Swegon ESENSA PX TOP 05 Installation Instructions Manual
Hide thumbs
Also See for ESENSA PX TOP 05:
- Installation instructions manual (21 pages) ,
- Installation instructions manual (29 pages)
Related Manuals for Swegon ESENSA PX TOP 05
Summary of Contents for Swegon ESENSA PX TOP 05
- Page 1 Installation instructions for the product range ESENSA Consult the latest version of this manual on our website: www.swegon.com...
-
Page 2: Table Of Contents
3.2 Drain-pan (ESENSA PX TOP) ....8 3.3 Temperature sensor T5 .......9 4. Unit power supply and start-up..10 5. Main switch........ 10 6. Operation & commissioning manuals.10 7. Options/accessories documentation. 11 8. Main board ........ .12 www.swegon.com We reserve the right to alter specifications. -
Page 3: Symbols And Abbreviations
MOTORISED DAMPER BACKWARD CURVED FAN ELECTRICAL HEATING COIL Must be connected by a qualified electrician. WARNING ! Warning! Hazardous voltage. OUTDOOR AIR (1) EXHAUST AIR (3) EXTRACT AIR (2) SUPPLY AIR (4) www.swegon.com We reserve the right to alter specifications. -
Page 4: General
CAUTION : The unit is attached to the pallet at the feet by metal parts. Unscrew the fasteners before removing the device from the pallet. www.swegon.com We reserve the right to alter specifications. -
Page 5: Product Overview
2.2 Maintenance area Front unit Front unit Model Unit (without coil) (with coil) size [mm] [mm] ESENSA PX TOP 1040 1260 It is also recommended to have 600mm either side of the unit. www.swegon.com We reserve the right to alter specifications. -
Page 6: Components
F. Electric terminal block + Earth wire connector O1/O2. Mini-pleated filter G1/G2. Pressostat P. Counter air flow heat exchanger H. Power supply/switch Q. Hydraulics connection membrane I1/I2. Membrane entry grommet (supply cable) R1/R2. Pressure tappings www.swegon.com We reserve the right to alter specifications. -
Page 7: General Installation
The ducts should be insulated according to local regulations and customary trade standards. CIRCULAR CONNECTION : Tape and seal not included RECTANGULAR CONNECTION : Seal not included Max 300 mm between each self-drilling screw (not provided) www.swegon.com We reserve the right to alter specifications. -
Page 8: Drain-Pan (Esensa Px Top)
If this conditions are not respected, that could cause an issue for the drain-pan. www.swegon.com We reserve the right to alter specifications. -
Page 9: Temperature Sensor T5
Secure the bracket to the duct (2 screws not provided) Connect the sensor’s quick-fit connector to the specific sockets on the control circuit board of the air handling unit. RIGHT VERSION Sensor electrical connection www.swegon.com We reserve the right to alter specifications. -
Page 10: Unit Power Supply And Start-Up
(single-phase and three-phase). 6. Operation and commissionning manuals Description QR code Link Commissionning Click here manual Operation and maintenance Click here manual www.swegon.com We reserve the right to alter specifications. - Page 11 4 positions HMI TACtouch Modbus Duct Click here Click here touchscreen TAC6 pressure sensor Room temperature Click here Kit 5 Output relays Click here sensor 0-10V Duct Click here pressure sensor www.swegon.com We reserve the right to alter specifications.
-
Page 12: Main Board
GB.ESENSA.MI.230612 8. Main board www.swegon.com We reserve the right to alter specifications. - Page 13 GREEN LED ON = POWERED ON ply flow (option - prewired) RED LED ON = ALARM RJ4 = RJ12 connector for Modbus Pressure CA mode on ex- haust flow and defrost detecting (option - prewired) www.swegon.com We reserve the right to alter specifications.
- Page 14 GB.ESENSA.MI.230612 The document was originally written in English. www.swegon.com We reserve the right to alter specifications.
Need help?
Do you have a question about the ESENSA PX TOP 05 and is the answer not in the manual?
Questions and answers