speaker's ultimate
performance will be affected by the speaker's placement in the listening room and the acoustics of the room. Not all listening spaces can accommodate the
ideal conditions of these two factors. Therefore, careful attention to the placement of your Revel PerformaBe Architectural loudspeakers will have a significant
impact on the general performance of the loudspeakers.
Although the Revel PerformaBe Architectural W226Be and W228Be are designed for use primarily as front left, center and front right speakers in a home
theater system, the high-order crossover networks employed in all Revel PerformaBe Architectural loudspeakers provide very smooth response over a wide
listening area, allowing you to use any model in any application with excellent results.
Note: The Revel PerformaBe Architectural in-wall speakers W226Be and W228Be can be used in either horizontal or vertical orientation.
PerformaBe Architectural Quick Start Guide | rev1.1 20230822
©2023 Harman International | Features, Specifications, and Appearance subject to change without notice.
PerformaBe Architectural Installation Guide
W126Be – W226Be – W228Be – C128Be
HARMAN International assumes no responsibility for improper installation of hardware or for any personal injuries or product
Installation Precautions
Outside the US and Canada: +44 1707 668 012
Wire Gauge by Distance Guide
Distance/Length
< 50ft (15m)
50ft (15m) ~ 100ft (30m)
>100ft (30m)
revelspeakers.com
website. Should
Min. Recommended Wire Gauge
14-gauge
12-gauge
10-gauge
Pg 1 of 6